IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v36y2011i10p5832-5837.html
   My bibliography  Save this article

Comparison of the performance of a spark-ignited gasoline engine blended with hydrogen and hydrogen–oxygen mixtures

Author

Listed:
  • Wang, Shuofeng
  • Ji, Changwei
  • Zhang, Jian
  • Zhang, Bo

Abstract

This paper compared the effects of hydrogen and hydrogen–oxygen blends (hydroxygen) additions on the performance of a gasoline engine at 1400 rpm and a manifolds absolute pressure of 61.5 kPa. The tests were carried out on a 1.6 L gasoline engine equipped with a hydrogen and oxygen injection system. A hybrid electronic control unit was applied to adjust the hydrogen and hydroxygen volume fractions in the intake increasing from 0% to about 3% and keep the hydrogen-to-oxygen mole ratio at 2:1 in hydroxygen tests. For each testing condition, the gasoline flow rate was adjusted to maintain the mixture global excess air ratio at 1.00. The test results confirmed that engine fuel energy flow rate was decreased after hydrogen addition but increased with hydroxygen blending. When hydrogen or hydroxygen volume fraction in the intake was lower than 2%, the hydroxygen-blended gasoline engine produced a higher thermal efficiency than the hydrogen-blended gasoline engine. Both the additions of hydrogen and hydroxygen help reduce flame development and propagation periods of the gasoline engine. HC emissions were reduced whereas NOx emissions were raised with the increase of hydrogen and hydroxygen addition levels. CO was slightly increased after hydrogen blending, but reduced with hydroxygen addition.

Suggested Citation

  • Wang, Shuofeng & Ji, Changwei & Zhang, Jian & Zhang, Bo, 2011. "Comparison of the performance of a spark-ignited gasoline engine blended with hydrogen and hydrogen–oxygen mixtures," Energy, Elsevier, vol. 36(10), pages 5832-5837.
    • Handle: RePEc:eee:energy:v:36:y:2011:i:10:p:5832-5837
    DOI: 10.1016/j.energy.2011.08.042
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544211005822
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2011.08.042?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Vudumu, Shravan K. & Koylu, Umit O., 2011. "Computational modeling, validation, and utilization for predicting the performance, combustion and emission characteristics of hydrogen IC engines," Energy, Elsevier, vol. 36(1), pages 647-655.
    2. Marshall, A. & Børresen, B. & Hagen, G. & Tsypkin, M. & Tunold, R., 2007. "Hydrogen production by advanced proton exchange membrane (PEM) water electrolysers—Reduced energy consumption by improved electrocatalysis," Energy, Elsevier, vol. 32(4), pages 431-436.
    3. Neef, H.-J., 2009. "International overview of hydrogen and fuel cell research," Energy, Elsevier, vol. 34(3), pages 327-333.
    4. Berry, Gene D. & Pasternak, Alan D. & Rambach, Glenn D. & Ray Smith, J. & Schock, Robert N., 1996. "Hydrogen as a future transportation fuel," Energy, Elsevier, vol. 21(4), pages 289-303.
    5. Guo, Liang & Li, Xiao-Ming & Zeng, Guang-Ming & Zhou, Yi, 2010. "Effective hydrogen production using waste sludge and its filtrate," Energy, Elsevier, vol. 35(9), pages 3557-3562.
    6. Abanades, Stéphane & Charvin, Patrice & Flamant, Gilles & Neveu, Pierre, 2006. "Screening of water-splitting thermochemical cycles potentially attractive for hydrogen production by concentrated solar energy," Energy, Elsevier, vol. 31(14), pages 2805-2822.
    7. Rakopoulos, C.D. & Scott, M.A. & Kyritsis, D.C. & Giakoumis, E.G., 2008. "Availability analysis of hydrogen/natural gas blends combustion in internal combustion engines," Energy, Elsevier, vol. 33(2), pages 248-255.
    8. Rosen, Marc A., 2010. "Advances in hydrogen production by thermochemical water decomposition: A review," Energy, Elsevier, vol. 35(2), pages 1068-1076.
    9. Ting, David S.-K. & Reader, Graham T., 2005. "Hydrogen peroxide for improving premixed methane–air combustion," Energy, Elsevier, vol. 30(2), pages 313-322.
    10. Medrano, J.A. & Oliva, M. & Ruiz, J. & García, L. & Arauzo, J., 2011. "Hydrogen from aqueous fraction of biomass pyrolysis liquids by catalytic steam reforming in fluidized bed," Energy, Elsevier, vol. 36(4), pages 2215-2224.
    11. Yüksel, F. & Ceviz, M.A., 2003. "Thermal balance of a four stroke SI engine operating on hydrogen as a supplementary fuel," Energy, Elsevier, vol. 28(11), pages 1069-1080.
    12. Wang, Shuofeng & Ji, Changwei & Zhang, Bo, 2010. "Effects of hydrogen addition and cylinder cutoff on combustion and emissions performance of a spark-ignited gasoline engine under a low operating condition," Energy, Elsevier, vol. 35(12), pages 4754-4760.
    13. Fan, Mei–qiang & Sun, Li–xian & Xu, Fen, 2010. "Experiment assessment of hydrogen production from activated aluminum alloys in portable generator for fuel cell applications," Energy, Elsevier, vol. 35(7), pages 2922-2926.
    14. Bysveen, Marie, 2007. "Engine characteristics of emissions and performance using mixtures of natural gas and hydrogen," Energy, Elsevier, vol. 32(4), pages 482-489.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Catapano, F. & Di Iorio, S. & Sementa, P. & Vaglieco, B.M., 2016. "Analysis of energy efficiency of methane and hydrogen-methane blends in a PFI/DI SI research engine," Energy, Elsevier, vol. 117(P2), pages 378-387.
    2. Catapano, F. & Di Iorio, S. & Magno, A. & Sementa, P. & Vaglieco, B.M., 2015. "A comprehensive analysis of the effect of ethanol, methane and methane-hydrogen blend on the combustion process in a PFI (port fuel injection) engine," Energy, Elsevier, vol. 88(C), pages 101-110.
    3. Wang, Shuofeng & Ji, Changwei & Zhang, Bo & Cong, Xiaoyu & Liu, Xiaolong, 2016. "Effect of CO2 dilution on combustion and emissions characteristics of the hydrogen-enriched gasoline engine," Energy, Elsevier, vol. 96(C), pages 118-126.
    4. Wu, Horng-Wen & Wu, Zhan-Yi, 2012. "Combustion characteristics and optimal factors determination with Taguchi method for diesel engines port-injecting hydrogen," Energy, Elsevier, vol. 47(1), pages 411-420.
    5. Hassan, Haroun & Aissa, Walid A. & Eissa, Mohamed S. & Abdel-Mohsen, Hesham S., 2022. "Enhancement of the performance and emissions reduction of a hydroxygen-blended gasoline engine using different catalysts," Applied Energy, Elsevier, vol. 326(C).
    6. Chen, Guan-Bang & Li, Yueh-Heng & Cheng, Tsarng-Sheng & Chao, Yei-Chin, 2013. "Chemical effect of hydrogen peroxide addition on characteristics of methane–air combustion," Energy, Elsevier, vol. 55(C), pages 564-570.
    7. Su, Teng & Ji, Changwei & Wang, Shuofeng & Shi, Lei & Yang, Jinxin & Cong, Xiaoyu, 2017. "Investigation on performance of a hydrogen-gasoline rotary engine at part load and lean conditions," Applied Energy, Elsevier, vol. 205(C), pages 683-691.
    8. Gao, Jianbing & Tian, Guohong & Ma, Chaochen & Xing, Shikai & Jenner, Phil, 2021. "Performance explorations of a naturally aspirated opposed rotary piston engine fuelled with hydrogen under part load and stoichiometric conditions using a numerical simulation approach," Energy, Elsevier, vol. 222(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Vudumu, Shravan K. & Koylu, Umit O., 2011. "Computational modeling, validation, and utilization for predicting the performance, combustion and emission characteristics of hydrogen IC engines," Energy, Elsevier, vol. 36(1), pages 647-655.
    2. Park, Cheolwoong & Kim, Changgi & Choi, Young & Lee, Janghee, 2013. "Operating strategy for exhaust gas reduction and performance improvement in a heavy-duty hydrogen-natural gas blend engine," Energy, Elsevier, vol. 50(C), pages 262-269.
    3. Wu, Horng-Wen & Wu, Zhan-Yi, 2012. "Combustion characteristics and optimal factors determination with Taguchi method for diesel engines port-injecting hydrogen," Energy, Elsevier, vol. 47(1), pages 411-420.
    4. Wang, Shuofeng & Ji, Changwei & Zhang, Bo, 2010. "Effects of hydrogen addition and cylinder cutoff on combustion and emissions performance of a spark-ignited gasoline engine under a low operating condition," Energy, Elsevier, vol. 35(12), pages 4754-4760.
    5. Fan, Mei-Qiang & Liu, Shu-sheng & Zhang, Yao & Zhang, Jian & Sun, Li-Xian & Xu, Fen, 2010. "Superior hydrogen storage properties of MgH2–10 wt.% TiC composite," Energy, Elsevier, vol. 35(8), pages 3417-3421.
    6. Deb, Madhujit & Debbarma, Bishop & Majumder, Arindam & Banerjee, Rahul, 2016. "Performance –emission optimization of a diesel-hydrogen dual fuel operation: A NSGA II coupled TOPSIS MADM approach," Energy, Elsevier, vol. 117(P1), pages 281-290.
    7. Chen, Guan-Bang & Li, Yueh-Heng & Cheng, Tsarng-Sheng & Chao, Yei-Chin, 2013. "Chemical effect of hydrogen peroxide addition on characteristics of methane–air combustion," Energy, Elsevier, vol. 55(C), pages 564-570.
    8. Djouadi, Amel & Bentahar, Fatiha, 2016. "Combustion study of a spark-ignition engine from pressure cycles," Energy, Elsevier, vol. 101(C), pages 211-217.
    9. Lin, Kuang C. & Lin, Yuan-Chung & Hsiao, Yi-Hsing, 2014. "Microwave plasma studies of Spirulina algae pyrolysis with relevance to hydrogen production," Energy, Elsevier, vol. 64(C), pages 567-574.
    10. González Rodríguez, Daniel & Brayner de Oliveira Lira, Carlos Alberto & García Parra, Lázaro Roger & García Hernández, Carlos Rafael & de la Torre Valdés, Raciel, 2018. "Computational model of a sulfur-iodine thermochemical water splitting system coupled to a VHTR for nuclear hydrogen production," Energy, Elsevier, vol. 147(C), pages 1165-1176.
    11. Jamey Davies & Stephanus P. Du Preez & Dmitri G. Bessarabov, 2022. "The Hydrolysis of Ball-Milled Aluminum–Bismuth–Nickel Composites for On-Demand Hydrogen Generation," Energies, MDPI, vol. 15(7), pages 1-22, March.
    12. Ma, Li-Juan & Wang, Jianfeng & Han, Min & Jia, Jianfeng & Wu, Hai-Shun & Zhang, Xiang, 2019. "Adsorption of multiple H2 molecules on the complex TiC6H6: An unusual combination of chemisorption and physisorption," Energy, Elsevier, vol. 171(C), pages 315-325.
    13. Santos, D.M.F. & Šljukić, B. & Sequeira, C.A.C. & Macciò, D. & Saccone, A. & Figueiredo, J.L., 2013. "Electrocatalytic approach for the efficiency increase of electrolytic hydrogen production: Proof-of-concept using platinum--dysprosium alloys," Energy, Elsevier, vol. 50(C), pages 486-492.
    14. Wang, Shuofeng & Ji, Changwei & Zhang, Bo & Cong, Xiaoyu & Liu, Xiaolong, 2016. "Effect of CO2 dilution on combustion and emissions characteristics of the hydrogen-enriched gasoline engine," Energy, Elsevier, vol. 96(C), pages 118-126.
    15. Tamilarasan, P. & Ramaprabhu, S., 2013. "Graphene based all-solid-state supercapacitors with ionic liquid incorporated polyacrylonitrile electrolyte," Energy, Elsevier, vol. 51(C), pages 374-381.
    16. Yadav, Deepak & Banerjee, Rangan, 2016. "A review of solar thermochemical processes," Renewable and Sustainable Energy Reviews, Elsevier, vol. 54(C), pages 497-532.
    17. Liu, Yongan & Wang, Xinhua & Dong, Zhaohui & Liu, Haizhen & Li, Shouquan & Ge, Hongwei & Yan, Mi, 2013. "Hydrogen generation from the hydrolysis of Mg powder ball-milled with AlCl3," Energy, Elsevier, vol. 53(C), pages 147-152.
    18. Wang, Xin & Zhang, Hongguang & Yao, Baofeng & Lei, Yan & Sun, Xiaona & Wang, Daojing & Ge, Yunshan, 2012. "Experimental study on factors affecting lean combustion limit of S.I engine fueled with compressed natural gas and hydrogen blends," Energy, Elsevier, vol. 38(1), pages 58-65.
    19. El-Askary, W.A. & Sakr, I.M. & Ibrahim, K.A. & Balabel, A., 2015. "Hydrodynamics characteristics of hydrogen evolution process through electrolysis: Numerical and experimental studies," Energy, Elsevier, vol. 90(P1), pages 722-737.
    20. Abánades, A. & Rubbia, C. & Salmieri, D., 2012. "Technological challenges for industrial development of hydrogen production based on methane cracking," Energy, Elsevier, vol. 46(1), pages 359-363.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:36:y:2011:i:10:p:5832-5837. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.