IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v17y2024i21p5445-d1511143.html
   My bibliography  Save this article

Study of the Technical and Operational Parameters of Injectors Using Biogas Fuel

Author

Listed:
  • Michał Bembenek

    (Faculty of Mechanical Engineering and Robotics, AGH University of Krakow, A. Mickiewicza 30, 30-059 Krakow, Poland)

  • Vasyl Melnyk

    (Institute of Mechanical Engineering, Ivano-Frankivsk National Technical University of Oil and Gas, 76019 Ivano-Frankivsk, Ukraine)

  • Bolesław Karwat

    (Faculty of Mechanical Engineering and Robotics, AGH University of Krakow, A. Mickiewicza 30, 30-059 Krakow, Poland)

  • Tomasz Rokita

    (Faculty of Mechanical Engineering and Robotics, AGH University of Krakow, A. Mickiewicza 30, 30-059 Krakow, Poland)

  • Mariia Hnyp

    (Institute of Mechanical Engineering, Ivano-Frankivsk National Technical University of Oil and Gas, 76019 Ivano-Frankivsk, Ukraine)

  • Yurii Mosora

    (Institute of Mechanical Engineering, Ivano-Frankivsk National Technical University of Oil and Gas, 76019 Ivano-Frankivsk, Ukraine)

  • Łukasz Warguła

    (Institute of Machine Design, Faculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3, 60-965 Poznan, Poland)

Abstract

Using biogas fuel in a modern internal combustion engine equipped with gas equipment of the fourth and fifth generations can create several difficulties. This is due to the low heat of combustion of untreated biogas, the presence of moisture, and the specifics of the injectors. The main problem of the studies we considered is that there are no data on the operating parameters of biogas fuel injectors. Studies on the parameters of the Matrix, Barracuda, Valtek, Hana, and Keihin injectors in relation to biogas fuel were carried out according to performance indicators, the linearity of operation, the resistance of the injectors, the ability to maintain factory parameters, and service life. According to the indicators of performance and linearity of work, Valtek injectors have the highest deviation in productivity and linearity of work, with an average of 38.8%, and the lowest deviation of Barracuda injectors is 7.5%. Keihin (15.3%) and Hana injectors (19.1%) also showed good performance indicators, and therefore can be used effectively for biogas fuel systems. As a result of research on the response time of the injectors, it was established that the best indicators were found for Hana (1.75 ms) and Keihin (1.99 ms) injectors. Valtek injectors showed good response rates (2.07 ms), as did Barracuda injectors (2.19 ms), but the highest response time was found in Matrix injectors, with 2.44 ms. Keihin injectors had the lowest average resistance value of 1.25 ohms, and Valtek injectors had the highest resistance value of 3 ohms. According to the research results, Keihin, Matrix, and Barracuda injectors provide the best ability to maintain factory performance when using biogas fuel at 2 to 5%, and Valtek had the worst performance up to 20%. Keihin, Barracuda, and Hana experimental injectors had the highest service life, which is from 200 to 250 thousand km of car mileage. The lowest indicators were found for Valtek and Matrix injectors, the service life of which varies from 70 to 100 thousand km of mileage.

Suggested Citation

  • Michał Bembenek & Vasyl Melnyk & Bolesław Karwat & Tomasz Rokita & Mariia Hnyp & Yurii Mosora & Łukasz Warguła, 2024. "Study of the Technical and Operational Parameters of Injectors Using Biogas Fuel," Energies, MDPI, vol. 17(21), pages 1-13, October.
    • Handle: RePEc:gam:jeners:v:17:y:2024:i:21:p:5445-:d:1511143
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/17/21/5445/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/17/21/5445/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Feiz, Roozbeh & Ammenberg, Jonas, 2017. "Assessment of feedstocks for biogas production, part I—A multi-criteria approach," Resources, Conservation & Recycling, Elsevier, vol. 122(C), pages 373-387.
    2. Barik, Debabrata & Murugan, S. & Sivaram, N.M. & Baburaj, E. & Shanmuga Sundaram, P., 2017. "Experimental investigation on the behavior of a direct injection diesel engine fueled with Karanja methyl ester-biogas dual fuel at different injection timings," Energy, Elsevier, vol. 118(C), pages 127-138.
    3. Ganesh, Duraisamy & Ayyappan, P.R. & Murugan, Rangasamy, 2019. "Experimental investigation of iso-butanol/diesel reactivity controlled compression ignition combustion in a non-road diesel engine," Applied Energy, Elsevier, vol. 242(C), pages 1307-1319.
    4. Ma, Shuaiying & Zheng, Zunqing & Liu, Haifeng & Zhang, Quanchang & Yao, Mingfa, 2013. "Experimental investigation of the effects of diesel injection strategy on gasoline/diesel dual-fuel combustion," Applied Energy, Elsevier, vol. 109(C), pages 202-212.
    5. Qi, D.H. & Chen, H. & Geng, L.M. & Bian, Y.Z., 2011. "Effect of diethyl ether and ethanol additives on the combustion and emission characteristics of biodiesel-diesel blended fuel engine," Renewable Energy, Elsevier, vol. 36(4), pages 1252-1258.
    6. Li, Weiqi & Dai, Yaping & Ma, Linwei & Hao, Han & Lu, Haiyan & Albinson, Rosemary & Li, Zheng, 2015. "Oil-saving pathways until 2030 for road freight transportation in China based on a cost-optimization model," Energy, Elsevier, vol. 86(C), pages 369-384.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Khayum, Naseem & Anbarasu, S. & Murugan, S., 2021. "Optimization of fuel injection parameters and compression ratio of a biogas fueled diesel engine using methyl esters of waste cooking oil as a pilot fuel," Energy, Elsevier, vol. 221(C).
    2. Liu, Xinlei & Wang, Hu & Wang, Xiaofeng & Zheng, Zunqing & Yao, Mingfa, 2017. "Experimental and modelling investigations of the diesel surrogate fuels in direct injection compression ignition combustion," Applied Energy, Elsevier, vol. 189(C), pages 187-200.
    3. Tse, H. & Leung, C.W. & Cheung, C.S., 2015. "Investigation on the combustion characteristics and particulate emissions from a diesel engine fueled with diesel-biodiesel-ethanol blends," Energy, Elsevier, vol. 83(C), pages 343-350.
    4. Obed M. Ali & Rizalman Mamat & Gholamhassan Najafi & Talal Yusaf & Seyed Mohammad Safieddin Ardebili, 2015. "Optimization of Biodiesel-Diesel Blended Fuel Properties and Engine Performance with Ether Additive Using Statistical Analysis and Response Surface Methods," Energies, MDPI, vol. 8(12), pages 1-15, December.
    5. Vallinayagam, R. & Vedharaj, S. & Yang, W.M. & Roberts, W.L. & Dibble, R.W., 2015. "Feasibility of using less viscous and lower cetane (LVLC) fuels in a diesel engine: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 51(C), pages 1166-1190.
    6. Adhirath Mandal & Dowan Cha & HaengMuk Cho, 2023. "Impact of Waste Fry Biofuel on Diesel Engine Performance and Emissions," Energies, MDPI, vol. 16(9), pages 1-23, April.
    7. Wang, Xinyan & Zhao, Hua & Xie, Hui, 2016. "Effect of dilution strategies and direct injection ratios on stratified flame ignition (SFI) hybrid combustion in a PFI/DI gasoline engine," Applied Energy, Elsevier, vol. 165(C), pages 801-814.
    8. Song, Hongqing & Ou, Xunmin & Yuan, Jiehui & Yu, Mingxu & Wang, Cheng, 2017. "Energy consumption and greenhouse gas emissions of diesel/LNG heavy-duty vehicle fleets in China based on a bottom-up model analysis," Energy, Elsevier, vol. 140(P1), pages 966-978.
    9. Fan, Baowei & Pan, Jianfeng & Yang, Wenming & Chen, Wei & Bani, Stephen, 2017. "The influence of injection strategy on mixture formation and combustion process in a direct injection natural gas rotary engine," Applied Energy, Elsevier, vol. 187(C), pages 663-674.
    10. Jiang, Jingjing & Ye, Bin & Liu, Junguo, 2019. "Peak of CO2 emissions in various sectors and provinces of China: Recent progress and avenues for further research," Renewable and Sustainable Energy Reviews, Elsevier, vol. 112(C), pages 813-833.
    11. Li, Zilong & Zhang, Yaoyuan & Huang, Guan & Zhao, Wenbin & He, Zhuoyao & Qian, Yong & Lu, Xingcai, 2020. "Control of intake boundary conditions for enabling clean combustion in variable engine conditions under intelligent charge compression ignition (ICCI) mode," Applied Energy, Elsevier, vol. 274(C).
    12. Zhang, Chuanguo & Tu, Xiaohua, 2016. "The effect of global oil price shocks on China's metal markets," Energy Policy, Elsevier, vol. 90(C), pages 131-139.
    13. Catalano, Giovanni & D'Adamo, Idiano & Gastaldi, Massimo & Nizami, Abdul-Sattar & Ribichini, Marco, 2024. "Incentive policies in biomethane production toward circular economy," Renewable and Sustainable Energy Reviews, Elsevier, vol. 202(C).
    14. Xinda Zhu & Manu Mannazhi & Natascia Palazzo & Per-Erik Bengtsson & Öivind Andersson, 2020. "High-Speed Imaging of Spray Formation and Combustion in an Optical Engine: Effects of Injector Aging and TPGME as a Fuel Additive," Energies, MDPI, vol. 13(12), pages 1-26, June.
    15. Liang, Zhirong & Yu, Zhenhong & Liu, Haoye & Chen, Longfei & Huang, Xinyan, 2022. "Combustion and emission characteristics of a compression ignition engine burning a wide range of conventional hydrocarbon and alternative fuels," Energy, Elsevier, vol. 250(C).
    16. Dong, Shijun & Wang, Zhaowen & Yang, Can & Ou, Biao & Lu, Hongguang & Xu, Haocheng & Cheng, Xiaobei, 2018. "Investigations on the effects of fuel stratification on auto-ignition and combustion process of an ethanol/diesel dual-fuel engine," Applied Energy, Elsevier, vol. 230(C), pages 19-30.
    17. Ding, Botao & Wang, Ying & Bai, Yuanqi & Xie, Manyao & Chen, Jinge, 2024. "Effects of PODE substitution rate and fuel injection timing on combustion, emission characteristic and energy balance in PODE-gasoline dual direct-injection engine," Energy, Elsevier, vol. 294(C).
    18. Zhong, Yingzi & Han, Weiqiang & Jin, Chao & Tian, Xiaocong & Liu, Haifeng, 2022. "Study on effects of the hydroxyl group position and carbon chain length on combustion and emission characteristics of Reactivity Controlled Compression Ignition (RCCI) engine fueled with low-carbon st," Energy, Elsevier, vol. 239(PC).
    19. Matthias Klumpp, 2016. "To Green or Not to Green: A Political, Economic and Social Analysis for the Past Failure of Green Logistics," Sustainability, MDPI, vol. 8(5), pages 1-22, May.
    20. Zareh, Parvaneh & Zare, Ali Asghar & Ghobadian, Barat, 2017. "Comparative assessment of performance and emission characteristics of castor, coconut and waste cooking based biodiesel as fuel in a diesel engine," Energy, Elsevier, vol. 139(C), pages 883-894.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:17:y:2024:i:21:p:5445-:d:1511143. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.