IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v51y2013icp267-272.html
   My bibliography  Save this article

Experiment of catalyst activity distribution effect on methanol steam reforming performance in the packed bed plate-type reactor

Author

Listed:
  • Wang, Guoqiang
  • Wang, Feng
  • Li, Longjian
  • Zhang, Guofu

Abstract

Methanol reforming is considered as a promising candidate for hydrogen production because of its advantages in many ways. Conventional reformers of packed-bed catalyst suffer from severe limitations of mass and heat transfer. These disadvantages result in a low catalyst effectiveness factor in the conventional pellet catalyst. In this work, a plate-type reactor has been developed to investigate the influence of catalyst activity distribution on methanol steam reforming. Cold spot temperature differences are observed in the temperature profile along the reactor axis. It has been experimentally verified that reducing cold spot temperature differences contributes to the improvement of the catalytic hydrogen production. The minimal cold spot temperature difference is obtained on the optimal catalyst distribution. It is found that the optimal catalyst distribution shows superiority in the methanol conversion and H2 production rate in comparison to that of the other ones.

Suggested Citation

  • Wang, Guoqiang & Wang, Feng & Li, Longjian & Zhang, Guofu, 2013. "Experiment of catalyst activity distribution effect on methanol steam reforming performance in the packed bed plate-type reactor," Energy, Elsevier, vol. 51(C), pages 267-272.
    • Handle: RePEc:eee:energy:v:51:y:2013:i:c:p:267-272
    DOI: 10.1016/j.energy.2012.12.027
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544212009541
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2012.12.027?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Kim, Tae-Soo & Song, Soonho & Chun, Kwang-Min & Lee, Sang Hun, 2010. "An experimental study of syn-gas production via microwave plasma reforming of methane, iso-octane and gasoline," Energy, Elsevier, vol. 35(6), pages 2734-2743.
    2. Clausen, Lasse R. & Houbak, Niels & Elmegaard, Brian, 2010. "Technoeconomic analysis of a methanol plant based on gasification of biomass and electrolysis of water," Energy, Elsevier, vol. 35(5), pages 2338-2347.
    3. Riaza, J. & Álvarez, L. & Gil, M.V. & Pevida, C. & Pis, J.J. & Rubiera, F., 2011. "Effect of oxy-fuel combustion with steam addition on coal ignition and burnout in an entrained flow reactor," Energy, Elsevier, vol. 36(8), pages 5314-5319.
    4. Singh, M.C. & Garg, S.N., 2009. "Energy rating of different glazings for Indian climates," Energy, Elsevier, vol. 34(11), pages 1986-1992.
    5. El-Sebaii, A.A. & Al-Snani, H., 2010. "Effect of selective coating on thermal performance of flat plate solar air heaters," Energy, Elsevier, vol. 35(4), pages 1820-1828.
    6. Chippar, Purushothama & Ko, Johan & Ju, Hyunchul, 2010. "A global transient, one-dimensional, two-phase model for direct methanol fuel cells (DMFCs) – Part II: Analysis of the time-dependent thermal behavior of DMFCs," Energy, Elsevier, vol. 35(5), pages 2301-2308.
    7. Gutiérrez Ortiz, F.J. & Ollero, P. & Serrera, A. & Galera, S., 2012. "Process integration and exergy analysis of the autothermal reforming of glycerol using supercritical water," Energy, Elsevier, vol. 42(1), pages 192-203.
    8. Wijaya, Willy Yanto & Kawasaki, Shunsuke & Watanabe, Hirotatsu & Okazaki, Ken, 2012. "Damköhler number as a descriptive parameter in methanol steam reforming and its integration with absorption heat pump system," Applied Energy, Elsevier, vol. 94(C), pages 141-147.
    9. Yang, Yoon-Cheol & Lee, Bong-Ju & Chun, Young-Nam, 2009. "Characteristics of methane reforming using gliding arc reactor," Energy, Elsevier, vol. 34(2), pages 172-177.
    10. Rahimpour, M.R. & Mirvakili, A. & Paymooni, K., 2011. "A novel water perm-selective membrane dual-type reactor concept for Fischer–Tropsch synthesis of GTL (gas to liquid) technology," Energy, Elsevier, vol. 36(2), pages 1223-1235.
    11. Wang, Ze & Lin, Weigang & Song, Wenli & Wu, Xuexing, 2012. "Pyrolysis of the lignocellulose fermentation residue by fixed-bed micro reactor," Energy, Elsevier, vol. 43(1), pages 301-305.
    12. Halmann, M. & Frei, A. & Steinfeld, A., 2007. "Carbothermal reduction of alumina: Thermochemical equilibrium calculations and experimental investigation," Energy, Elsevier, vol. 32(12), pages 2420-2427.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Perng, Shiang-Wuu & Chien, Tsai-Chieh & Horng, Rong-Fang & Wu, Horng-Wen, 2019. "Performance enhancement of a plate methanol steam reformer by ribs installed in the reformer channel," Energy, Elsevier, vol. 167(C), pages 588-601.
    2. Lesmana, Donny & Wu, Ho-Shing, 2014. "Modified oxalic acid co-precipitation method for preparing Cu/ZnO/Al2O3/Cr2O3/CeO2 catalysts for the OR (oxidative reforming) of M (methanol) to produce H2 (hydrogen) gas," Energy, Elsevier, vol. 69(C), pages 769-777.
    3. Zhang, Huajing & Xu, Chao & Yu, Hangyu & Wu, Hao & Jin, Fei & Xiao, Feng & Liao, Zhirong, 2022. "Enhancement of methanol steam reforming in a tubular fixed-bed reactor with simultaneous heating inside and outside," Energy, Elsevier, vol. 254(PB).
    4. Perng, Shiang-Wuu & Wu, Horng-Wen, 2023. "Enhancement of proton exchange membrane fuel cell net electric power and methanol-reforming performance by vein channel carved into the reactor plate," Energy, Elsevier, vol. 281(C).
    5. Wang, Feng & Cao, Yiding & Wang, Guoqiang, 2015. "Thermoelectric generation coupling methanol steam reforming characteristic in microreactor," Energy, Elsevier, vol. 80(C), pages 642-653.
    6. Cheng, Chin-Hsiang & Huang, Yu-Xian & King, Shun-Chih & Lee, Chun-I & Leu, Chih-Hsing, 2014. "CFD (computational fluid dynamics)-based optimal design of a micro-reformer by integrating computational a fluid dynamics code using a simplified conjugate-gradient method," Energy, Elsevier, vol. 70(C), pages 355-365.
    7. Li, Lin & Tang, Dawei & Song, Yongchen & Jiang, Bo & Zhang, Qian, 2018. "Hydrogen production from ethanol steam reforming on Ni-Ce/MMT catalysts," Energy, Elsevier, vol. 149(C), pages 937-943.
    8. Ouyang, Kwan & Wu, Horng-Wen & Huang, Shun-Chieh & Wu, Sheng-Ju, 2017. "Optimum parameter design for performance of methanol steam reformer combining Taguchi method with artificial neural network and genetic algorithm," Energy, Elsevier, vol. 138(C), pages 446-458.
    9. Liu, Yangxu & Zhou, Wei & Lin, Yu & Chen, Lu & Chu, Xuyang & Zheng, Tianqing & Wan, Shaolong & Lin, Jingdong, 2019. "Novel copper foam with ordered hole arrays as catalyst support for methanol steam reforming microreactor," Applied Energy, Elsevier, vol. 246(C), pages 24-37.
    10. Inbamrung, Piyanut & Sornchamni, Thana & Prapainainar, Chaiwat & Tungkamani, Sabaithip & Narataruksa, Phavanee & Jovanovic, Goran N., 2018. "Modeling of a square channel monolith reactor for methane steam reforming," Energy, Elsevier, vol. 152(C), pages 383-400.
    11. Wang, Qing-Hui & Yang, Song & Zhou, Wei & Li, Jing-Rong & Xu, Zhi-Jia & Ke, Yu-Zhi & Yu, Wei & Hu, Guang-Hua, 2018. "Optimizing the porosity configuration of porous copper fiber sintered felt for methanol steam reforming micro-reactor based on flow distribution," Applied Energy, Elsevier, vol. 216(C), pages 243-261.
    12. Yao, Ling & Wang, Feng & Wang, Long & Wang, Guoqiang, 2019. "Transport enhancement study on small-scale methanol steam reforming reactor with waste heat recovery for hydrogen production," Energy, Elsevier, vol. 175(C), pages 986-997.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Sergio L. González-González & Ana Tejero-González & Francisco J. Rey-Martínez & Manuel Andrés-Chicote, 2017. "Alternative for Summer Use of Solar Air Heaters in Existing Buildings," Energies, MDPI, vol. 10(7), pages 1-15, July.
    2. Zhen, Xudong & Wang, Yang, 2013. "Study of ignition in a high compression ratio SI (spark ignition) methanol engine using LES (large eddy simulation) with detailed chemical kinetics," Energy, Elsevier, vol. 59(C), pages 549-558.
    3. Zhang, Hanfei & Wang, Ligang & Pérez-Fortes, Mar & Van herle, Jan & Maréchal, François & Desideri, Umberto, 2020. "Techno-economic optimization of biomass-to-methanol with solid-oxide electrolyzer," Applied Energy, Elsevier, vol. 258(C).
    4. Manju Dhakad Tanwar & Felipe Andrade Torres & Ali Mubarak Alqahtani & Pankaj Kumar Tanwar & Yashas Bhand & Omid Doustdar, 2023. "Promising Bioalcohols for Low-Emission Vehicles," Energies, MDPI, vol. 16(2), pages 1-22, January.
    5. Jiang, Chunlong & Lin, Qizhao & Wang, Chengxin & Jiang, Xuedan & Bi, Haobo & Bao, Lin, 2020. "Experimental study of the ignition and combustion characteristics of cattle manure under different environmental conditions," Energy, Elsevier, vol. 197(C).
    6. Díez, Luis I. & García-Mariaca, Alexander & Canalís, Paula & Llera, Eva, 2023. "Oxy-combustion characteristics of torrefied biomass and blends under O2/N2, O2/CO2 and O2/CO2/H2O atmospheres," Energy, Elsevier, vol. 284(C).
    7. Adnan, Muflih A. & Hossain, Mohammad M. & Kibria, Md Golam, 2020. "Biomass upgrading to high-value chemicals via gasification and electrolysis: A thermodynamic analysis," Renewable Energy, Elsevier, vol. 162(C), pages 1367-1379.
    8. Yadav, Deepak & Banerjee, Rangan, 2022. "Thermodynamic and economic analysis of the solar carbothermal and hydrometallurgy routes for zinc production," Energy, Elsevier, vol. 247(C).
    9. Álvarez, L. & Gharebaghi, M. & Jones, J.M. & Pourkashanian, M. & Williams, A. & Riaza, J. & Pevida, C. & Pis, J.J. & Rubiera, F., 2013. "CFD modeling of oxy-coal combustion: Prediction of burnout, volatile and NO precursors release," Applied Energy, Elsevier, vol. 104(C), pages 653-665.
    10. Fang, Shuo & Zhang, Yufeng & Zou, Yuezhang & Sang, Shengtian & Liu, Xiaowei, 2017. "Structural design and analysis of a passive DMFC supplied with concentrated methanol solution," Energy, Elsevier, vol. 128(C), pages 50-61.
    11. Li, Chunlin & Xu, Hengyong & Hou, Shoufu & Sun, Jian & Meng, Fanqiong & Ma, Junguo & Tsubaki, Noritatsu, 2013. "SiC foam monolith catalyst for pressurized adiabatic methane reforming," Applied Energy, Elsevier, vol. 107(C), pages 297-303.
    12. Yuan, Zhenyu & Zhang, Manna & Zuo, Kaiyuan & Ren, Yongqiang, 2018. "The effect of gravity on inner transport and cell performance in passive micro direct methanol fuel cell," Energy, Elsevier, vol. 150(C), pages 28-37.
    13. Mohammadi, K. & Sabzpooshani, M., 2013. "Comprehensive performance evaluation and parametric studies of single pass solar air heater with fins and baffles attached over the absorber plate," Energy, Elsevier, vol. 57(C), pages 741-750.
    14. Li, Yan & Feng, Yanhui & Zhang, Xinxin & Wu, Chuansong, 2014. "Energy propagation in plasma arc welding with keyhole tracking," Energy, Elsevier, vol. 64(C), pages 1044-1056.
    15. Olateju, Babatunde & Kumar, Amit, 2011. "Hydrogen production from wind energy in Western Canada for upgrading bitumen from oil sands," Energy, Elsevier, vol. 36(11), pages 6326-6339.
    16. Sadineni, Suresh B. & Madala, Srikanth & Boehm, Robert F., 2011. "Passive building energy savings: A review of building envelope components," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(8), pages 3617-3631.
    17. Budzianowski, Wojciech M., 2016. "A review of potential innovations for production, conditioning and utilization of biogas with multiple-criteria assessment," Renewable and Sustainable Energy Reviews, Elsevier, vol. 54(C), pages 1148-1171.
    18. Aghbashlo, Mortaza & Tabatabaei, Meisam & Rastegari, Hajar & Ghaziaskar, Hassan S. & Valijanian, Elena, 2018. "Exergy-based optimization of a continuous reactor applied to produce value-added chemicals from glycerol through esterification with acetic acid," Energy, Elsevier, vol. 150(C), pages 351-362.
    19. Gil, María V. & Riaza, Juan & Álvarez, Lucía & Pevida, Covadonga & Rubiera, Fernando, 2015. "Biomass devolatilization at high temperature under N2 and CO2: Char morphology and reactivity," Energy, Elsevier, vol. 91(C), pages 655-662.
    20. Rashwan, Sherif S. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Nemitallah, Medhat A. & Habib, Mohamed A., 2017. "Experimental study of atmospheric partially premixed oxy-combustion flames anchored over a perforated plate burner," Energy, Elsevier, vol. 122(C), pages 159-167.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:51:y:2013:i:c:p:267-272. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.