IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i10p2923-d557243.html
   My bibliography  Save this article

Transient Cavitation and Friction-Induced Heating Effects of Diesel Fuel during the Needle Valve Early Opening Stages for Discharge Pressures up to 450 MPa

Author

Listed:
  • Konstantinos Kolovos

    (Department of Mechanical Engineering & Aeronautics, School of Mathematics, Computer Sciences & Engineering, City University of London, London EC1V 0HB, UK)

  • Phoevos Koukouvinis

    (Department of Mechanical Engineering & Aeronautics, School of Mathematics, Computer Sciences & Engineering, City University of London, London EC1V 0HB, UK)

  • Robert M. McDavid

    (Caterpillar Inc., Mossville, IL 61552, USA)

  • Manolis Gavaises

    (Department of Mechanical Engineering & Aeronautics, School of Mathematics, Computer Sciences & Engineering, City University of London, London EC1V 0HB, UK)

Abstract

An investigation of the fuel heating, vapor formation, and cavitation erosion location patterns inside a five-hole common rail diesel fuel injector, occurring during the early opening period of the needle valve (from 2 μm to 80 μm), discharging at pressures of up to 450 MPa, is presented. Numerical simulations were performed using the explicit density-based solver of the compressible Navier–Stokes (NS) and energy conservation equations. The flow solver was combined with tabulated property data for a four-component diesel fuel surrogate, derived from the perturbed chain statistical associating fluid theory (PC-SAFT) equation of state (EoS), which allowed for a significant amount of the fuel’s physical and transport properties to be quantified. The Wall Adapting Local Eddy viscosity (WALE) Large Eddy Simulation (LES) model was used to resolve sub-grid scale turbulence, while a cell-based mesh deformation arbitrary Lagrangian–Eulerian (ALE) formulation was used for modelling the injector’s needle valve movement. Friction-induced heating was found to increase significantly when decreasing the pressure. At the same time, the Joule–Thomson cooling effect was calculated for up to 25 degrees K for the local fuel temperature drop relative to the fuel’s feed temperature. The extreme injection pressures induced fuel jet velocities in the order of 1100 m/s, affecting the formation of coherent vortical flow structures into the nozzle’s sac volume.

Suggested Citation

  • Konstantinos Kolovos & Phoevos Koukouvinis & Robert M. McDavid & Manolis Gavaises, 2021. "Transient Cavitation and Friction-Induced Heating Effects of Diesel Fuel during the Needle Valve Early Opening Stages for Discharge Pressures up to 450 MPa," Energies, MDPI, vol. 14(10), pages 1-18, May.
    • Handle: RePEc:gam:jeners:v:14:y:2021:i:10:p:2923-:d:557243
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/10/2923/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/14/10/2923/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Battistoni, Michele & Grimaldi, Carlo Nazareno, 2012. "Numerical analysis of injector flow and spray characteristics from diesel injectors using fossil and biodiesel fuels," Applied Energy, Elsevier, vol. 97(C), pages 656-666.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Djati Wibowo Djamari & Muhammad Idris & Permana Andi Paristiawan & Muhammad Mujtaba Abbas & Olusegun David Samuel & Manzoore Elahi M. Soudagar & Safarudin Gazali Herawan & Davannendran Chandran & Abdu, 2022. "Diesel Spray: Development of Spray in Diesel Engine," Sustainability, MDPI, vol. 14(23), pages 1-22, November.
    2. M.H.H. Ishak & Farzad Ismail & Sharzali Che Mat & M.Z. Abdullah & M.S. Abdul Aziz & M.Y. Idroas, 2019. "Numerical Analysis of Nozzle Flow and Spray Characteristics from Different Nozzles Using Diesel and Biofuel Blends," Energies, MDPI, vol. 12(2), pages 1-25, January.
    3. Grima-Olmedo, C. & Ramírez-Gómez, Á. & Alcalde-Cartagena, R., 2014. "Energetic performance of landfill and digester biogas in a domestic cooker," Applied Energy, Elsevier, vol. 134(C), pages 301-308.
    4. Haseeb Yaqoob & Yew Heng Teoh & Farooq Sher & Muhammad Umer Farooq & Muhammad Ahmad Jamil & Zareena Kausar & Noor Us Sabah & Muhammad Faizan Shah & Hafiz Zia Ur Rehman & Atiq Ur Rehman, 2021. "Potential of Waste Cooking Oil Biodiesel as Renewable Fuel in Combustion Engines: A Review," Energies, MDPI, vol. 14(9), pages 1-20, April.
    5. Hongzhan Xie & Lanbo Song & Yizhi Xie & Dong Pi & Chunyu Shao & Qizhao Lin, 2015. "An Experimental Study on the Macroscopic Spray Characteristics of Biodiesel and Diesel in a Constant Volume Chamber," Energies, MDPI, vol. 8(6), pages 1-21, June.
    6. Muteeb ul Haq & Ali Turab Jafry & Muhammad Salman Abbasi & Muhammad Jawad & Saad Ahmad & Taqi Ahmad Cheema & Naseem Abbas, 2022. "Numerical and Experimental Spray Analysis of Castor and Jatropha Biodiesel under Non-Evaporating Conditions," Energies, MDPI, vol. 15(20), pages 1-18, October.
    7. Michael Frank & Dimitris Drikakis, 2018. "Draining Water from Aircraft Fuel Using Nitrogen Enriched Air," Energies, MDPI, vol. 11(4), pages 1-16, April.
    8. Luka Lešnik & Breda Kegl & Eloísa Torres-Jiménez & Fernando Cruz-Peragón & Carmen Mata & Ignacijo Biluš, 2021. "Effect of the In-Cylinder Back Pressure on the Injection Process and Fuel Flow Characteristics in a Common-Rail Diesel Injector Using GTL Fuel," Energies, MDPI, vol. 14(2), pages 1-21, January.
    9. Zhang, Ji & Jing, Wei & Roberts, William L. & Fang, Tiegang, 2013. "Soot temperature and KL factor for biodiesel and diesel spray combustion in a constant volume combustion chamber," Applied Energy, Elsevier, vol. 107(C), pages 52-65.
    10. Agarwal, Avinash Kumar & Som, Sibendu & Shukla, Pravesh Chandra & Goyal, Harsh & Longman, Douglas, 2015. "In-nozzle flow and spray characteristics for mineral diesel, Karanja, and Jatropha biodiesels," Applied Energy, Elsevier, vol. 156(C), pages 138-148.
    11. Zhang, Jibao & Zhang, Xin & Wang, Tao & Hou, Xiaosen, 2019. "A numerical study on jet characteristics under different supercritical conditions for engine applications," Applied Energy, Elsevier, vol. 252(C), pages 1-1.
    12. Mohan, Balaji & Yang, Wenming & Yu, Wenbin, 2014. "Effect of internal nozzle flow and thermo-physical properties on spray characteristics of methyl esters," Applied Energy, Elsevier, vol. 129(C), pages 123-134.
    13. Ludovic Lamoot & Brady Manescau & Khaled Chetehouna & Nicolas Gascoin, 2021. "Review on the Effect of the Phenomenon of Cavitation in Combustion Efficiency and the Role of Biofuels as a Solution against Cavitation," Energies, MDPI, vol. 14(21), pages 1-35, November.
    14. Ferrari, A. & Mittica, A., 2012. "FEM modeling of the piezoelectric driving system in the design of direct-acting diesel injectors," Applied Energy, Elsevier, vol. 99(C), pages 471-483.
    15. L. Kevorkijan & A. Palomar-Torres & E. Torres-Jiménez & C. Mata & I. Biluš & L. Lešnik, 2023. "Obtaining the Synthetic Fuels from Waste Plastic and Their Effect on Cavitation Formation in a Common-Rail Diesel Injector," Sustainability, MDPI, vol. 15(21), pages 1-22, October.
    16. Yesilyurt, Murat Kadir, 2019. "The effects of the fuel injection pressure on the performance and emission characteristics of a diesel engine fuelled with waste cooking oil biodiesel-diesel blends," Renewable Energy, Elsevier, vol. 132(C), pages 649-666.
    17. Yang, S.I. & Hsu, T.C. & Wu, M.S., 2016. "Spray combustion characteristics of kerosene/bio-oil part II: Numerical study," Energy, Elsevier, vol. 115(P1), pages 458-467.
    18. Moon, Seoksu & Li, Tianyun & Sato, Kiyotaka & Yokohata, Hideaki, 2017. "Governing parameters and dynamics of turbulent spray atomization from modern GDI injectors," Energy, Elsevier, vol. 127(C), pages 89-100.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:10:p:2923-:d:557243. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.