IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v11y2018i4p908-d140774.html
   My bibliography  Save this article

Draining Water from Aircraft Fuel Using Nitrogen Enriched Air

Author

Listed:
  • Michael Frank

    (Department of Mechanical Aerospace and Engineering, University of Strathclyde, 75 Montrose, Glasgow G11XJ, UK)

  • Dimitris Drikakis

    (Department of Mechanical Aerospace and Engineering, University of Strathclyde, 75 Montrose, Glasgow G11XJ, UK)

Abstract

This paper concerns a computational study of the process of removing water from an aircraft’s fuel tank by pumping nitrogen enriched air (NEA) from the bottom of the tank. This is an important procedure for the smooth, efficient, and safe operation of the aircraft’s engine. Due to the low partial pressure of water in the pumped NEA, it absorbs water from the fuel. The water-laden bubbles enter the ullage, the empty space above the fuel, and escape into the environment. The effects of the number of NEA inlets and the NEA mass flow rate on the timescale of the NEA pumping were investigated using Computational Fluid Dynamics. The results reveal that the absorption of water by the NEA bubbles is low and is not affected by the number of the inlets used. Yet, the water content in the fuel decreases fast during the procedure, which is the desired outcome. We show that this is due to the relatively dry NEA entering the ullage and displacing the moist air, thus reducing the partial pressure of water at the fuel/ullage interface. This shift from equilibrium conditions forces water to evaporate from the fuel’s entire surface. Furthermore, the amount of water migrating from the fuel directly into the ullage is significantly greater than that absorbed by the rising bubbles. In turn, the rate of decrease of the water content in the ullage is determined by the total NEA mass flow rate and this is the dominant contributor to the draining time, with the number of NEA nozzles playing a minor role. We confirmed this by pumping NEA directly into the ullage, where we observe a significant decrease of water even when the NEA is not pumped through the fuel. We also show that doubling the mass flow rate halves the draining time. When considering the capability of most modern aircraft to pump NEA through the fuel as part of their inerting system, the proposed method for removing water is particularly attractive, requiring very little (if at all) design modification.

Suggested Citation

  • Michael Frank & Dimitris Drikakis, 2018. "Draining Water from Aircraft Fuel Using Nitrogen Enriched Air," Energies, MDPI, vol. 11(4), pages 1-16, April.
  • Handle: RePEc:gam:jeners:v:11:y:2018:i:4:p:908-:d:140774
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/11/4/908/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/11/4/908/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Battistoni, Michele & Grimaldi, Carlo Nazareno, 2012. "Numerical analysis of injector flow and spray characteristics from diesel injectors using fossil and biodiesel fuels," Applied Energy, Elsevier, vol. 97(C), pages 656-666.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Djati Wibowo Djamari & Muhammad Idris & Permana Andi Paristiawan & Muhammad Mujtaba Abbas & Olusegun David Samuel & Manzoore Elahi M. Soudagar & Safarudin Gazali Herawan & Davannendran Chandran & Abdu, 2022. "Diesel Spray: Development of Spray in Diesel Engine," Sustainability, MDPI, vol. 14(23), pages 1-22, November.
    2. M.H.H. Ishak & Farzad Ismail & Sharzali Che Mat & M.Z. Abdullah & M.S. Abdul Aziz & M.Y. Idroas, 2019. "Numerical Analysis of Nozzle Flow and Spray Characteristics from Different Nozzles Using Diesel and Biofuel Blends," Energies, MDPI, vol. 12(2), pages 1-25, January.
    3. Grima-Olmedo, C. & Ramírez-Gómez, Á. & Alcalde-Cartagena, R., 2014. "Energetic performance of landfill and digester biogas in a domestic cooker," Applied Energy, Elsevier, vol. 134(C), pages 301-308.
    4. Haseeb Yaqoob & Yew Heng Teoh & Farooq Sher & Muhammad Umer Farooq & Muhammad Ahmad Jamil & Zareena Kausar & Noor Us Sabah & Muhammad Faizan Shah & Hafiz Zia Ur Rehman & Atiq Ur Rehman, 2021. "Potential of Waste Cooking Oil Biodiesel as Renewable Fuel in Combustion Engines: A Review," Energies, MDPI, vol. 14(9), pages 1-20, April.
    5. Konstantinos Kolovos & Phoevos Koukouvinis & Robert M. McDavid & Manolis Gavaises, 2021. "Transient Cavitation and Friction-Induced Heating Effects of Diesel Fuel during the Needle Valve Early Opening Stages for Discharge Pressures up to 450 MPa," Energies, MDPI, vol. 14(10), pages 1-18, May.
    6. Hongzhan Xie & Lanbo Song & Yizhi Xie & Dong Pi & Chunyu Shao & Qizhao Lin, 2015. "An Experimental Study on the Macroscopic Spray Characteristics of Biodiesel and Diesel in a Constant Volume Chamber," Energies, MDPI, vol. 8(6), pages 1-21, June.
    7. Muteeb ul Haq & Ali Turab Jafry & Muhammad Salman Abbasi & Muhammad Jawad & Saad Ahmad & Taqi Ahmad Cheema & Naseem Abbas, 2022. "Numerical and Experimental Spray Analysis of Castor and Jatropha Biodiesel under Non-Evaporating Conditions," Energies, MDPI, vol. 15(20), pages 1-18, October.
    8. Luka Lešnik & Breda Kegl & Eloísa Torres-Jiménez & Fernando Cruz-Peragón & Carmen Mata & Ignacijo Biluš, 2021. "Effect of the In-Cylinder Back Pressure on the Injection Process and Fuel Flow Characteristics in a Common-Rail Diesel Injector Using GTL Fuel," Energies, MDPI, vol. 14(2), pages 1-21, January.
    9. Zhang, Ji & Jing, Wei & Roberts, William L. & Fang, Tiegang, 2013. "Soot temperature and KL factor for biodiesel and diesel spray combustion in a constant volume combustion chamber," Applied Energy, Elsevier, vol. 107(C), pages 52-65.
    10. Agarwal, Avinash Kumar & Som, Sibendu & Shukla, Pravesh Chandra & Goyal, Harsh & Longman, Douglas, 2015. "In-nozzle flow and spray characteristics for mineral diesel, Karanja, and Jatropha biodiesels," Applied Energy, Elsevier, vol. 156(C), pages 138-148.
    11. Zhang, Jibao & Zhang, Xin & Wang, Tao & Hou, Xiaosen, 2019. "A numerical study on jet characteristics under different supercritical conditions for engine applications," Applied Energy, Elsevier, vol. 252(C), pages 1-1.
    12. Mohan, Balaji & Yang, Wenming & Yu, Wenbin, 2014. "Effect of internal nozzle flow and thermo-physical properties on spray characteristics of methyl esters," Applied Energy, Elsevier, vol. 129(C), pages 123-134.
    13. Ludovic Lamoot & Brady Manescau & Khaled Chetehouna & Nicolas Gascoin, 2021. "Review on the Effect of the Phenomenon of Cavitation in Combustion Efficiency and the Role of Biofuels as a Solution against Cavitation," Energies, MDPI, vol. 14(21), pages 1-35, November.
    14. Ferrari, A. & Mittica, A., 2012. "FEM modeling of the piezoelectric driving system in the design of direct-acting diesel injectors," Applied Energy, Elsevier, vol. 99(C), pages 471-483.
    15. L. Kevorkijan & A. Palomar-Torres & E. Torres-Jiménez & C. Mata & I. Biluš & L. Lešnik, 2023. "Obtaining the Synthetic Fuels from Waste Plastic and Their Effect on Cavitation Formation in a Common-Rail Diesel Injector," Sustainability, MDPI, vol. 15(21), pages 1-22, October.
    16. Yesilyurt, Murat Kadir, 2019. "The effects of the fuel injection pressure on the performance and emission characteristics of a diesel engine fuelled with waste cooking oil biodiesel-diesel blends," Renewable Energy, Elsevier, vol. 132(C), pages 649-666.
    17. Yang, S.I. & Hsu, T.C. & Wu, M.S., 2016. "Spray combustion characteristics of kerosene/bio-oil part II: Numerical study," Energy, Elsevier, vol. 115(P1), pages 458-467.
    18. Moon, Seoksu & Li, Tianyun & Sato, Kiyotaka & Yokohata, Hideaki, 2017. "Governing parameters and dynamics of turbulent spray atomization from modern GDI injectors," Energy, Elsevier, vol. 127(C), pages 89-100.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:11:y:2018:i:4:p:908-:d:140774. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.