IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v179y2016icp806-820.html
   My bibliography  Save this article

Thermodynamic and economic analysis of a supercritical and an ultracritical oxy-type power plant without and with waste heat recovery

Author

Listed:
  • Kotowicz, Janusz
  • Michalski, Sebastian

Abstract

Thermodynamic and economic analysis of two variants (W1 and W2) of an oxy-type power plant (with or without waste heat recovery) are presented in this paper. This plant consists of: a hard-coal-fired pulverized-fuel boiler, a steam turbine unit, a CO2 capture and compression unit and an air separation unit (with a four-end-type high-temperature membrane). A steam turboset gross electric power of 600MW was assumed. Variants of the oxy-type plant have different live steam parameters (W1–650°C/30MPa; W2-700°C/35MPa), reheated steam parameters (W1–670°C/6MPa; W2-720°C/6.5MPa) and structures of the steam turbine unit. Two methods of utilization of waste heat were analyzed: replacement of regenerative feed water heaters and implementation of an additional ORC unit. The characteristics of the thermodynamic and economic analysis of the analyzed plant were determined as a function of the air compressor pressure ratio (β) and oxygen recovery rate (R). The values of these quantities were determined to ensure maximal net efficiency of the plant and the best value of the economic indicator. The results show that utilization of waste heat is essential for efficiency and economic indicator values of the oxy-type plant and optimal values of β and R. The net efficiency of the oxy-type plant can be 4.06p.p. lower than the analogous efficiency of the reference plant (consisting of a classic pulverized-fuel boiler and steam turbine unit). This decrease of the efficiency is one of the lowest among the CO2 capture technologies.

Suggested Citation

  • Kotowicz, Janusz & Michalski, Sebastian, 2016. "Thermodynamic and economic analysis of a supercritical and an ultracritical oxy-type power plant without and with waste heat recovery," Applied Energy, Elsevier, vol. 179(C), pages 806-820.
    • Handle: RePEc:eee:appene:v:179:y:2016:i:c:p:806-820
    DOI: 10.1016/j.apenergy.2016.07.013
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261916309540
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2016.07.013?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Kotowicz, Janusz & Michalski, Sebastian, 2014. "Efficiency analysis of a hard-coal-fired supercritical power plant with a four-end high-temperature membrane for air separation," Energy, Elsevier, vol. 64(C), pages 109-119.
    2. Liszka, M. & Ziębik, A., 2010. "Coal-fired oxy-fuel power unit – Process and system analysis," Energy, Elsevier, vol. 35(2), pages 943-951.
    3. Fu, Chao & Anantharaman, Rahul & Gundersen, Truls, 2015. "Optimal integration of compression heat with regenerative steam Rankine cycles in oxy-combustion coal based power plants," Energy, Elsevier, vol. 84(C), pages 612-622.
    4. Skorek-Osikowska, Anna & Janusz-Szymańska, Katarzyna & Kotowicz, Janusz, 2012. "Modeling and analysis of selected carbon dioxide capture methods in IGCC systems," Energy, Elsevier, vol. 45(1), pages 92-100.
    5. Xu, Gang & Xu, Cheng & Yang, Yongping & Fang, Yaxiong & Zhou, Luyao & Zhang, Kai, 2014. "Novel partial-subsidence tower-type boiler design in an ultra-supercritical power plant," Applied Energy, Elsevier, vol. 134(C), pages 363-373.
    6. Fu, Qian & Kansha, Yasuki & Song, Chunfeng & Liu, Yuping & Ishizuka, Masanori & Tsutsumi, Atsushi, 2016. "A cryogenic air separation process based on self-heat recuperation for oxy-combustion plants," Applied Energy, Elsevier, vol. 162(C), pages 1114-1121.
    7. Castillo, Renzo, 2011. "Thermodynamic analysis of a hard coal oxyfuel power plant with high temperature three-end membrane for air separation," Applied Energy, Elsevier, vol. 88(5), pages 1480-1493, May.
    8. Kotowicz, Janusz & Sobolewski, Aleksander & Iluk, Tomasz, 2013. "Energetic analysis of a system integrated with biomass gasification," Energy, Elsevier, vol. 52(C), pages 265-278.
    9. Kotowicz, Janusz & Michalski, Sebastian, 2015. "Influence of four-end HTM (high temperature membrane) parameters on the thermodynamic and economic characteristics of a supercritical power plant," Energy, Elsevier, vol. 81(C), pages 662-673.
    10. Bartela, Łukasz & Skorek-Osikowska, Anna & Kotowicz, Janusz, 2014. "Economic analysis of a supercritical coal-fired CHP plant integrated with an absorption carbon capture installation," Energy, Elsevier, vol. 64(C), pages 513-523.
    11. Corti, Andrea & Fiaschi, Daniele & Lombardi, Lidia, 2004. "Carbon dioxide removal in power generation using membrane technology," Energy, Elsevier, vol. 29(12), pages 2025-2043.
    12. Zhang, Wenbin & Liu, Hao & Sun, Yuan & Cakstins, Janis & Sun, Chenggong & Snape, Colin E., 2016. "Parametric study on the regeneration heat requirement of an amine-based solid adsorbent process for post-combustion carbon capture," Applied Energy, Elsevier, vol. 168(C), pages 394-405.
    13. Skorek-Osikowska, Anna & Bartela, Łukasz & Kotowicz, Janusz & Sobolewski, Aleksander & Iluk, Tomasz & Remiorz, Leszek, 2014. "The influence of the size of the CHP (combined heat and power) system integrated with a biomass fueled gas generator and piston engine on the thermodynamic and economic effectiveness of electricity an," Energy, Elsevier, vol. 67(C), pages 328-340.
    14. Yin, Chungen & Yan, Jinyue, 2016. "Oxy-fuel combustion of pulverized fuels: Combustion fundamentals and modeling," Applied Energy, Elsevier, vol. 162(C), pages 742-762.
    15. Gunasekaran, S. & Mancini, N.D. & Mitsos, A., 2014. "Optimal design and operation of membrane-based oxy-combustion power plants," Energy, Elsevier, vol. 70(C), pages 338-354.
    16. Franz, Johannes & Maas, Pascal & Scherer, Viktor, 2014. "Economic evaluation of pre-combustion CO2-capture in IGCC power plants by porous ceramic membranes," Applied Energy, Elsevier, vol. 130(C), pages 532-542.
    17. Garcia-Barberena, Javier & Monreal, Ana & Sánchez, Marcelino, 2014. "The BEPE – Break-Even Price of Energy: A financial figure of merit for renewable energy projects," Renewable Energy, Elsevier, vol. 71(C), pages 584-588.
    18. Gopan, Akshay & Kumfer, Benjamin M. & Phillips, Jeffrey & Thimsen, David & Smith, Richard & Axelbaum, Richard L., 2014. "Process design and performance analysis of a Staged, Pressurized Oxy-Combustion (SPOC) power plant for carbon capture," Applied Energy, Elsevier, vol. 125(C), pages 179-188.
    19. Kotowicz, Janusz & Chmielniak, Tadeusz & Janusz-Szymańska, Katarzyna, 2010. "The influence of membrane CO2 separation on the efficiency of a coal-fired power plant," Energy, Elsevier, vol. 35(2), pages 841-850.
    20. Bu, Changsheng & Gómez-Barea, Alberto & Chen, Xiaoping & Leckner, Bo & Liu, Daoyin & Pallarès, David & Lu, Ping, 2016. "Effect of CO2 on oxy-fuel combustion of coal-char particles in a fluidized bed: Modeling and comparison with the conventional mode of combustion," Applied Energy, Elsevier, vol. 177(C), pages 247-259.
    21. Giuffrida, Antonio & Romano, Matteo C. & Lozza, Giovanni, 2013. "Efficiency enhancement in IGCC power plants with air-blown gasification and hot gas clean-up," Energy, Elsevier, vol. 53(C), pages 221-229.
    22. Quoilin, Sylvain & Broek, Martijn Van Den & Declaye, Sébastien & Dewallef, Pierre & Lemort, Vincent, 2013. "Techno-economic survey of Organic Rankine Cycle (ORC) systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 22(C), pages 168-186.
    23. Davison, John, 2007. "Performance and costs of power plants with capture and storage of CO2," Energy, Elsevier, vol. 32(7), pages 1163-1176.
    24. Goto, Kazuya & Yogo, Katsunori & Higashii, Takayuki, 2013. "A review of efficiency penalty in a coal-fired power plant with post-combustion CO2 capture," Applied Energy, Elsevier, vol. 111(C), pages 710-720.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Habib, Mohamed A. & Imteyaz, Binash & Nemitallah, Medhat A., 2020. "Second law analysis of premixed and non-premixed oxy-fuel combustion cycles utilizing oxygen separation membranes," Applied Energy, Elsevier, vol. 259(C).
    2. Wang, Yanhong & Cao, Lihua & Hu, Pengfei & Li, Bo & Li, Yong, 2019. "Model establishment and performance evaluation of a modified regenerative system for a 660 MW supercritical unit running at the IPT-setting mode," Energy, Elsevier, vol. 179(C), pages 890-915.
    3. Hu, Yukun & Wang, Jihong & Tan, CK & Sun, Chenggong & Liu, Hao, 2018. "Coupling detailed radiation model with process simulation in Aspen Plus: A case study on fluidized bed combustor," Applied Energy, Elsevier, vol. 227(C), pages 168-179.
    4. Taler, Jan & Zima, Wiesław & Ocłoń, Paweł & Grądziel, Sławomir & Taler, Dawid & Cebula, Artur & Jaremkiewicz, Magdalena & Korzeń, Anna & Cisek, Piotr & Kaczmarski, Karol & Majewski, Karol, 2019. "Mathematical model of a supercritical power boiler for simulating rapid changes in boiler thermal loading," Energy, Elsevier, vol. 175(C), pages 580-592.
    5. Janusz Kotowicz & Sebastian Michalski & Mateusz Brzęczek, 2019. "The Characteristics of a Modern Oxy-Fuel Power Plant," Energies, MDPI, vol. 12(17), pages 1-34, September.
    6. Li, Yong & Wang, Yanhong & Cao, Lihua & Hu, Pengfei & Han, Wei, 2018. "Modeling for the performance evaluation of 600 MW supercritical unit operating No.0 high pressure heater," Energy, Elsevier, vol. 149(C), pages 639-661.
    7. Wang, Yu & Ren, Changyifan & Guo, Shenghui & Liu, Shi & Du, Mingming & Chen, Yunan & Guo, Liejin, 2023. "Thermodynamic and environmental analysis of heat supply in pig manure supercritical water gasification system," Energy, Elsevier, vol. 263(PA).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Janusz Kotowicz & Sebastian Michalski & Mateusz Brzęczek, 2019. "The Characteristics of a Modern Oxy-Fuel Power Plant," Energies, MDPI, vol. 12(17), pages 1-34, September.
    2. Kotowicz, Janusz & Michalski, Sebastian, 2015. "Influence of four-end HTM (high temperature membrane) parameters on the thermodynamic and economic characteristics of a supercritical power plant," Energy, Elsevier, vol. 81(C), pages 662-673.
    3. Janusz-Szymańska, Katarzyna & Dryjańska, Aleksandra, 2015. "Possibilities for improving the thermodynamic and economic characteristics of an oxy-type power plant with a cryogenic air separation unit," Energy, Elsevier, vol. 85(C), pages 45-61.
    4. Kotowicz, Janusz & Michalski, Sebastian, 2014. "Efficiency analysis of a hard-coal-fired supercritical power plant with a four-end high-temperature membrane for air separation," Energy, Elsevier, vol. 64(C), pages 109-119.
    5. Pettinau, Alberto & Ferrara, Francesca & Tola, Vittorio & Cau, Giorgio, 2017. "Techno-economic comparison between different technologies for CO2-free power generation from coal," Applied Energy, Elsevier, vol. 193(C), pages 426-439.
    6. Puig-Arnavat, Maria & Søgaard, Martin & Hjuler, Klaus & Ahrenfeldt, Jesper & Henriksen, Ulrik Birk & Hendriksen, Peter Vang, 2015. "Integration of oxygen membranes for oxygen production in cement plants," Energy, Elsevier, vol. 91(C), pages 852-865.
    7. Skorek-Osikowska, Anna & Bartela, Łukasz & Kotowicz, Janusz & Sobolewski, Aleksander & Iluk, Tomasz & Remiorz, Leszek, 2014. "The influence of the size of the CHP (combined heat and power) system integrated with a biomass fueled gas generator and piston engine on the thermodynamic and economic effectiveness of electricity an," Energy, Elsevier, vol. 67(C), pages 328-340.
    8. Bartela, Łukasz & Skorek-Osikowska, Anna & Kotowicz, Janusz, 2015. "An analysis of the investment risk related to the integration of a supercritical coal-fired combined heat and power plant with an absorption installation for CO2 separation," Applied Energy, Elsevier, vol. 156(C), pages 423-435.
    9. Xiang, Yanlei & Cai, Lei & Guan, Yanwen & Liu, Wenbin & Han, Yixiao & Liang, Ying, 2018. "Study on the configuration of bottom cycle in natural gas combined cycle power plants integrated with oxy-fuel combustion," Applied Energy, Elsevier, vol. 212(C), pages 465-477.
    10. Cabral, Renato P. & Mac Dowell, Niall, 2017. "A novel methodological approach for achieving £/MWh cost reduction of CO2 capture and storage (CCS) processes," Applied Energy, Elsevier, vol. 205(C), pages 529-539.
    11. Chen, Shiyi & Yu, Ran & Soomro, Ahsanullah & Xiang, Wenguo, 2019. "Thermodynamic assessment and optimization of a pressurized fluidized bed oxy-fuel combustion power plant with CO2 capture," Energy, Elsevier, vol. 175(C), pages 445-455.
    12. Zima, Wiesław & Nowak-Ocłoń, Marzena & Ocłoń, Paweł, 2015. "Simulation of fluid heating in combustion chamber waterwalls of boilers for supercritical steam parameters," Energy, Elsevier, vol. 92(P1), pages 117-127.
    13. José Luis Míguez & Jacobo Porteiro & Raquel Pérez-Orozco & Miguel Ángel Gómez, 2018. "Technology Evolution in Membrane-Based CCS," Energies, MDPI, vol. 11(11), pages 1-18, November.
    14. Mansir, Ibrahim B. & Ben-Mansour, Rached & Habib, Mohamed A., 2018. "Oxy-fuel combustion in a two-pass oxygen transport reactor for fire tube boiler application," Applied Energy, Elsevier, vol. 229(C), pages 828-840.
    15. Li, Jichao & Han, Wei & Li, Peijing & Ma, Wenjing & Xue, Xiaodong & Jin, Hongguang, 2023. "High-efficiency power generation system with CO2 capture based on cascading coal gasification employing chemical recuperation," Energy, Elsevier, vol. 283(C).
    16. Lupiáñez, Carlos & Carmen Mayoral, M. & Díez, Luis I. & Pueyo, Eloy & Espatolero, Sergio & Manuel Andrés, J., 2016. "The role of limestone during fluidized bed oxy-combustion of coal and biomass," Applied Energy, Elsevier, vol. 184(C), pages 670-680.
    17. Ramadan, Islam A. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Rashwan, Sherif S. & Nemitallah, Medhat A. & Habib, Mohamed A., 2016. "Effects of oxidizer flexibility and bluff-body blockage ratio on flammability limits of diffusion flames," Applied Energy, Elsevier, vol. 178(C), pages 19-28.
    18. Braimakis, Konstantinos & Magiri-Skouloudi, Despina & Grimekis, Dimitrios & Karellas, Sotirios, 2020. "Εnergy-exergy analysis of ultra-supercritical biomass-fuelled steam power plants for industrial CHP, district heating and cooling," Renewable Energy, Elsevier, vol. 154(C), pages 252-269.
    19. Alexander García-Mariaca & Eva Llera-Sastresa, 2021. "Review on Carbon Capture in ICE Driven Transport," Energies, MDPI, vol. 14(21), pages 1-30, October.
    20. Habib, Mohamed A. & Nemitallah, Medhat A., 2015. "Design of an ion transport membrane reactor for application in fire tube boilers," Energy, Elsevier, vol. 81(C), pages 787-801.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:179:y:2016:i:c:p:806-820. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.