IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v88y2011i1p111-126.html
   My bibliography  Save this article

Investigating the effect of crevice flow on internal combustion engines using a new simple crevice model implemented in a CFD code

Author

Listed:
  • Rakopoulos, C.D.
  • Kosmadakis, G.M.
  • Dimaratos, A.M.
  • Pariotis, E.G.

Abstract

A theoretical investigation is conducted to examine the way the crevice regions affect the mean cylinder pressure, the in-cylinder temperature, and the velocity field of internal combustion engines running at motoring conditions. For the calculation of the wall heat flux, a wall heat transfer formulation developed by the authors is used, while for the simulation of the crevices and the blow-by a newly developed simplified simulation model is presented herein. These sub-models are incorporated into an in-house Computational Fluid Dynamics (CFD) code. The main advantage of the new crevice model is that it can be applied in cases where no detailed information of the ring-pack configuration is available, which is important as this information is rarely known or may have been altered during the engine's life. Thus, an adequate estimation of the blow-by effect on the cylinder pressure can be drawn. To validate the new model, the measured in-cylinder pressure traces of a diesel engine, located at the authors' laboratory, running under motoring conditions at four engine speeds were used as reference, together with measured velocity profiles and turbulence data of a motored spark-ignition engine. Comparing the predicted and measured cylinder pressure traces of the diesel engine for all cases examined, it is observed that by incorporating the new crevice sub-model into the in-house CFD code, significant improvements on the predictive accuracy of the model is obtained. The calculated cylinder pressure traces almost coincide with the measured ones, thus avoiding the use of any calibration constants as would have been the case with the crevice effect omitted. Concerning the radial and swirl velocity profiles and the turbulent kinetic energy measured in the spark-ignition engine, the validation process revealed that the developed crevice model has a minor influence on the aforementioned parameters. The theoretical study has been extended by investigating in the same spark-ignition engine, during the induction and compression strokes, the way crevice flow affects the thermodynamic properties of the air trapped in the cylinder.

Suggested Citation

  • Rakopoulos, C.D. & Kosmadakis, G.M. & Dimaratos, A.M. & Pariotis, E.G., 2011. "Investigating the effect of crevice flow on internal combustion engines using a new simple crevice model implemented in a CFD code," Applied Energy, Elsevier, vol. 88(1), pages 111-126, January.
    • Handle: RePEc:eee:appene:v:88:y:2011:i:1:p:111-126
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306-2619(10)00281-3
    Download Restriction: Full text for ScienceDirect subscribers only
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Rakopoulos, C.D. & Kosmadakis, G.M. & Pariotis, E.G., 2010. "Critical evaluation of current heat transfer models used in CFD in-cylinder engine simulations and establishment of a comprehensive wall-function formulation," Applied Energy, Elsevier, vol. 87(5), pages 1612-1630, May.
    2. Mikalsen, R. & Roskilly, A.P., 2009. "Coupled dynamic-multidimensional modelling of free-piston engine combustion," Applied Energy, Elsevier, vol. 86(1), pages 89-95, January.
    3. Mikalsen, R. & Roskilly, A.P., 2009. "A computational study of free-piston diesel engine combustion," Applied Energy, Elsevier, vol. 86(7-8), pages 1136-1143, July.
    4. Komninos, N.P., 2009. "Modeling HCCI combustion: Modification of a multi-zone model and comparison to experimental results at varying boost pressure," Applied Energy, Elsevier, vol. 86(10), pages 2141-2151, October.
    5. Sala, J.M. & López-González, L.M. & Ruiz de Adana, M. & Eguía, J. & Flores, I. & Míguez, J.L., 2006. "Optimising ventilation-system design for a container-housed engine," Applied Energy, Elsevier, vol. 83(10), pages 1125-1138, October.
    6. Xiao, Jin & Li, Qingfeng & Huang, Zhen, 2010. "Motion characteristic of a free piston linear engine," Applied Energy, Elsevier, vol. 87(4), pages 1288-1294, April.
    7. Rakopoulos, C.D. & Kosmadakis, G.M. & Pariotis, E.G., 2009. "Evaluation of a new computational fluid dynamics model for internal combustion engines using hydrogen under motoring conditions," Energy, Elsevier, vol. 34(12), pages 2158-2166.
    8. Komninos, N.P., 2009. "Investigating the importance of mass transfer on the formation of HCCI engine emissions using a multi-zone model," Applied Energy, Elsevier, vol. 86(7-8), pages 1335-1343, July.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Curto-Risso, P.L. & Medina, A. & Calvo Hernández, A. & Guzmán-Vargas, L. & Angulo-Brown, F., 2011. "On cycle-to-cycle heat release variations in a simulated spark ignition heat engine," Applied Energy, Elsevier, vol. 88(5), pages 1557-1567, May.
    2. Fukang Ma & Changlu Zhao & Fujun Zhang & Zhenfeng Zhao & Shuanlu Zhang, 2015. "Effects of Scavenging System Configuration on In-Cylinder Air Flow Organization of an Opposed-Piston Two-Stroke Engine," Energies, MDPI, vol. 8(6), pages 1-19, June.
    3. Salvi, B.L. & Subramanian, K.A., 2015. "Experimental investigation and phenomenological model development of flame kernel growth rate in a gasoline fuelled spark ignition engine," Applied Energy, Elsevier, vol. 139(C), pages 93-103.
    4. Kim, Joonsuk & Chun, Kwang Min & Song, Soonho & Baek, Hong-Kil & Lee, Seung Woo, 2018. "Hydrogen effects on the combustion stability, performance and emissions of a turbo gasoline direct injection engine in various air/fuel ratios," Applied Energy, Elsevier, vol. 228(C), pages 1353-1361.
    5. Chatzopoulou, Maria Anna & Markides, Christos N., 2018. "Thermodynamic optimisation of a high-electrical efficiency integrated internal combustion engine – Organic Rankine cycle combined heat and power system," Applied Energy, Elsevier, vol. 226(C), pages 1229-1251.
    6. Irimescu, Adrian, 2012. "Performance and fuel conversion efficiency of a spark ignition engine fueled with iso-butanol," Applied Energy, Elsevier, vol. 96(C), pages 477-483.
    7. Gnana Sagaya Raj, Antony Raj & Mallikarjuna, Jawali Maharudrappa & Ganesan, Venkitachalam, 2013. "Energy efficient piston configuration for effective air motion – A CFD study," Applied Energy, Elsevier, vol. 102(C), pages 347-354.
    8. Bari, S. & Saad, Idris, 2014. "Effect of guide vane height on the performance and emissions of a compression ignition (CI) engine run with biodiesel through simulation and experiment," Applied Energy, Elsevier, vol. 136(C), pages 431-444.
    9. Liu, Kaimin & Li, Yangtao & Yang, Jing & Deng, Banglin & Feng, Renhua & Huang, Yanjun, 2018. "Comprehensive study of key operating parameters on combustion characteristics of butanol-gasoline blends in a high speed SI engine," Applied Energy, Elsevier, vol. 212(C), pages 13-32.
    10. Kan, Xiang & Zhou, Dezhi & Yang, Wenming & Zhai, Xiaoqiang & Wang, Chi-Hwa, 2018. "An investigation on utilization of biogas and syngas produced from biomass waste in premixed spark ignition engine," Applied Energy, Elsevier, vol. 212(C), pages 210-222.
    11. Nikolaos Diangelakis & Christos Panos & Efstratios Pistikopoulos, 2014. "Design optimization of an internal combustion engine powered CHP system for residential scale application," Computational Management Science, Springer, vol. 11(3), pages 237-266, July.
    12. Payri, F. & Olmeda, P. & Martín, J. & García, A., 2011. "A complete 0D thermodynamic predictive model for direct injection diesel engines," Applied Energy, Elsevier, vol. 88(12), pages 4632-4641.
    13. Chalet, David & Mahe, Alexandre & Migaud, Jérôme & Hetet, Jean-François, 2011. "A frequency modelling of the pressure waves in the inlet manifold of internal combustion engine," Applied Energy, Elsevier, vol. 88(9), pages 2988-2994.
    14. Krishna, Addepalli S. & Mallikarjuna, J.M. & Kumar, Davinder, 2016. "Effect of engine parameters on in-cylinder flows in a two-stroke gasoline direct injection engine," Applied Energy, Elsevier, vol. 176(C), pages 282-294.
    15. Tan, Shin Mei & Ng, Hoon Kiat & Gan, Suyin, 2013. "Computational study of crevice soot entrainment in a diesel engine," Applied Energy, Elsevier, vol. 102(C), pages 898-907.
    16. Titilope Ibukun Banji & Gregg Arney & Mark Patterson & Daniel B. Olsen, 2024. "Reduction of Methane Emissions from Natural Gas Integral Compressor Engines through Fuel Injection Control," Sustainability, MDPI, vol. 16(14), pages 1-20, July.
    17. Simpson, Michael C. & Chatzopoulou, Maria Anna & Oyewunmi, Oyeniyi A. & Le Brun, Niccolo & Sapin, Paul & Markides, Christos N., 2019. "Technoeconomic analysis of internal combustion engine – organic Rankine cycle systems for combined heat and power in energy-intensive buildings," Applied Energy, Elsevier, vol. 253(C), pages 1-1.
    18. Shen, Zhaojie & Wang, Xinyan & Zhao, Hua & Lin, Bo & Shen, Yitao & Yang, Jianguo, 2021. "Numerical investigation of natural gas-diesel dual-fuel engine with different piston geometries and radial clearances," Energy, Elsevier, vol. 220(C).
    19. George M. Kosmadakis & Constantine D. Rakopoulos, 2019. "A Fast CFD-Based Methodology for Determining the Cyclic Variability and Its Effects on Performance and Emissions of Spark-Ignition Engines," Energies, MDPI, vol. 12(21), pages 1-15, October.
    20. Wonjun Yoon & Jeong-Won Lee & Jungsoo Park, 2024. "Numerical Study on Prediction of Icing Phenomena in Fresh Air and Blow-by Gas Mixing Region of Diesel Engine under High Velocity of Intake Air Condition," Energies, MDPI, vol. 17(7), pages 1-15, April.
    21. Mohamed Ismail, Harun & Ng, Hoon Kiat & Gan, Suyin, 2012. "Evaluation of non-premixed combustion and fuel spray models for in-cylinder diesel engine simulation," Applied Energy, Elsevier, vol. 90(1), pages 271-279.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Krishna, Addepalli S. & Mallikarjuna, J.M. & Kumar, Davinder, 2016. "Effect of engine parameters on in-cylinder flows in a two-stroke gasoline direct injection engine," Applied Energy, Elsevier, vol. 176(C), pages 282-294.
    2. Komninos, N.P. & Kosmadakis, G.M., 2011. "Heat transfer in HCCI multi-zone modeling: Validation of a new wall heat flux correlation under motoring conditions," Applied Energy, Elsevier, vol. 88(5), pages 1635-1648, May.
    3. Peng Sun & Chi Zhang & Jinhua Chen & Fei Zhao & Youyong Liao & Guilin Yang & Chinyin Chen, 2016. "Decoupling Design and Verification of a Free-Piston Linear Generator," Energies, MDPI, vol. 9(12), pages 1-23, December.
    4. Lim, Ocktaeck & Hung, Nguyen Ba & Oh, Seokyoung & Kim, Gangchul & Song, Hanho & Iida, Norimasa, 2015. "A study of operating parameters on the linear spark ignition engine," Applied Energy, Elsevier, vol. 160(C), pages 746-760.
    5. Yuan, Chenheng & Feng, Huihua & He, Yituan & Xu, Jing, 2016. "Combustion characteristics analysis of a free-piston engine generator coupling with dynamic and scavenging," Energy, Elsevier, vol. 102(C), pages 637-649.
    6. Komninos, N.P. & Rakopoulos, C.D., 2016. "Heat transfer in hcci phenomenological simulation models: A review," Applied Energy, Elsevier, vol. 181(C), pages 179-209.
    7. Mohamed Ismail, Harun & Ng, Hoon Kiat & Gan, Suyin, 2012. "Evaluation of non-premixed combustion and fuel spray models for in-cylinder diesel engine simulation," Applied Energy, Elsevier, vol. 90(1), pages 271-279.
    8. Rakopoulos, C.D. & Kosmadakis, G.M. & Pariotis, E.G., 2010. "Critical evaluation of current heat transfer models used in CFD in-cylinder engine simulations and establishment of a comprehensive wall-function formulation," Applied Energy, Elsevier, vol. 87(5), pages 1612-1630, May.
    9. Yuxi Miao & Zhengxing Zuo & Huihua Feng & Chendong Guo & Yu Song & Boru Jia & Yuyao Guo, 2016. "Research on the Combustion Characteristics of a Free-Piston Gasoline Engine Linear Generator during the Stable Generating Process," Energies, MDPI, vol. 9(8), pages 1-19, August.
    10. Guo, Chendong & Zuo, Zhengxing & Feng, Huihua & Jia, Boru & Roskilly, Tony, 2020. "Review of recent advances of free-piston internal combustion engine linear generator," Applied Energy, Elsevier, vol. 269(C).
    11. Mao, Jinlong & Zuo, Zhengxing & Feng, Huihua, 2011. "Parameters coupling designation of diesel free-piston linear alternator," Applied Energy, Elsevier, vol. 88(12), pages 4577-4589.
    12. Gan, Suyin & Ng, Hoon Kiat & Pang, Kar Mun, 2011. "Homogeneous Charge Compression Ignition (HCCI) combustion: Implementation and effects on pollutants in direct injection diesel engines," Applied Energy, Elsevier, vol. 88(3), pages 559-567, March.
    13. Xu, Zhaoping & Chang, Siqin, 2010. "Prototype testing and analysis of a novel internal combustion linear generator integrated power system," Applied Energy, Elsevier, vol. 87(4), pages 1342-1348, April.
    14. Hou, Junxing & Qiao, Xinqi & Wang, Zhen & Liu, Wei & Huang, Zhen, 2010. "Characterization of knocking combustion in HCCI DME engine using wavelet packet transform," Applied Energy, Elsevier, vol. 87(4), pages 1239-1246, April.
    15. Hung, Nguyen Ba & Lim, Ocktaeck, 2016. "A review of free-piston linear engines," Applied Energy, Elsevier, vol. 178(C), pages 78-97.
    16. Maurya, Rakesh Kumar & Agarwal, Avinash Kumar, 2011. "Experimental investigation on the effect of intake air temperature and air-fuel ratio on cycle-to-cycle variations of HCCI combustion and performance parameters," Applied Energy, Elsevier, vol. 88(4), pages 1153-1163, April.
    17. Wu, Limin & Feng, Huihua & Jia, Boru & Tang, Zhifeng & Yan, Xiaodong & Wang, Wei, 2022. "A novel method to investigate the power generation characteristics of linear generator in full frequency operation range applied to opposed-piston free-piston engine generator _ Simulation and test re," Energy, Elsevier, vol. 254(PB).
    18. Zhao, Xiaohuan & Liu, Fang & Wang, Chunhua, 2022. "Effects of different piston combustion chamber heights on heat transfer and energy conversion performance enhancement of a heavy-duty truck diesel engine," Energy, Elsevier, vol. 249(C).
    19. Hung, Nguyen Ba & Lim, Ocktaeck & Iida, Norimasa, 2015. "The effects of key parameters on the transition from SI combustion to HCCI combustion in a two-stroke free piston linear engine," Applied Energy, Elsevier, vol. 137(C), pages 385-401.
    20. Wu, Horng-Wen & Wang, Ren-Hung & Ou, Dung-Je & Chen, Ying-Chuan & Chen, Teng-yu, 2011. "Reduction of smoke and nitrogen oxides of a partial HCCI engine using premixed gasoline and ethanol with air," Applied Energy, Elsevier, vol. 88(11), pages 3882-3890.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:88:y:2011:i:1:p:111-126. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.