IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v99y2012icp393-401.html
   My bibliography  Save this article

Study on heat transfer and pressure drop performances of ribbed channel in the high temperature heat exchanger

Author

Listed:
  • Ma, Ting
  • Wang, Qiu-wang
  • Zeng, Min
  • Chen, Yi-tung
  • Liu, Yang
  • Nagarajan, Vijaisri

Abstract

In this paper, the effects of inlet temperature and rib height on the fluid flow and heat transfer performances of the ribbed channel inside the high temperature heat exchanger are presented. The inlet temperature varies from 850K to 1250K and the ratio of rib height to channel height varies from 0.083 to 0.333. The results indicate that increasing the rib height can enhance the flow disturbance and hence improve the heat transfer performance. The inlet temperature has little effect on the basic structure of fluid flow and the heat transfer is enhanced due to the increased velocity. Compared to increasing the rib height, more heat can be transferred by increasing the inlet temperature with less pressure drop. The high pressure drop is more serious as the inlet temperature increases. It is proposed to use the compact heat transfer structure at the low temperature region and replace it by loose heat transfer structure at the high temperature region. It also demonstrates that the Nusselt number and friction factor are unsuitable to compare the heat transfer and pressure drop performances among different temperature conditions because the physical properties of fluid change with temperature variation.

Suggested Citation

  • Ma, Ting & Wang, Qiu-wang & Zeng, Min & Chen, Yi-tung & Liu, Yang & Nagarajan, Vijaisri, 2012. "Study on heat transfer and pressure drop performances of ribbed channel in the high temperature heat exchanger," Applied Energy, Elsevier, vol. 99(C), pages 393-401.
    • Handle: RePEc:eee:appene:v:99:y:2012:i:c:p:393-401
    DOI: 10.1016/j.apenergy.2012.05.030
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261912004035
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2012.05.030?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Akansu, Selahaddin Orhan, 2006. "Heat transfers and pressure drops for porous-ring turbulators in a circular pipe," Applied Energy, Elsevier, vol. 83(3), pages 280-298, March.
    2. Leung, C. W. & Wong, T. T. & Probert, S. D., 2001. "Enhanced forced-convection from ribbed or machine-roughened inner surfaces within triangular ducts," Applied Energy, Elsevier, vol. 69(2), pages 87-99, June.
    3. Datta, Amitava & Ganguly, Ranjan & Sarkar, Luna, 2010. "Energy and exergy analyses of an externally fired gas turbine (EFGT) cycle integrated with biomass gasifier for distributed power generation," Energy, Elsevier, vol. 35(1), pages 341-350.
    4. Shaeri, M.R. & Yaghoubi, M. & Jafarpur, K., 2009. "Heat transfer analysis of lateral perforated fin heat sinks," Applied Energy, Elsevier, vol. 86(10), pages 2019-2029, October.
    5. Singh, Sukhmeet & Chander, Subhash & Saini, J.S., 2012. "Investigations on thermo-hydraulic performance due to flow-attack-angle in V-down rib with gap in a rectangular duct of solar air heater," Applied Energy, Elsevier, vol. 97(C), pages 907-912.
    6. Ozceyhan, Veysel & Gunes, Sibel & Buyukalaca, Orhan & Altuntop, Necdet, 2008. "Heat transfer enhancement in a tube using circular cross sectional rings separated from wall," Applied Energy, Elsevier, vol. 85(10), pages 988-1001, October.
    7. Chaube, Alok & Sahoo, P.K. & Solanki, S.C., 2006. "Analysis of heat transfer augmentation and flow characteristics due to rib roughness over absorber plate of a solar air heater," Renewable Energy, Elsevier, vol. 31(3), pages 317-331.
    8. Leung, C. W. & Chan, T. L. & Probert, S. D. & Kang, H. J., 1999. "Forced convection from a horizontal ribbed rectangular base-plate penetrated by arrays of holes," Applied Energy, Elsevier, vol. 62(2), pages 81-95, February.
    9. Leung, C. W. & Chen, S. & Wong, T. T. & Probert, S. D., 2000. "Forced convection and pressure drop in a horizontal triangular-sectional duct with V-grooved (i.e. orthogonal to the mean flow) inner surfaces," Applied Energy, Elsevier, vol. 66(3), pages 199-211, July.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Iora, P. & Silva, P., 2013. "Innovative combined heat and power system based on a double shaft intercooled externally fired gas cycle," Applied Energy, Elsevier, vol. 105(C), pages 108-115.
    2. Sheikholeslami, M. & Ganji, D.D., 2016. "Heat transfer enhancement in an air to water heat exchanger with discontinuous helical turbulators; experimental and numerical studies," Energy, Elsevier, vol. 116(P1), pages 341-352.
    3. Kuruneru, Sahan Trushad Wickramasooriya & Sauret, Emilie & Saha, Suvash Chandra & Gu, YuanTong, 2016. "Numerical investigation of the temporal evolution of particulate fouling in metal foams for air-cooled heat exchangers," Applied Energy, Elsevier, vol. 184(C), pages 531-547.
    4. Namkyu Lee & Beom Seok Kim & Hokyu Moon & Joon-Soo Lim & Hyung Hee Cho, 2019. "Heat-Absorbing Capacity of High-Heat-Flux Components in Nuclear Fusion Reactors," Energies, MDPI, vol. 12(19), pages 1-15, October.
    5. Nagarajan, Vijaisri & Chen, Yitung & Wang, Qiuwang & Ma, Ting, 2014. "Hydraulic and thermal performances of a novel configuration of high temperature ceramic plate-fin heat exchanger," Applied Energy, Elsevier, vol. 113(C), pages 589-602.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Nidhul, Kottayat & Kumar, Sachin & Yadav, Ajay Kumar & Anish, S., 2020. "Enhanced thermo-hydraulic performance in a V-ribbed triangular duct solar air heater: CFD and exergy analysis," Energy, Elsevier, vol. 200(C).
    2. Kumar, Rajneesh & Varun, & Kumar, Anoop, 2016. "Thermal and fluid dynamic characteristics of flow through triangular cross-sectional duct: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 61(C), pages 123-140.
    3. Kumar, Rajneesh & Kumar, Anoop & Goel, Varun, 2019. "Performance improvement and development of correlation for friction factor and heat transfer using computational fluid dynamics for ribbed triangular duct solar air heater," Renewable Energy, Elsevier, vol. 131(C), pages 788-799.
    4. Singh Yadav, Anil & Kumar Thapak, Manish, 2014. "Artificially roughened solar air heater: Experimental investigations," Renewable and Sustainable Energy Reviews, Elsevier, vol. 36(C), pages 370-411.
    5. Varun Kumar B. & G. Manikandan & P. Rajesh Kanna & Dawid Taler & Jan Taler & Marzena Nowak-Ocłoń & Karol Mzyk & Hoong Thiam Toh, 2018. "A Performance Evaluation of a Solar Air Heater Using Different Shaped Ribs Mounted on the Absorber Plate—A Review," Energies, MDPI, vol. 11(11), pages 1-20, November.
    6. Alam, Tabish & Saini, R.P. & Saini, J.S., 2014. "Use of turbulators for heat transfer augmentation in an air duct – A review," Renewable Energy, Elsevier, vol. 62(C), pages 689-715.
    7. Thakur, Deep Singh & Khan, Mohd. Kaleem & Pathak, Manabendra, 2017. "Solar air heater with hyperbolic ribs: 3D simulation with experimental validation," Renewable Energy, Elsevier, vol. 113(C), pages 357-368.
    8. Kumar, Sharad & Saini, R.P., 2009. "CFD based performance analysis of a solar air heater duct provided with artificial roughness," Renewable Energy, Elsevier, vol. 34(5), pages 1285-1291.
    9. Rajaseenivasan, T. & Srinivasan, S. & Srithar, K., 2015. "Comprehensive study on solar air heater with circular and V-type turbulators attached on absorber plate," Energy, Elsevier, vol. 88(C), pages 863-873.
    10. Jin, Dongxu & Zhang, Manman & Wang, Ping & Xu, Shasha, 2015. "Numerical investigation of heat transfer and fluid flow in a solar air heater duct with multi V-shaped ribs on the absorber plate," Energy, Elsevier, vol. 89(C), pages 178-190.
    11. Loha, Chanchal & Chattopadhyay, Himadri & Chatterjee, Pradip K., 2011. "Thermodynamic analysis of hydrogen rich synthetic gas generation from fluidized bed gasification of rice husk," Energy, Elsevier, vol. 36(7), pages 4063-4071.
    12. Zang, Guiyan & Zhang, Jianan & Jia, Junxi & Lora, Electo Silva & Ratner, Albert, 2020. "Life cycle assessment of power-generation systems based on biomass integrated gasification combined cycles," Renewable Energy, Elsevier, vol. 149(C), pages 336-346.
    13. Athari, Hassan & Soltani, Saeed & Seyed Mahmoudi, Seyed Mohammad & Rosen, Marc A. & Morosuk, Tatiana, 2014. "Exergoeconomic analysis of a biomass post-firing combined-cycle power plant," Energy, Elsevier, vol. 77(C), pages 553-561.
    14. Sheikholeslami, M. & Ganji, D.D., 2016. "Heat transfer enhancement in an air to water heat exchanger with discontinuous helical turbulators; experimental and numerical studies," Energy, Elsevier, vol. 116(P1), pages 341-352.
    15. Qader, Bootan S. & Supeni, E.E. & Ariffin, M.K.A. & Talib, A.R. Abu, 2019. "Numerical investigation of flow through inclined fins under the absorber plate of solar air heater," Renewable Energy, Elsevier, vol. 141(C), pages 468-481.
    16. Leonardo Pierobon & Tuong-Van Nguyen & Andrea Mazzucco & Ulrik Larsen & Fredrik Haglind, 2014. "Part-Load Performance of aWet Indirectly Fired Gas Turbine Integrated with an Organic Rankine Cycle Turbogenerator," Energies, MDPI, vol. 7(12), pages 1-23, December.
    17. Kumar, Rajneesh & Goel, Varun & Kumar, Anoop, 2018. "Investigation of heat transfer augmentation and friction factor in triangular duct solar air heater due to forward facing chamfered rectangular ribs: A CFD based analysis," Renewable Energy, Elsevier, vol. 115(C), pages 824-835.
    18. Ismail, Md. Farhad & Hasan, Muhammad Noman & Saha, Suvash C., 2014. "Numerical study of turbulent fluid flow and heat transfer in lateral perforated extended surfaces," Energy, Elsevier, vol. 64(C), pages 632-639.
    19. Sheikholeslami, Mohsen & Gorji-Bandpy, Mofid & Ganji, Davood Domiri, 2015. "Review of heat transfer enhancement methods: Focus on passive methods using swirl flow devices," Renewable and Sustainable Energy Reviews, Elsevier, vol. 49(C), pages 444-469.
    20. Saeed Soltani & Hassan Athari & Marc A. Rosen & Seyed Mohammad Seyed Mahmoudi & Tatiana Morosuk, 2015. "Thermodynamic Analyses of Biomass Gasification Integrated Externally Fired, Post-Firing and Dual-Fuel Combined Cycles," Sustainability, MDPI, vol. 7(2), pages 1-15, January.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:99:y:2012:i:c:p:393-401. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.