IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v198y2017icp99-107.html
   My bibliography  Save this article

Flame downwash length evolution of non-premixed gaseous fuel jets in cross-flow: Experiments and a new correlation

Author

Listed:
  • Shang, Fengju
  • Hu, Longhua
  • Sun, Xiepeng
  • Wang, Qiang
  • Palacios, Adriana

Abstract

Flame downwash behavior (flame pulled by the wake flow and attached to the leeward side of the nozzle) of gaseous fuel jets in cross-flow is of much practical importance in the design of burners as well as industrial flare, and thus important for energy conversion and conservation; however, the studies are still very limited. The critical condition (i.e., critical cross-flow air speed) for flame downwash occurrence as well as the evolution of flame downwash length for various fuel jet exit velocities has not been quantified yet. In this work, the flame downwash length evolution of non-premixed jets for different pipe nozzle diameters at various fuel discharge velocities and cross-flow air speeds as well as the critical condition under which the flame downwash occurs have been quantified comprehensively. Pipe nozzles with inner diameters of 8, 10, 13 and 15mm were employed in the experiments, using propane as the fuel and with fuel jet velocities ranging between 0.38 and 2.42m/s. The experimental results showed that the flame downwash length increased with increasing cross-flow air speed for a given fuel jet exit velocity. It was also found that, with increasing cross-flow air speed, the downwash length increased more rapidly for the higher fuel jet exit velocity than that for the lower fuel jet velocity. The critical cross-flow air speed, when flame downwash occurs, was found to be little dependent on the nozzle diameter but increase with the fuel jet exit velocity following a linear relationship. A new correlation for flame downwash length was proposed based on physically the coupling effects due to the competition of the fuel jet momentum to the cross-flow momentum and the total fuel mass supply. The proposed correlation was shown to well characterize the flame downwash length in terms of nozzle inner diameters, dimensionless fuel mass flow rates and the jet momentum ratio. The findings of this work provide basic knowledge and have potential practical applications for burner design and flare implementation, which allow predictions to be made regarding the possible threat and the establishment of the necessary safety length for the stack to prevent the damage for reducing the potential risk.

Suggested Citation

  • Shang, Fengju & Hu, Longhua & Sun, Xiepeng & Wang, Qiang & Palacios, Adriana, 2017. "Flame downwash length evolution of non-premixed gaseous fuel jets in cross-flow: Experiments and a new correlation," Applied Energy, Elsevier, vol. 198(C), pages 99-107.
    • Handle: RePEc:eee:appene:v:198:y:2017:i:c:p:99-107
    DOI: 10.1016/j.apenergy.2017.04.043
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261917304439
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2017.04.043?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Choy, Y.S. & Zhen, H.S. & Leung, C.W. & Li, H.B., 2012. "Pollutant emission and noise radiation from open and impinging inverse diffusion flames," Applied Energy, Elsevier, vol. 91(1), pages 82-89.
    2. Porzio, Giacomo Filippo & Nastasi, Gianluca & Colla, Valentina & Vannucci, Marco & Branca, Teresa Annunziata, 2014. "Comparison of multi-objective optimization techniques applied to off-gas management within an integrated steelwork," Applied Energy, Elsevier, vol. 136(C), pages 1085-1097.
    3. Huang, X.Q. & Leung, C.W. & Chan, C.K. & Probert, S.D., 2006. "Thermal characteristics of a premixed impinging circular laminar-flame jet with induced swirl," Applied Energy, Elsevier, vol. 83(4), pages 401-411, April.
    4. Lawal, Mohammed S. & Fairweather, Michael & Gogolek, Peter & Ingham, Derek B. & Ma, Lin & Pourkashanian, Mohamed & Williams, Alan, 2013. "CFD predictions of wake-stabilised jet flames in a cross-flow," Energy, Elsevier, vol. 53(C), pages 259-269.
    5. Lee, Woo Jin & Shin, Hyun Dong, 2003. "Visual characteristics, including lift-off, of the jet flames in a cross-flow high-temperature burner," Applied Energy, Elsevier, vol. 76(1-3), pages 257-266, September.
    6. Akbari, M.H. & Riahi, P. & Roohi, R., 2009. "Lean flammability limits for stable performance with a porous burner," Applied Energy, Elsevier, vol. 86(12), pages 2635-2643, December.
    7. Rashwan, Sherif S. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Nemitallah, Medhat A. & Habib, Mohamed A., 2016. "Experimental investigation of partially premixed methane–air and methane–oxygen flames stabilized over a perforated-plate burner," Applied Energy, Elsevier, vol. 169(C), pages 126-137.
    8. Zhen, H.S. & Choy, Y.S. & Leung, C.W. & Cheung, C.S., 2011. "Effects of nozzle length on flame and emission behaviors of multi-fuel-jet inverse diffusion flame burner," Applied Energy, Elsevier, vol. 88(9), pages 2917-2924.
    9. Terracciano, Anthony Carmine & Vasu, Subith S. & Orlovskaya, Nina, 2016. "Design and development of a porous heterogeneous combustor for efficient heat production by combustion of liquid and gaseous fuels," Applied Energy, Elsevier, vol. 179(C), pages 228-236.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Zhang, Xiaolei & Hu, Longhua & Delichatsios, Michael A. & Zhang, Jianping, 2019. "Experimental study on flame morphologic characteristics of wall attached non-premixed buoyancy driven turbulent flames," Applied Energy, Elsevier, vol. 254(C).
    2. Wang, Qiang & Tang, Fei & Zhou, Zheng & Liu, Huan & Palacios, Adriana, 2017. "Flame height of axisymmetric gaseous fuel jets restricted by parallel sidewalls: Experiments and theoretical analysis," Applied Energy, Elsevier, vol. 208(C), pages 1519-1526.
    3. Li, Xin & Hu, Longhua & Shang, Fengju, 2018. "Flame downwash transition and its maximum length with increasing fuel supply of non-premixed jet in cross flow," Energy, Elsevier, vol. 164(C), pages 298-305.
    4. Sun, Xiepeng & Zhang, Xiaolei & Lv, Jiang & Chen, Xiaotao & Hu, Longhua, 2023. "Experimental study on the buoyant turbulent diffusion flame height of various intermittent levels," Applied Energy, Elsevier, vol. 351(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Wang, Qiang & Tang, Fei & Zhou, Zheng & Liu, Huan & Palacios, Adriana, 2017. "Flame height of axisymmetric gaseous fuel jets restricted by parallel sidewalls: Experiments and theoretical analysis," Applied Energy, Elsevier, vol. 208(C), pages 1519-1526.
    2. Wan, Huaxian & Gao, Zihe & Ji, Jie & Li, Kaiyuan & Sun, Jinhua & Zhang, Yongming, 2017. "Experimental study on ceiling gas temperature and flame performances of two buoyancy-controlled propane burners located in a tunnel," Applied Energy, Elsevier, vol. 185(P1), pages 573-581.
    3. Zhang, Xiaolei & Hu, Longhua & Delichatsios, Michael A. & Zhang, Jianping, 2019. "Experimental study on flame morphologic characteristics of wall attached non-premixed buoyancy driven turbulent flames," Applied Energy, Elsevier, vol. 254(C).
    4. Gao, Zihe & Wan, Huaxian & Ji, Jie & Bi, Yubo, 2019. "Experimental prediction on the performance and propagation of ceiling jets under the influence of wall confinement," Energy, Elsevier, vol. 178(C), pages 378-385.
    5. Miao, J. & Leung, C.W. & Cheung, C.S. & Huang, Z.H. & Zhen, H.S., 2016. "Effect of hydrogen addition on overall pollutant emissions of inverse diffusion flame," Energy, Elsevier, vol. 104(C), pages 284-294.
    6. Li, Xin & Hu, Longhua & Shang, Fengju, 2018. "Flame downwash transition and its maximum length with increasing fuel supply of non-premixed jet in cross flow," Energy, Elsevier, vol. 164(C), pages 298-305.
    7. Tang, Fei & Hu, Peng & Shi, Congling, 2021. "Ceiling thermal impingement spread characteristics induced by wall-attached fires under various sub-atmospheric pressures," Energy, Elsevier, vol. 215(PB).
    8. Matino, Ismael & Dettori, Stefano & Colla, Valentina & Weber, Valentine & Salame, Sahar, 2019. "Forecasting blast furnace gas production and demand through echo state neural network-based models: Pave the way to off-gas optimized management," Applied Energy, Elsevier, vol. 253(C), pages 1-1.
    9. Porzio, Giacomo Filippo & Colla, Valentina & Fornai, Barbara & Vannucci, Marco & Larsson, Mikael & Stripple, Håkan, 2016. "Process integration analysis and some economic-environmental implications for an innovative environmentally friendly recovery and pre-treatment of steel scrap," Applied Energy, Elsevier, vol. 161(C), pages 656-672.
    10. Rashwan, Sherif S. & Shaaban, Ahmed M. & Al-Suliman, Fahad, 2017. "A comparative study of a small-scale solar PV power plant in Saudi Arabia," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 313-318.
    11. Zaidani, Mouna & Tajik, Abdul Raouf & Qureshi, Zahid Ahmed & Shamim, Tariq & Abu Al-Rub, Rashid K., 2018. "Investigating the flue-wall deformation effects on performance characteristics of an open-top aluminum anode baking furnace," Applied Energy, Elsevier, vol. 231(C), pages 1033-1049.
    12. Chen, Qianqian & Gu, Yu & Tang, Zhiyong & Wei, Wei & Sun, Yuhan, 2018. "Assessment of low-carbon iron and steel production with CO2 recycling and utilization technologies: A case study in China," Applied Energy, Elsevier, vol. 220(C), pages 192-207.
    13. Billerot, Pierre-Lou & Dufresne, Louis & Lemaire, Romain & Seers, Patrice, 2020. "3D CFD analysis of a diamond lattice-based porous burner," Energy, Elsevier, vol. 207(C).
    14. Akbari, M.H. & Riahi, P., 2010. "Investigation of the structural and reactants properties on the thermal characteristics of a premixed porous burner," Applied Energy, Elsevier, vol. 87(4), pages 1433-1440, April.
    15. Kapusta, Łukasz Jan & Shuang, Chen & Aldén, Marcus & Li, Zhongshan, 2020. "Structures of inverse jet flames stabilized on a coaxial burner," Energy, Elsevier, vol. 193(C).
    16. Su, Kun & Ouyang, Ziqu & Wang, Hongshuai & Ding, Hongliang & Zhang, Jinyang & Wang, Wenyu, 2024. "Effects of activated fuel and staged secondary air distributions on purification, combustion and NOx emission characteristics of pulverized coal with purification-combustion technology," Energy, Elsevier, vol. 302(C).
    17. Zhen, H.S. & Leung, C.W. & Cheung, C.S., 2011. "Emission of impinging swirling and non-swirling inverse diffusion flames," Applied Energy, Elsevier, vol. 88(5), pages 1629-1634, May.
    18. Rashwan, Sherif S. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Nemitallah, Medhat A. & Habib, Mohamed A., 2017. "Experimental study of atmospheric partially premixed oxy-combustion flames anchored over a perforated plate burner," Energy, Elsevier, vol. 122(C), pages 159-167.
    19. Ramadan, Islam A. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Rashwan, Sherif S. & Nemitallah, Medhat A. & Habib, Mohamed A., 2016. "Effects of oxidizer flexibility and bluff-body blockage ratio on flammability limits of diffusion flames," Applied Energy, Elsevier, vol. 178(C), pages 19-28.
    20. Juxian Hao & Xiancong Zhao & Hao Bai, 2017. "Collaborative Scheduling between OSPPs and Gasholders in Steel Mill under Time-of-Use Power Price," Energies, MDPI, vol. 10(8), pages 1-10, August.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:198:y:2017:i:c:p:99-107. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.