IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v16y2023i1p520-d1023144.html
   My bibliography  Save this article

Thermal Energy and Luminosity Characterization of an Advanced Ignition System Using a Non-Intrusive Methodology in an Optically Accessible Calorimeter

Author

Listed:
  • Roberto Martinelli

    (Engineering Department, University of Perugia, Via Goffredo Duranti, 93, 06125 Perugia, Italy)

  • Federico Ricci

    (Engineering Department, University of Perugia, Via Goffredo Duranti, 93, 06125 Perugia, Italy)

  • Gabriele Discepoli

    (DISMI—Department of Sciences and Methods for Engineering, University of Modena and Reggio Emilia, Via Giovanni Amendola, 2, 42122 Reggio Emilia, Italy)

  • Luca Petrucci

    (Engineering Department, University of Perugia, Via Goffredo Duranti, 93, 06125 Perugia, Italy)

  • Stefano Papi

    (Federal-Mogul Powertrain Italy, a Tenneco Group Company, Stabilimento Ignition—Carpi, Via Della Scienza 6/8, 41012 Carpi, Italy)

  • Carlo N. Grimaldi

    (Engineering Department, University of Perugia, Via Goffredo Duranti, 93, 06125 Perugia, Italy)

Abstract

To restrain the environmental impact of modern SI engines, igniters must guarantee stable combustions with low cycle-to-cycle variability in extreme operating conditions (high EGR, ultra-lean), via high energy release in the combustion chamber. The direct measurement of this energy is not trivial and requires a controlled environment. Luminosity detection is a non-intrusive diagnostic technique to indirectly measure the thermal energy released by the discharge on optically accessible apparatus. This work compares energy and luminosity produced by a plasma igniter in a constant volume vessel at realistic working conditions (ignition at 8 bar and air as a medium). A calibration factor can be defined to describe the thermal energy behavior as a function of the discharge luminosity and to give an assessment of such approach for its use in optically accessible engine. This study shows that thermal energy and luminosity are influenced by the gas type and related by a linear relationship for both air and nitrogen. The presence of oxygen resulted in discharges with reduced energy delivery to the medium and a lower discharge luminosity compared to nitrogen. This work outcome could improve the use of a non-intrusive methodology, based on luminosity detection, to characterize the igniter performance, exploitable for 3D-CFD.

Suggested Citation

  • Roberto Martinelli & Federico Ricci & Gabriele Discepoli & Luca Petrucci & Stefano Papi & Carlo N. Grimaldi, 2023. "Thermal Energy and Luminosity Characterization of an Advanced Ignition System Using a Non-Intrusive Methodology in an Optically Accessible Calorimeter," Energies, MDPI, vol. 16(1), pages 1-22, January.
  • Handle: RePEc:gam:jeners:v:16:y:2023:i:1:p:520-:d:1023144
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/16/1/520/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/16/1/520/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Costa, M. & Marchitto, L. & Merola, S.S. & Sorge, U., 2014. "Study of mixture formation and early flame development in a research GDI (gasoline direct injection) engine through numerical simulation and UV-digital imaging," Energy, Elsevier, vol. 77(C), pages 88-96.
    2. Tornatore, Cinzia & Bozza, Fabio & De Bellis, Vincenzo & Teodosio, Luigi & Valentino, Gerardo & Marchitto, Luca, 2019. "Experimental and numerical study on the influence of cooled EGR on knock tendency, performance and emissions of a downsized spark-ignition engine," Energy, Elsevier, vol. 172(C), pages 968-976.
    3. Jeon, Joonho, 2020. "Spatiotemporal flame propagations, combustion and solid particle emissions from lean and stoichiometric gasoline direct injection engine operation," Energy, Elsevier, vol. 210(C).
    4. Karvountzis-Kontakiotis, Apostolos & Vafamehr, Hassan & Cairns, Alasdair & Peckham, Mark, 2018. "Study on pollutants formation under knocking combustion conditions using an optical single cylinder SI research engine," Energy, Elsevier, vol. 158(C), pages 899-910.
    5. Yin, Xiaojun & Sun, Nannan & Sun, Ting & Shen, Hongguang & Mehra, Roopesh Kumar & Liu, Junlong & Wang, Ying & Yang, Bo & Zeng, Ke, 2022. "Experimental investigation the effects of spark discharge characteristics on the heavy-duty spark ignition natural gas engine at low load condition," Energy, Elsevier, vol. 239(PC).
    6. Discepoli, G. & Cruccolini, V. & Ricci, F. & Di Giuseppe, A. & Papi, S. & Grimaldi, C.N., 2020. "Experimental characterisation of the thermal energy released by a Radio-Frequency Corona Igniter in nitrogen and air," Applied Energy, Elsevier, vol. 263(C).
    7. Wei, Haiqiao & Zhang, Ren & Chen, Lin & Pan, Jiaying & Wang, Xuan, 2021. "Effects of high ignition energy on lean combustion characteristics of natural gas using an optical engine with a high compression ratio," Energy, Elsevier, vol. 223(C).
    8. Rocha, Déborah Domingos da & de Castro Radicchi, Fábio & Lopes, Gustavo Santos & Brunocilla, Marcello Francisco & Gomes, Paulo César de Ferreira & Santos, Nathalia Duarte Souza Alvarenga & Malaquias, , 2021. "Study of the water injection control parameters on combustion performance of a spark-ignition engine," Energy, Elsevier, vol. 217(C).
    9. Salvi, B.L. & Subramanian, K.A., 2015. "Experimental investigation and phenomenological model development of flame kernel growth rate in a gasoline fuelled spark ignition engine," Applied Energy, Elsevier, vol. 139(C), pages 93-103.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Liu, Zuowen & Zheng, Zhaolei, 2024. "The effect of ignition energy on the lean combustion limitation in high compression ratio engines," Energy, Elsevier, vol. 301(C).
    2. Marelli, Silvia & Marmorato, Giulio & Capobianco, Massimo, 2016. "Evaluation of heat transfer effects in small turbochargers by theoretical model and its experimental validation," Energy, Elsevier, vol. 112(C), pages 264-272.
    3. Anufriev, I.S. & Kopyev, E.P. & Alekseenko, S.V. & Sharypov, O.V. & Vigriyanov, M.S., 2022. "New ecology safe waste-to-energy technology of liquid fuel combustion with superheated steam," Energy, Elsevier, vol. 250(C).
    4. Liu, Zengbin & Zhen, Xudong & Tian, Zhi & Liu, Daming & Wang, Yang, 2024. "Study on the effect of injection strategy on the combustion and emission characteristics of direct injection spark ignition bio-butanol engine," Energy, Elsevier, vol. 289(C).
    5. Yuan, Zhipeng & Fu, Jianqin & Liu, Qi & Ma, Yinjie & Zhan, Zhangsong, 2018. "Quantitative study on influence factors of power performance of variable valve timing (VVT) engines and correction of its governing equation," Energy, Elsevier, vol. 157(C), pages 314-326.
    6. Xiao, Gang & Jia, Ming & Wang, Tianyou, 2016. "Large eddy simulation of n-heptane spray combustion in partially premixed combustion regime with linear eddy model," Energy, Elsevier, vol. 97(C), pages 20-35.
    7. Naderi, Alireza & Qasemian, Ali & Shojaeefard, Mohammad Hasan & Samiezadeh, Saman & Younesi, Mostafa & Sohani, Ali & Hoseinzadeh, Siamak, 2021. "A smart load-speed sensitive cooling map to have a high- performance thermal management system in an internal combustion engine," Energy, Elsevier, vol. 229(C).
    8. Merola, Simona Silvia & Tornatore, Cinzia & Irimescu, Adrian & Marchitto, Luca & Valentino, Gerardo, 2016. "Optical diagnostics of early flame development in a DISI (direct injection spark ignition) engine fueled with n-butanol and gasoline," Energy, Elsevier, vol. 108(C), pages 50-62.
    9. Duan, Xiongbo & Feng, Lining & Liu, Haibo & Jiang, Pengfei & Chen, Chao & Sun, Zhiqiang, 2023. "Experimental investigation on exhaust emissions of a heavy-duty vehicle powered by a methanol-fuelled spark ignition engine under world Harmonized Transient Cycle and actual on-road driving conditions," Energy, Elsevier, vol. 282(C).
    10. Keskinen, Karri & Kaario, Ossi & Nuutinen, Mika & Vuorinen, Ville & Künsch, Zaira & Liavåg, Lars Ola & Larmi, Martti, 2016. "Mixture formation in a direct injection gas engine: Numerical study on nozzle type, injection pressure and injection timing effects," Energy, Elsevier, vol. 94(C), pages 542-556.
    11. Yin, Xiaojun & Sun, Nannan & Sun, Ting & Shen, Hongguang & Mehra, Roopesh Kumar & Liu, Junlong & Wang, Ying & Yang, Bo & Zeng, Ke, 2022. "Experimental investigation the effects of spark discharge characteristics on the heavy-duty spark ignition natural gas engine at low load condition," Energy, Elsevier, vol. 239(PC).
    12. Hao Chen & Chenxi Wang & Xiang Li & Yongzhi Li & Miao Zhang & Zhijun Peng & Yiqiang Pei & Zhihao Ma & Xuewen Zhang & Peiyong Ni & Rohitha Weerasinghe & Raouf Mobasheri, 2023. "Quantitative Analysis of Water Injection Mass and Timing Effects on Oxy-Fuel Combustion Characteristics in a GDI Engine Fuelled with E10," Sustainability, MDPI, vol. 15(13), pages 1-17, June.
    13. Yang, Jingxun & Xie, Fangxi & Jiang, Beiping & Li, Xiaoping & Su, Yan & Zhang, Hao, 2024. "Influence of structure parameters of pre-chamber on lean combustion of active pre-chamber jet ignition engine," Energy, Elsevier, vol. 304(C).
    14. Galindo, José & Navarro, Roberto & De la Morena, Joaquín & Pitarch, Rafael & Guilain, Stéphane, 2022. "On combustion instability induced by water condensation in a low-pressure exhaust gas recirculation system for spark-ignition engines," Energy, Elsevier, vol. 261(PA).
    15. Ghaderi Masouleh, M. & Keskinen, K. & Kaario, O. & Kahila, H. & Wright, Y.M. & Vuorinen, V., 2018. "Flow and thermal field effects on cycle-to-cycle variation of combustion: scale-resolving simulation in a spark ignited simplified engine configuration," Applied Energy, Elsevier, vol. 230(C), pages 486-505.
    16. Thiago Rodrigo Vieira da Silva & Nilton Antonio Diniz Netto & Jeanine Costa Santos & Augusto Cesar Teixeira Malaquias & José Guilherme Coelho Baêta, 2022. "Development Procedure for Performance Estimation and Main Dimensions Calculation of a Highly-Boosted Ethanol Engine with Water Injection," Energies, MDPI, vol. 15(13), pages 1-24, June.
    17. Federico Ricci & Francesco Mariani & Stefano Papi & Jacopo Zembi & Michele Battistoni & Carlo Nazareno Grimaldi, 2024. "The Synergy between Methanol M100 and Plasma-Assisted Ignition System PAI to Achieve Increasingly Leaner Mixtures in a Single-Cylinder Engine," Energies, MDPI, vol. 17(7), pages 1-14, March.
    18. Yang, Kailin & Wang, Zhongshu & Zhang, Kechao & Wang, Dan & Xie, Fangxi & Xu, Yun & Yang, Kaiqiang, 2023. "Impact of natural gas injection timing on the combustion and emissions performance of a dual-direct-injection diesel/natural gas engine," Energy, Elsevier, vol. 270(C).
    19. Zhang, Zhifei & Li, Tie & Shi, Weiquan, 2019. "Ambient Tracer-LIF for 2-D quantitative measurement of fuel concentration in gas jets," Energy, Elsevier, vol. 171(C), pages 372-384.
    20. Wang, Bin & Xie, Fangxi & Hong, Wei & Du, Jiakun & Chen, Hong & Li, Xiaoping, 2023. "Extending ultra-lean burn performance of high compression ratio pre-chamber jet ignition engines based on injection strategy and optimized structure," Energy, Elsevier, vol. 282(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:16:y:2023:i:1:p:520-:d:1023144. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.