IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v14y2022i17p10885-d903159.html
   My bibliography  Save this article

Feasibility Analysis of Biomass Hydrochar Blended Coal Injection for Blast Furnace

Author

Listed:
  • Kai Wang

    (School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China
    Shougang Jingtang Iron and Steel Co., Ltd., Tangshan 063200, China)

  • Jianliang Zhang

    (School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)

  • Shengli Wu

    (School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China
    Shougang Jingtang Iron and Steel Co., Ltd., Tangshan 063200, China)

  • Jianlong Wu

    (Shougang Jingtang Iron and Steel Co., Ltd., Tangshan 063200, China)

  • Kun Xu

    (School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)

  • Jiawen Liu

    (School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)

  • Xiaojun Ning

    (School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)

  • Guangwei Wang

    (School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)

Abstract

It is critical for the iron and steel industry to achieve green transformation and development by effectively utilizing abundant biomass resources in blast furnace ironmaking. In this paper, four types of typical biomass were carbonized and upgraded using the hydrothermal carbonization (HTC) method, and the metallurgical performance of the prepared hydrochar for blast furnace injection was systematically tested. The results show that HTC treatment could remove volatile matter and dissolved mineral elements in biomass so that the hydrochar had the characteristics of high fixed carbon and low ash and alkali metal content. Moreover, the hydrochar had good grindability and excellent combustion performance, which meet the requirements of blast furnace injection. Finally, the metallurgical performance of blended coal and wood chip hydrochar was examined. It was observed that when the ratio of hydrochar was less than 15%, it would not affect the blast furnace injection, and the potential safety hazard caused by the explosive hydrochar could be resolved by mixing hydrochar with anthracite. The application of hydrochar in blast furnace injection could not only alleviate the current energy shortage situation, but also be of great significance to realize the “carbon peak” of the steel industry.

Suggested Citation

  • Kai Wang & Jianliang Zhang & Shengli Wu & Jianlong Wu & Kun Xu & Jiawen Liu & Xiaojun Ning & Guangwei Wang, 2022. "Feasibility Analysis of Biomass Hydrochar Blended Coal Injection for Blast Furnace," Sustainability, MDPI, vol. 14(17), pages 1-17, August.
  • Handle: RePEc:gam:jsusta:v:14:y:2022:i:17:p:10885-:d:903159
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/14/17/10885/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2071-1050/14/17/10885/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Suopajärvi, Hannu & Pongrácz, Eva & Fabritius, Timo, 2013. "The potential of using biomass-based reducing agents in the blast furnace: A review of thermochemical conversion technologies and assessments related to sustainability," Renewable and Sustainable Energy Reviews, Elsevier, vol. 25(C), pages 511-528.
    2. Oladejo, Jumoke & Adegbite, Stephen & Gao, Xiang & Liu, Hao & Wu, Tao, 2018. "Catalytic and non-catalytic synergistic effects and their individual contributions to improved combustion performance of coal/biomass blends," Applied Energy, Elsevier, vol. 211(C), pages 334-345.
    3. Wu, Dongling & Zhou, Ping & Zhou, Chenn Q., 2019. "Evaluation of pulverized coal utilization in a blast furnace by numerical simulation and grey relational analysis," Applied Energy, Elsevier, vol. 250(C), pages 1686-1695.
    4. Wang, Guangwei & Zhang, Jianliang & Lee, Jui-Yuan & Mao, Xiaoming & Ye, Lian & Xu, Wanren & Ning, Xiaojun & Zhang, Nan & Teng, Haipeng & Wang, Chuan, 2020. "Hydrothermal carbonization of maize straw for hydrochar production and its injection for blast furnace," Applied Energy, Elsevier, vol. 266(C).
    5. Wei, Rufei & Zhang, Lingling & Cang, Daqiang & Li, Jiaxin & Li, Xianwei & Xu, Chunbao Charles, 2017. "Current status and potential of biomass utilization in ferrous metallurgical industry," Renewable and Sustainable Energy Reviews, Elsevier, vol. 68(P1), pages 511-524.
    6. Xu, Zhi-Xiang & Liu, Peng & Xu, Gui-Sheng & Liu, Qing & He, Zhi-Xia & Wang, Qian, 2017. "Bio-fuel oil characteristic from catalytic cracking of hydrogenated palm oil," Energy, Elsevier, vol. 133(C), pages 666-675.
    7. Gao, Pin & Zhou, Yiyuan & Meng, Fang & Zhang, Yihui & Liu, Zhenhong & Zhang, Wenqi & Xue, Gang, 2016. "Preparation and characterization of hydrochar from waste eucalyptus bark by hydrothermal carbonization," Energy, Elsevier, vol. 97(C), pages 238-245.
    8. Chen, Wei-Hsin & Cheng, Wen-Yi & Lu, Ke-Miao & Huang, Ying-Pin, 2011. "An evaluation on improvement of pulverized biomass property for solid fuel through torrefaction," Applied Energy, Elsevier, vol. 88(11), pages 3636-3644.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Guangwei Wang & Renguo Li & Jiayun Dan & Xiang Yuan & Jiugang Shao & Jiawen Liu & Kun Xu & Tao Li & Xiaojun Ning & Chuan Wang, 2023. "Preparation of Biomass Hydrochar and Application Analysis of Blast Furnace Injection," Energies, MDPI, vol. 16(3), pages 1-16, January.
    2. Wang, Guangwei & Li, Desheng & Xiong, Lin & Dan, Jiayun & Xu, Kun & Yuan, Xiang & Kan, Guangze & Ning, Xiaojun & Wang, Chuan, 2023. "Application of catalysts in biomass hydrothermal carbonization for the preparation of high-quality blast furnace injection fuel," Energy, Elsevier, vol. 283(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Wang, Guangwei & Li, Desheng & Xiong, Lin & Dan, Jiayun & Xu, Kun & Yuan, Xiang & Kan, Guangze & Ning, Xiaojun & Wang, Chuan, 2023. "Application of catalysts in biomass hydrothermal carbonization for the preparation of high-quality blast furnace injection fuel," Energy, Elsevier, vol. 283(C).
    2. Suopajärvi, Hannu & Umeki, Kentaro & Mousa, Elsayed & Hedayati, Ali & Romar, Henrik & Kemppainen, Antti & Wang, Chuan & Phounglamcheik, Aekjuthon & Tuomikoski, Sari & Norberg, Nicklas & Andefors, Alf , 2018. "Use of biomass in integrated steelmaking – Status quo, future needs and comparison to other low-CO2 steel production technologies," Applied Energy, Elsevier, vol. 213(C), pages 384-407.
    3. Yu-Chiao Lu & Liviu Brabie & Andrey V. Karasev & Chuan Wang, 2022. "Applications of Hydrochar and Charcoal in the Iron and Steelmaking Industry—Part 2: Carburization of Liquid Iron by Addition of Iron–Carbon Briquettes," Sustainability, MDPI, vol. 14(9), pages 1-20, April.
    4. Tao Li & Guangwei Wang & Heng Zhou & Xiaojun Ning & Cuiliu Zhang, 2022. "Numerical Simulation Study on the Effects of Co-Injection of Pulverized Coal and Hydrochar into the Blast Furnace," Sustainability, MDPI, vol. 14(8), pages 1-13, April.
    5. Wang, Guangwei & Zhang, Jianliang & Lee, Jui-Yuan & Mao, Xiaoming & Ye, Lian & Xu, Wanren & Ning, Xiaojun & Zhang, Nan & Teng, Haipeng & Wang, Chuan, 2020. "Hydrothermal carbonization of maize straw for hydrochar production and its injection for blast furnace," Applied Energy, Elsevier, vol. 266(C).
    6. Wei, Rufei & Meng, Kangzheng & Long, Hongming & Xu, ChunbaoCharles, 2024. "Biomass metallurgy: A sustainable and green path to a carbon-neutral metallurgical industry," Renewable and Sustainable Energy Reviews, Elsevier, vol. 199(C).
    7. Eunhye Song & Seyong Park & Seongkuk Han & Eusil Lee & Ho Kim, 2022. "Characteristics of Hydrothermal Carbonization Hydrochar Derived from Cattle Manure," Energies, MDPI, vol. 15(23), pages 1-14, December.
    8. Samuel Carrasco & Ernesto Pino-Cortés & Andrés Barra-Marín & Alejandro Fierro-Gallegos & Marcelo León, 2022. "Use of Hydrochar Produced by Hydrothermal Carbonization of Lignocellulosic Biomass for Thermal Power Plants in Chile: A Techno-Economic and Environmental Study," Sustainability, MDPI, vol. 14(13), pages 1-17, June.
    9. Yek, Peter Nai Yuh & Cheng, Yoke Wang & Liew, Rock Keey & Wan Mahari, Wan Adibah & Ong, Hwai Chyuan & Chen, Wei-Hsin & Peng, Wanxi & Park, Young-Kwon & Sonne, Christian & Kong, Sieng Huat & Tabatabaei, 2021. "Progress in the torrefaction technology for upgrading oil palm wastes to energy-dense biochar: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 151(C).
    10. Sun, Minmin & Zhang, Jianliang & Li, Kejiang & Barati, Mansoor & Liu, Zhibin, 2022. "Co-gasification characteristics of coke blended with hydro-char and pyro-char from bamboo," Energy, Elsevier, vol. 241(C).
    11. Lu, Ke-Miao & Lee, Wen-Jhy & Chen, Wei-Hsin & Lin, Ta-Chang, 2013. "Thermogravimetric analysis and kinetics of co-pyrolysis of raw/torrefied wood and coal blends," Applied Energy, Elsevier, vol. 105(C), pages 57-65.
    12. Chai, Li & Saffron, Christopher M., 2016. "Comparing pelletization and torrefaction depots: Optimization of depot capacity and biomass moisture to determine the minimum production cost," Applied Energy, Elsevier, vol. 163(C), pages 387-395.
    13. Ye, Lian & Zhang, Jianliang & Wang, Guangwei & Wang, Chen & Mao, Xiaoming & Ning, Xiaojun & Zhang, Nan & Teng, Haipeng & Li, Jinhua & Wang, Chuan, 2023. "Feasibility analysis of plastic and biomass hydrochar for blast furnace injection," Energy, Elsevier, vol. 263(PD).
    14. Qi, Jianhui & Zhao, Jianli & Xu, Yang & Wang, Yongjia & Han, Kuihua, 2018. "Segmented heating carbonization of biomass: Yields, property and estimation of heating value of chars," Energy, Elsevier, vol. 144(C), pages 301-311.
    15. Jiao, Shouhui & Wang, Feng & Wang, Lili & Biney, Bernard Wiafe & Liu, He & Chen, Kun & Guo, Aijun & Sun, Lanyi & Wang, Zongxian, 2022. "Systematic identification and distribution analysis of olefins in FCC slurry oil," Energy, Elsevier, vol. 239(PA).
    16. Pablo J. Arauzo & María Atienza-Martínez & Javier Ábrego & Maciej P. Olszewski & Zebin Cao & Andrea Kruse, 2020. "Combustion Characteristics of Hydrochar and Pyrochar Derived from Digested Sewage Sludge," Energies, MDPI, vol. 13(16), pages 1-15, August.
    17. Zola, Fernanda Cavicchioli & Colmenero, João Carlos & Aragão, Franciely Velozo & Rodrigues, Thaisa & Junior, Aldo Braghini, 2020. "Multicriterial model for selecting a charcoal kiln," Energy, Elsevier, vol. 190(C).
    18. Tran, Khanh-Quang & Luo, Xun & Seisenbaeva, Gulaim & Jirjis, Raida, 2013. "Stump torrefaction for bioenergy application," Applied Energy, Elsevier, vol. 112(C), pages 539-546.
    19. Fan, Yuyang & Tippayawong, Nakorn & Wei, Guoqiang & Huang, Zhen & Zhao, Kun & Jiang, Liqun & Zheng, Anqing & Zhao, Zengli & Li, Haibin, 2020. "Minimizing tar formation whilst enhancing syngas production by integrating biomass torrefaction pretreatment with chemical looping gasification," Applied Energy, Elsevier, vol. 260(C).
    20. Rousset, P. & Fernandes, K. & Vale, A. & Macedo, L. & Benoist, A., 2013. "Change in particle size distribution of Torrefied biomass during cold fluidization," Energy, Elsevier, vol. 51(C), pages 71-77.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:14:y:2022:i:17:p:10885-:d:903159. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.