IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v11y2018i2p336-d129985.html
   My bibliography  Save this article

Analysis of Combustion Process in Industrial Gas Engine with Prechamber-Based Ignition System

Author

Listed:
  • Rafał Ślefarski

    (Poznan University of Technology, Piotrowo 3 Str., Chair of Thermal Engineering, 60-965 Poznan, Poland)

  • Michał Gołębiewski

    (Poznan University of Technology, Piotrowo 3 Str., Chair of Thermal Engineering, 60-965 Poznan, Poland)

  • Paweł Czyżewski

    (Poznan University of Technology, Piotrowo 3 Str., Chair of Thermal Engineering, 60-965 Poznan, Poland)

  • Przemysław Grzymisławski

    (Poznan University of Technology, Piotrowo 3 Str., Chair of Thermal Engineering, 60-965 Poznan, Poland)

  • Jacek Wawrzyniak

    (Polish Oil & Gas Company, Branch KRIO Odolanow, Krotoszynska 148, 63-430 Odolanow, Poland)

Abstract

Application of a pre-combustion chamber (PCC) ignition system is one of the methods to improve combustion stability and reduce toxic compounds emission, especially NO x . Using PCC allows the operation of the engine at lean combustion conditions or the utilization of low calorific gaseous fuels such as syngas or biogas. The paper presents the results of an experimental study of the combustion process in two stroke, large bore, stationary gas engine GMVH 12 equipped with two spark plugs (2-SP) and a PCC ignition system. The experimental research has been performed during the normal operation of the engine in an industrial compression station. It was observed that application of PCC provides less cycle-to-cycle combustion variation (more than 10%) and nitric oxide and carbon monoxide emissions decreased to 60% and 26% respectively. The total hydrocarbon (THC) emission rate is 25% higher for the engine equipped with PCC, which results in roughly two percent engine efficiency decrease. Another important criterion of engine retrofitting was the PCC location in the engine head. The experimental results show that improvement of engine operating parameters was recorded only for a configuration with one port offset by 45° from the axis of the main chamber. The study of the ignition delay angle and equivalence ratio in PCC did not demonstrate explicit influence on engine performance.

Suggested Citation

  • Rafał Ślefarski & Michał Gołębiewski & Paweł Czyżewski & Przemysław Grzymisławski & Jacek Wawrzyniak, 2018. "Analysis of Combustion Process in Industrial Gas Engine with Prechamber-Based Ignition System," Energies, MDPI, vol. 11(2), pages 1-15, February.
    • Handle: RePEc:gam:jeners:v:11:y:2018:i:2:p:336-:d:129985
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/11/2/336/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/11/2/336/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Yousefi, Amin & Birouk, Madjid, 2017. "Investigation of natural gas energy fraction and injection timing on the performance and emissions of a dual-fuel engine with pre-combustion chamber under low engine load," Applied Energy, Elsevier, vol. 189(C), pages 492-505.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Ao Zhou & Hui Jin & Wenhan Cao & Ming Pang & Yangyang Li & Chao Zhu, 2022. "Influence of Pilot Injection on Combustion Characteristic of Methanol–Diesel Dual-Fuel Engine," Energies, MDPI, vol. 15(10), pages 1-14, May.
    2. Jiaying Pan & Yu He & Tao Li & Haiqiao Wei & Lei Wang & Gequn Shu, 2021. "Effect of Temperature Conditions on Flame Evolutions of Turbulent Jet Ignition," Energies, MDPI, vol. 14(8), pages 1-17, April.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Shu, Jun & Fu, Jianqin & Liu, Jingping & Ma, Yinjie & Wang, Shuqian & Deng, Banglin & Zeng, Dongjian, 2019. "Effects of injector spray angle on combustion and emissions characteristics of a natural gas (NG)-diesel dual fuel engine based on CFD coupled with reduced chemical kinetic model," Applied Energy, Elsevier, vol. 233, pages 182-195.
    2. Hammam Aljabri & Mickael Silva & Moez Ben Houidi & Xinlei Liu & Moaz Allehaibi & Fahad Almatrafi & Abdullah S. AlRamadan & Balaji Mohan & Emre Cenker & Hong G. Im, 2022. "Comparative Study of Spark-Ignited and Pre-Chamber Hydrogen-Fueled Engine: A Computational Approach," Energies, MDPI, vol. 15(23), pages 1-21, November.
    3. Darzi, Mahdi & Johnson, Derek & Ulishney, Chris & Clark, Nigel, 2018. "Low pressure direct injection strategies effect on a small SI natural gas two-stroke engine’s energy distribution and emissions," Applied Energy, Elsevier, vol. 230(C), pages 1585-1602.
    4. Zhongchao Zhao & Kai Zhao & Dandan Jia & Pengpeng Jiang & Rendong Shen, 2017. "Numerical Investigation on the Flow and Heat Transfer Characteristics of Supercritical Liquefied Natural Gas in an Airfoil Fin Printed Circuit Heat Exchanger," Energies, MDPI, vol. 10(11), pages 1-18, November.
    5. Lounici, M.S. & Benbellil, M.A. & Loubar, K. & Niculescu, D.C. & Tazerout, M., 2017. "Knock characterization and development of a new knock indicator for dual-fuel engines," Energy, Elsevier, vol. 141(C), pages 2351-2361.
    6. Hoang, Anh Tuan & Murugesan, Parthasarathy & PV, Elumalai & Balasubramanian, Dhinesh & Parida, Satyajeet & Priya Jayabal, Chandra & Nachippan, Murugu & Kalam, M.A & Truong, Thanh Hai & Cao, Dao Nam & , 2023. "Strategic combination of waste plastic/tire pyrolysis oil with biodiesel for natural gas-enriched HCCI engine: Experimental analysis and machine learning model," Energy, Elsevier, vol. 280(C).
    7. Chen, Wei & Pan, Jianfeng & Liu, Yangxian & Fan, Baowei & Liu, Hongjun & Otchere, Peter, 2019. "Numerical investigation of direct injection stratified charge combustion in a natural gas-diesel rotary engine," Applied Energy, Elsevier, vol. 233, pages 453-467.
    8. Min Zhang & Wanhua Su & Zhi Jia, 2024. "Study of Efficient and Clean Combustion of Diesel–Natural Gas Engine at Low Loads with Concentration and Temperature Stratified Combustion," Energies, MDPI, vol. 17(17), pages 1-22, August.
    9. Qiu, Songgang & Gao, Yuan & Rinker, Garrett & Yanaga, Koji, 2019. "Development of an advanced free-piston Stirling engine for micro combined heating and power application," Applied Energy, Elsevier, vol. 235(C), pages 987-1000.
    10. Tavakoli, Sadi & Saettone, Simone & Steen, Sverre & Andersen, Poul & Schramm, Jesper & Pedersen, Eilif, 2020. "Modeling and analysis of performance and emissions of marine lean-burn natural gas engine propulsion in waves," Applied Energy, Elsevier, vol. 279(C).
    11. Yousefi, Amin & Guo, Hongsheng & Birouk, Madjid, 2018. "Effect of swirl ratio on NG/diesel dual-fuel combustion at low to high engine load conditions," Applied Energy, Elsevier, vol. 229(C), pages 375-388.
    12. Fan, Baowei & Zeng, Yonghao & Pan, Jianfeng & Fang, Jia & Salami, Hammed Adeniyi & Wang, Yuanguang, 2022. "Numerical study of injection strategy on the combustion process in a peripheral ported rotary engine fueled with natural gas/hydrogen blends under the action of apex seal leakage," Energy, Elsevier, vol. 242(C).
    13. Benbellil, Messaoud Abdelalli & Lounici, Mohand Said & Loubar, Khaled & Tazerout, Mohand, 2022. "Investigation of natural gas enrichment with high hydrogen participation in dual fuel diesel engine," Energy, Elsevier, vol. 243(C).
    14. Abhinandhan Narayanan & Deivanayagam Hariharan & Kendyl Ryan Partridge & Austin Leo Pearson & Kalyan Kumar Srinivasan & Sundar Rajan Krishnan, 2023. "Impact of Low Reactivity Fuel Type and Energy Substitution on Dual Fuel Combustion at Different Injection Timings," Energies, MDPI, vol. 16(4), pages 1-36, February.
    15. Di Blasio, G. & Belgiorno, G. & Beatrice, C., 2017. "Effects on performances, emissions and particle size distributions of a dual fuel (methane-diesel) light-duty engine varying the compression ratio," Applied Energy, Elsevier, vol. 204(C), pages 726-740.
    16. Zhang, R.C. & Hao, F. & Fan, W.J., 2018. "Combustion and stability characteristics of ultra-compact combustor using cavity for gas turbines," Applied Energy, Elsevier, vol. 225(C), pages 940-954.
    17. Ji, Shaobo & Li, Yang & Tian, Guohong & Shu, Minglei & Jia, Guorui & He, Shaoqing & Lan, Xin & Cheng, Yong, 2021. "Investigation of laminar combustion characteristics of ozonized methane-air mixture in a constant volume combustion bomb," Energy, Elsevier, vol. 226(C).
    18. Zhang, Wei & Chen, Zhaohui & Duan, Qiwang & Jiang, Qianyu, 2021. "Visual test and evolutionary analysis of flow fields in cylinder of helical intake port diesel engine," Energy, Elsevier, vol. 223(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:11:y:2018:i:2:p:336-:d:129985. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.