IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v331y2023ics0306261922016750.html
   My bibliography  Save this article

Ceramic nanoparticles enhancement of latent heat thermal energy storage properties for LiNO3/NaCl: Evaluation from material to system level

Author

Listed:
  • Luo, Qingyang
  • Liu, Xianglei
  • Xu, Qiao
  • Tian, Yang
  • Yao, Haichen
  • Wang, Jianguo
  • Lv, Shushan
  • Dang, Chunzhuo
  • Xuan, Yimin

Abstract

Focusing on the development of the next generation latent heat thermal energy storage (TES), molten salt is one of the most promising candidates, while it suffers from small thermal charging rate and low energy storage density. Adding ceramic nanoparticles (NPs) with high thermal conductivity and high chemical stabilities has been proposed to alleviate above problems. However, it’s very challenging to enhance both thermal conductivity and specific heat capacity (Cp) simultaneously. Besides, induced viscosity increment by NPs will instead reduce the thermal charging rate of TES system, due to suppressed natural convection of molten salts. Herein, concurrent enhancement in solidus thermal conductivity and Cp is demonstrated by doping MgO NPs into LiNO3/NaCl, which are improved by 63.5 % and 32.3 % at 4 wt%, respectively. The underlying mechanism is attributed to very low interfacial thermal resistance (Rb = 2.424 × 10−9 K·m2·W−1) between MgO and LiNO3/NaCl. Benefiting from enhanced Cp, the total energy storage density increases from 662.9 J·g−1 to 671.7 J·g−1 for temperature range of 50–300 °C despite decreased phase change enthalpy. The viscosity has a sharp increase from 4.2 cP to 22.4 cP when NPs concentration rises from 0 wt% to 10 wt% at 360 °C. When being applied in TES system, the optimal concentration of MgO NPs is found to be 4 wt%. The thermal charging rate of TES system is suppressed when NPs concentration is too low or too high due to limited thermal conduction and inhibited natural convection, respectively. Viscosity is verified as important as thermal conductivity in system level evaluation. This work helps to guide the design of high-performance molten salts in TES system, so as to achieve both faster thermal charging rate and higher energy storage density.

Suggested Citation

  • Luo, Qingyang & Liu, Xianglei & Xu, Qiao & Tian, Yang & Yao, Haichen & Wang, Jianguo & Lv, Shushan & Dang, Chunzhuo & Xuan, Yimin, 2023. "Ceramic nanoparticles enhancement of latent heat thermal energy storage properties for LiNO3/NaCl: Evaluation from material to system level," Applied Energy, Elsevier, vol. 331(C).
    • Handle: RePEc:eee:appene:v:331:y:2023:i:c:s0306261922016750
    DOI: 10.1016/j.apenergy.2022.120418
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261922016750
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2022.120418?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Muñoz-Sánchez, Belén & Nieto-Maestre, Javier & Iparraguirre-Torres, Iñigo & García-Romero, Ana & Sala-Lizarraga, Jose M., 2018. "Molten salt-based nanofluids as efficient heat transfer and storage materials at high temperatures. An overview of the literature," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 3924-3945.
    2. Li, Qi & Li, Chuan & Du, Zheng & Jiang, Feng & Ding, Yulong, 2019. "A review of performance investigation and enhancement of shell and tube thermal energy storage device containing molten salt based phase change materials for medium and high temperature applications," Applied Energy, Elsevier, vol. 255(C).
    3. Yu, Yinsheng & Zhao, Chenyang & Tao, Yubing & Chen, Xi & He, Ya-Ling, 2021. "Superior thermal energy storage performance of NaCl-SWCNT composite phase change materials: A molecular dynamics approach," Applied Energy, Elsevier, vol. 290(C).
    4. Jeffrey D. Sachs & Guido Schmidt-Traub & Mariana Mazzucato & Dirk Messner & Nebojsa Nakicenovic & Johan Rockström, 2019. "Six Transformations to achieve the Sustainable Development Goals," Nature Sustainability, Nature, vol. 2(9), pages 805-814, September.
    5. Vignarooban, K. & Xu, Xinhai & Arvay, A. & Hsu, K. & Kannan, A.M., 2015. "Heat transfer fluids for concentrating solar power systems – A review," Applied Energy, Elsevier, vol. 146(C), pages 383-396.
    6. Alva, Guruprasad & Liu, Lingkun & Huang, Xiang & Fang, Guiyin, 2017. "Thermal energy storage materials and systems for solar energy applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 68(P1), pages 693-706.
    7. Ding, Jing & Pan, Gechuanqi & Du, Lichan & Lu, Jianfeng & Wang, Weilong & Wei, Xiaolan & Li, Jiang, 2018. "Molecular dynamics simulations of the local structures and transport properties of Na2CO3 and K2CO3," Applied Energy, Elsevier, vol. 227(C), pages 555-563.
    8. Jankowski, Nicholas R. & McCluskey, F. Patrick, 2014. "A review of phase change materials for vehicle component thermal buffering," Applied Energy, Elsevier, vol. 113(C), pages 1525-1561.
    9. Ying, Xuchen & Huang, Weijia & Liu, Wenhua & Liu, Guiliang & Li, Jun & Yang, Mo, 2022. "Asymmetric phenomenon of flow and heat transfer in charging process of thermal energy storage based on an entire domain model," Applied Energy, Elsevier, vol. 316(C).
    10. Lin, Yaxue & Jia, Yuting & Alva, Guruprasad & Fang, Guiyin, 2018. "Review on thermal conductivity enhancement, thermal properties and applications of phase change materials in thermal energy storage," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 2730-2742.
    11. Raud, Ralf & Jacob, Rhys & Bruno, Frank & Will, Geoffrey & Steinberg, Theodore A., 2017. "A critical review of eutectic salt property prediction for latent heat energy storage systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 70(C), pages 936-944.
    12. Yang, Xiaohu & Yu, Jiabang & Guo, Zengxu & Jin, Liwen & He, Ya-Ling, 2019. "Role of porous metal foam on the heat transfer enhancement for a thermal energy storage tube," Applied Energy, Elsevier, vol. 239(C), pages 142-156.
    13. Luo, Qingyang & Liu, Xianglei & Wang, Haolei & Xu, Qiao & Tian, Yang & Liang, Ting & Liu, Qibin & Liu, Zhan & Yang, Xiaohu & Xuan, Yimin & Li, Yongliang & Ding, Yulong, 2022. "Synergetic enhancement of heat storage density and heat transport ability of phase change materials inlaid in 3D hierarchical ceramics," Applied Energy, Elsevier, vol. 306(PA).
    14. Ding, Jing & Du, Lichan & Pan, Gechuanqi & Lu, Jianfeng & Wei, Xiaolan & Li, Jiang & Wang, Weilong & Yan, Jinyue, 2018. "Molecular dynamics simulations of the local structures and thermodynamic properties on molten alkali carbonate K2CO3," Applied Energy, Elsevier, vol. 220(C), pages 536-544.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Yao, Haichen & Liu, Xianglei & Li, Jiawei & Luo, Qingyang & Tian, Yang & Xuan, Yimin, 2023. "Chloroplast-granum inspired phase change capsules accelerate energy storage of packed-bed thermal energy storage system," Energy, Elsevier, vol. 284(C).
    2. Wu, Chunlei & Wang, Qing & Wang, Xinmin & Sun, Shipeng & Bai, Jingru & Cui, Da & Pan, Shuo & Sheng, Hongyu, 2024. "Effect of Al2O3 nanoparticle dispersion on the thermal properties of a eutectic salt for solar power applications: Experimental and molecular simulation studies," Energy, Elsevier, vol. 288(C).
    3. Liu, Xianglei & Ni, Renzhong & Tian, Yang & Yao, Haichen & Xu, Qiao & Xuan, Yimin, 2023. "Environment-friendly efficient thermal energy storage paradigm based on sugarcane-derived eco-ceramics phase change composites: From material to device," Renewable Energy, Elsevier, vol. 217(C).
    4. Wu, Chunlei & Wang, Qing & Wang, Xinmin & Sun, Shipeng & Wang, Yuqi & Wu, Shuang & Bai, Jingru & Sheng, Hongyu & Zhang, Jinghui, 2024. "Al2O3 nanoparticles integration for comprehensive enhancement of eutectic salt thermal performance: Experimental design, molecular dynamics calculations, and system simulation studies," Energy, Elsevier, vol. 292(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Luo, Qingyang & Liu, Xianglei & Wang, Haolei & Xu, Qiao & Tian, Yang & Liang, Ting & Liu, Qibin & Liu, Zhan & Yang, Xiaohu & Xuan, Yimin & Li, Yongliang & Ding, Yulong, 2022. "Synergetic enhancement of heat storage density and heat transport ability of phase change materials inlaid in 3D hierarchical ceramics," Applied Energy, Elsevier, vol. 306(PA).
    2. Li, Zhi & Lu, Yiji & Huang, Rui & Chang, Jinwei & Yu, Xiaonan & Jiang, Ruicheng & Yu, Xiaoli & Roskilly, Anthony Paul, 2021. "Applications and technological challenges for heat recovery, storage and utilisation with latent thermal energy storage," Applied Energy, Elsevier, vol. 283(C).
    3. Adrián Caraballo & Santos Galán-Casado & Ángel Caballero & Sara Serena, 2021. "Molten Salts for Sensible Thermal Energy Storage: A Review and an Energy Performance Analysis," Energies, MDPI, vol. 14(4), pages 1-15, February.
    4. Costa, Sol Carolina & Kenisarin, Murat, 2022. "A review of metallic materials for latent heat thermal energy storage: Thermophysical properties, applications, and challenges," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    5. Haiming Long & Yunkun Lu & Liang Chang & Haifeng Zhang & Jingcen Zhang & Gaoqun Zhang & Junjie Hao, 2022. "Molecular Dynamics Simulation of Thermophysical Properties and the Microstructure of Na 2 CO 3 Heat Storage Materials," Energies, MDPI, vol. 15(19), pages 1-13, September.
    6. Liu, Yilin & Cui, Xin & Yan, Weichao & Wang, Jiawei & Su, Jincai & Jin, Liwen, 2022. "A molecular level based parametric study of transport behavior in different polymer composite membranes for water vapor separation," Applied Energy, Elsevier, vol. 326(C).
    7. Alva, Guruprasad & Lin, Yaxue & Fang, Guiyin, 2018. "An overview of thermal energy storage systems," Energy, Elsevier, vol. 144(C), pages 341-378.
    8. Giovanni Salvatore Sau & Valerio Tripi & Anna Chiara Tizzoni & Raffaele Liberatore & Emiliana Mansi & Annarita Spadoni & Natale Corsaro & Mauro Capocelli & Tiziano Delise & Anna Della Libera, 2021. "High-Temperature Chloride-Carbonate Phase Change Material: Thermal Performances and Modelling of a Packed Bed Storage System for Concentrating Solar Power Plants," Energies, MDPI, vol. 14(17), pages 1-17, August.
    9. Liu, Jinjin & Xiao, Xin, 2023. "Molecular dynamics investigation of thermo-physical properties of molten salt with nanoparticles for solar energy application," Energy, Elsevier, vol. 282(C).
    10. Saranprabhu, M.K. & Rajan, K.S., 2019. "Magnesium oxide nanoparticles dispersed solar salt with improved solid phase thermal conductivity and specific heat for latent heat thermal energy storage," Renewable Energy, Elsevier, vol. 141(C), pages 451-459.
    11. Ruan, Zhao-Hui & Gao, Peng & Yuan, Yuan & Tan, He-Ping, 2022. "Theoretical estimation of temperature-dependent radiation properties of molten solar salt using molecular dynamics and first principles," Energy, Elsevier, vol. 246(C).
    12. Nunes, V.M.B. & Lourenço, M.J.V. & Santos, F.J.V. & Nieto de Castro, C.A., 2019. "Molten alkali carbonates as alternative engineering fluids for high temperature applications," Applied Energy, Elsevier, vol. 242(C), pages 1626-1633.
    13. Vigneshwaran, K. & Sodhi, Gurpreet Singh & Muthukumar, P. & Guha, Anurag & Senthilmurugan, S., 2019. "Experimental and numerical investigations on high temperature cast steel based sensible heat storage system," Applied Energy, Elsevier, vol. 251(C), pages 1-1.
    14. Chen, Xue & Li, Xiaolei & Xia, Xinlin & Sun, Chuang & Liu, Rongqiang, 2021. "Thermal storage analysis of a foam-filled PCM heat exchanger subjected to fluctuating flow conditions," Energy, Elsevier, vol. 216(C).
    15. Wu, Shaofei & Yan, Ting & Kuai, Zihan & Pan, Weiguo, 2020. "Preparation and thermal property analysis of a novel phase change heat storage material," Renewable Energy, Elsevier, vol. 150(C), pages 1057-1065.
    16. Xue, Xue & Liu, Xiang & Zhu, Yifan & Yuan, Lei & Zhu, Ying & Jin, Kelang & Zhang, Lei & Zhou, Hao, 2023. "Numerical modeling and parametric study of the heat storage process of the 1.05 MW molten salt furnace," Energy, Elsevier, vol. 282(C).
    17. Liu, Yang & Zheng, Ruowei & Li, Ji, 2022. "High latent heat phase change materials (PCMs) with low melting temperature for thermal management and storage of electronic devices and power batteries: Critical review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 168(C).
    18. Xue Chen & Xiaolei Li & Xinlin Xia & Chuang Sun & Rongqiang Liu, 2019. "Thermal Performance of a PCM-Based Thermal Energy Storage with Metal Foam Enhancement," Energies, MDPI, vol. 12(17), pages 1-18, August.
    19. Hamidi, E. & Ganesan, P.B. & Sharma, R.K. & Yong, K.W., 2023. "Computational study of heat transfer enhancement using porous foams with phase change materials: A comparative review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 176(C).
    20. Wang, Wei & He, Xibo & Shuai, Yong & Qiu, Jun & Hou, Yicheng & Pan, Qinghui, 2022. "Experimental study on thermal performance of a novel medium-high temperature packed-bed latent heat storage system containing binary nitrate," Applied Energy, Elsevier, vol. 309(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:331:y:2023:i:c:s0306261922016750. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.