IDEAS home Printed from https://ideas.repec.org/a/eee/renene/v154y2020icp581-597.html
   My bibliography  Save this article

Assessment of the Stirling engine performance comparing two renewable energy sources: Solar energy and biomass

Author

Listed:
  • Ferreira, Ana Cristina
  • Silva, João
  • Teixeira, Senhorinha
  • Teixeira, José Carlos
  • Nebra, Silvia Azucena

Abstract

The paper addresses the assessment of the Stirling engine performance by comparing biomass and solar energy as external renewable energy sources. A program-code was developed in the MatLab® to solve the thermal model of an alpha-Stirling engine, accounting for the limitations in the heat transfer processes in the regenerator and the losses due to pumping effects. The solar energy source was modelled as a concentric solar dish collector, considering a receiver located at the focal point and designed to absorb the maximum possible of the solar radiation. Regarding the biomass system, the temperature of the flue gases leaving the bed is computed through an energy balance, considering the fuel energy introduced into the bed, the energy that is provided by the bed and the incident radiation in the bed. The simulation results show that the biomass-fuelled Stirling engine provided 87.5% more power output than the solar energy source, with an efficiency of 46.67%. Also, the average receiver temperature from the solar source is about 775 K, whereas, in the boiler bed, the temperature reaches the value of 1288 K. In the solar-dish modelling, the reflected radiation that passes into the cavity receiver depends on the aperture ratio and rim angle. It was proved that a rim angle of at least 45° is required to ensure lower focal distances. Otherwise, the Stirling receiver needs to be far from the surface of the dish, resulting in higher thermal losses and lower temperature inside the receiver cavity. In biomass-fuelled system, it was shown that the temperature of the flue gases increases with the increasing the radiation flux, and decreases for higher split percentages between the primary and secondary air. The study also revealed the need to investigate the combustion stability regarding the particle emission in the flue gas, which can reduce the temperature close to the hot cylinder of the Stirling engine. The LCoE for the solar-power system is of about 1658 €/kWh, which is 52% higher when compared with the biomass-fuelled system (0.109 €/kWh). In conclusion, biomass-fuelled Stirling engines are able to provide a higher power output with higher thermal efficiency, avoiding the problems usually related to solar energy intermittency.

Suggested Citation

  • Ferreira, Ana Cristina & Silva, João & Teixeira, Senhorinha & Teixeira, José Carlos & Nebra, Silvia Azucena, 2020. "Assessment of the Stirling engine performance comparing two renewable energy sources: Solar energy and biomass," Renewable Energy, Elsevier, vol. 154(C), pages 581-597.
    • Handle: RePEc:eee:renene:v:154:y:2020:i:c:p:581-597
    DOI: 10.1016/j.renene.2020.03.020
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0960148120303426
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.renene.2020.03.020?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Kongtragool, Bancha & Wongwises, Somchai, 2006. "Thermodynamic analysis of a Stirling engine including dead volumes of hot space, cold space and regenerator," Renewable Energy, Elsevier, vol. 31(3), pages 345-359.
    2. Connolly, D. & Lund, H. & Mathiesen, B.V., 2016. "Smart Energy Europe: The technical and economic impact of one potential 100% renewable energy scenario for the European Union," Renewable and Sustainable Energy Reviews, Elsevier, vol. 60(C), pages 1634-1653.
    3. Campos, M.C. & Vargas, J.V.C. & Ordonez, J.C., 2012. "Thermodynamic optimization of a Stirling engine," Energy, Elsevier, vol. 44(1), pages 902-910.
    4. Ahmadi, Mohammad H. & Ahmadi, Mohammad-Ali & Pourfayaz, Fathollah, 2017. "Thermal models for analysis of performance of Stirling engine: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 68(P1), pages 168-184.
    5. Timoumi, Youssef & Tlili, Iskander & Ben Nasrallah, Sassi, 2008. "Design and performance optimization of GPU-3 Stirling engines," Energy, Elsevier, vol. 33(7), pages 1100-1114.
    6. Alanne, Kari & Saari, Arto, 2004. "Sustainable small-scale CHP technologies for buildings: the basis for multi-perspective decision-making," Renewable and Sustainable Energy Reviews, Elsevier, vol. 8(5), pages 401-431, October.
    7. Huang, Junpeng & Fan, Jianhua & Furbo, Simon & Chen, Daochuan & Dai, Yanjun & Kong, Weiqiang, 2019. "Economic analysis and optimization of combined solar district heating technologies and systems," Energy, Elsevier, vol. 186(C).
    8. Kongtragool, Bancha & Wongwises, Somchai, 2003. "A review of solar-powered Stirling engines and low temperature differential Stirling engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 7(2), pages 131-154, April.
    9. Puech, Pascal & Tishkova, Victoria, 2011. "Thermodynamic analysis of a Stirling engine including regenerator dead volume," Renewable Energy, Elsevier, vol. 36(2), pages 872-878.
    10. Thombare, D.G. & Verma, S.K., 2008. "Technological development in the Stirling cycle engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 12(1), pages 1-38, January.
    11. Maraver, Daniel & Sin, Ana & Royo, Javier & Sebastián, Fernando, 2013. "Assessment of CCHP systems based on biomass combustion for small-scale applications through a review of the technology and analysis of energy efficiency parameters," Applied Energy, Elsevier, vol. 102(C), pages 1303-1313.
    12. Rogdakis, E.D. & Antonakos, G.D. & Koronaki, I.P., 2012. "Thermodynamic analysis and experimental investigation of a Solo V161 Stirling cogeneration unit," Energy, Elsevier, vol. 45(1), pages 503-511.
    13. Wang, Kui & Zhang, Yuanyuan & Sekelj, Gasper & Hopke, Philip K., 2019. "Economic analysis of a field monitored residential wood pellet boiler heating system in New York State," Renewable Energy, Elsevier, vol. 133(C), pages 500-511.
    14. Ferreira, Ana C. & Nunes, Manuel L. & Teixeira, José C.F. & Martins, Luís A.S.B. & Teixeira, Senhorinha F.C.F., 2016. "Thermodynamic and economic optimization of a solar-powered Stirling engine for micro-cogeneration purposes," Energy, Elsevier, vol. 111(C), pages 1-17.
    15. Barbieri, Enrico Saverio & Spina, Pier Ruggero & Venturini, Mauro, 2012. "Analysis of innovative micro-CHP systems to meet household energy demands," Applied Energy, Elsevier, vol. 97(C), pages 723-733.
    16. Ehtiwesh, Ismael A.S. & Coelho, Margarida C. & Sousa, Antonio C.M., 2016. "Exergetic and environmental life cycle assessment analysis of concentrated solar power plants," Renewable and Sustainable Energy Reviews, Elsevier, vol. 56(C), pages 145-155.
    17. González, Arnau & Riba, Jordi-Roger & Puig, Rita & Navarro, Pere, 2015. "Review of micro- and small-scale technologies to produce electricity and heat from Mediterranean forests׳ wood chips," Renewable and Sustainable Energy Reviews, Elsevier, vol. 43(C), pages 143-155.
    18. Bianchi, Michele & De Pascale, Andrea & Spina, Pier Ruggero, 2012. "Guidelines for residential micro-CHP systems design," Applied Energy, Elsevier, vol. 97(C), pages 673-685.
    19. Timoumi, Youssef & Tlili, Iskander & Ben Nasrallah, Sassi, 2008. "Performance optimization of Stirling engines," Renewable Energy, Elsevier, vol. 33(9), pages 2134-2144.
    20. Podesser, Erich, 1999. "Electricity production in rural villages with a biomass Stirling engine," Renewable Energy, Elsevier, vol. 16(1), pages 1049-1052.
    21. Badami, M. & Camillieri, F. & Portoraro, A. & Vigliani, E., 2014. "Energetic and economic assessment of cogeneration plants: A comparative design and experimental condition study," Energy, Elsevier, vol. 71(C), pages 255-262.
    22. Salomón, Marianne & Savola, Tuula & Martin, Andrew & Fogelholm, Carl-Johan & Fransson, Torsten, 2011. "Small-scale biomass CHP plants in Sweden and Finland," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(9), pages 4451-4465.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Xin, Feng & Tang, Bin & Zhao, Bin & Yang, Yanfeng & Liu, Wei & Liu, Zhichun, 2024. "Heat transfer enhancement of a Stirling engine heating tube with three-pronged slant rods under oscillatory flow," Energy, Elsevier, vol. 301(C).
    2. Carmela Perozziello & Lavinia Grosu & Bianca Maria Vaglieco, 2021. "Free-Piston Stirling Engine Technologies and Models: A Review," Energies, MDPI, vol. 14(21), pages 1-22, October.
    3. Majidniya, Mahdi & Remy, Benjamin & Boileau, Thierry & Zandi, Majid, 2021. "Free Piston Stirling Engine as a new heat recovery option for an Internal Reforming Solid Oxide Fuel Cell," Renewable Energy, Elsevier, vol. 171(C), pages 1188-1201.
    4. Krzysztof Sornek, 2020. "Prototypical Biomass-Fired Micro-Cogeneration Systems—Energy and Ecological Analysis," Energies, MDPI, vol. 13(15), pages 1-16, July.
    5. Mahdavi, Navid & Mojaver, Parisa & Khalilarya, Shahram, 2022. "Multi-objective optimization of power, CO2 emission and exergy efficiency of a novel solar-assisted CCHP system using RSM and TOPSIS coupled method," Renewable Energy, Elsevier, vol. 185(C), pages 506-524.
    6. David García & María-José Suárez & Eduardo Blanco & Jesús-Ignacio Prieto, 2022. "Experimental and Numerical Characterisation of a Non-Tubular Stirling Engine Heater for Biomass Applications," Sustainability, MDPI, vol. 14(24), pages 1-17, December.
    7. Li, Jie & Chang, Guozhang & Song, Ke & Hao, Bolun & Wang, Cuiping & Zhang, Jian & Yue, Guangxi & Hu, Shugang, 2023. "Influence of coal bottom ash additives on catalytic reforming of biomass pyrolysis gaseous tar and biochar/steam gasification reactivity," Renewable Energy, Elsevier, vol. 203(C), pages 434-444.
    8. Shulin Wang & Baiao Liu & Gang Xiao & Mingjiang Ni, 2021. "A Potential Method to Predict Performance of Positive Stirling Cycles Based on Reverse Ones," Energies, MDPI, vol. 14(21), pages 1-25, October.
    9. İncili, Veysel & Karaca Dolgun, Gülşah & Georgiev, Aleksandar & Keçebaş, Ali & Çetin, Numan Sabit, 2022. "Performance evaluation of novel photovoltaic and Stirling assisted hybrid micro combined heat and power system," Renewable Energy, Elsevier, vol. 189(C), pages 129-138.
    10. Kallio, Sonja & Siroux, Monica, 2022. "Exergy and exergo-economic analysis of a hybrid renewable energy system under different climate conditions," Renewable Energy, Elsevier, vol. 194(C), pages 396-414.
    11. Montazerinejad, H. & Eicker, U., 2022. "Recent development of heat and power generation using renewable fuels: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 165(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Pablo Jimenez Zabalaga & Evelyn Cardozo & Luis A. Choque Campero & Joseph Adhemar Araoz Ramos, 2020. "Performance Analysis of a Stirling Engine Hybrid Power System," Energies, MDPI, vol. 13(4), pages 1-38, February.
    2. Ferreira, Ana C. & Nunes, Manuel L. & Teixeira, José C.F. & Martins, Luís A.S.B. & Teixeira, Senhorinha F.C.F., 2016. "Thermodynamic and economic optimization of a solar-powered Stirling engine for micro-cogeneration purposes," Energy, Elsevier, vol. 111(C), pages 1-17.
    3. Schneider, T. & Müller, D. & Karl, J., 2020. "A review of thermochemical biomass conversion combined with Stirling engines for the small-scale cogeneration of heat and power," Renewable and Sustainable Energy Reviews, Elsevier, vol. 134(C).
    4. Bert, Juliette & Chrenko, Daniela & Sophy, Tonino & Le Moyne, Luis & Sirot, Frédéric, 2014. "Simulation, experimental validation and kinematic optimization of a Stirling engine using air and helium," Energy, Elsevier, vol. 78(C), pages 701-712.
    5. Zhu, Shunmin & Yu, Guoyao & Liang, Kun & Dai, Wei & Luo, Ercang, 2021. "A review of Stirling-engine-based combined heat and power technology," Applied Energy, Elsevier, vol. 294(C).
    6. Bert, Juliette & Chrenko, Daniela & Sophy, Tonino & Le Moyne, Luis & Sirot, Frédéric, 2012. "Zero dimensional finite-time thermodynamic, three zones numerical model of a generic Stirling and its experimental validation," Renewable Energy, Elsevier, vol. 47(C), pages 167-174.
    7. Marion, Michaël & Louahlia, Hasna & Gualous, Hamid, 2016. "Performances of a CHP Stirling system fuelled with glycerol," Renewable Energy, Elsevier, vol. 86(C), pages 182-191.
    8. Patel, Vivek & Savsani, Vimal, 2016. "Multi-objective optimization of a Stirling heat engine using TS-TLBO (tutorial training and self learning inspired teaching-learning based optimization) algorithm," Energy, Elsevier, vol. 95(C), pages 528-541.
    9. Carlos Ulloa & José Luis Míguez & Jacobo Porteiro & Pablo Eguía & Antón Cacabelos, 2013. "Development of a Transient Model of a Stirling-Based CHP System," Energies, MDPI, vol. 6(7), pages 1-19, June.
    10. Chmielewski, Adrian & Gumiński, Robert & Mączak, Jędrzej & Radkowski, Stanisław & Szulim, Przemysław, 2016. "Aspects of balanced development of RES and distributed micro-cogeneration use in Poland: Case study of a µCHP with Stirling engine," Renewable and Sustainable Energy Reviews, Elsevier, vol. 60(C), pages 930-952.
    11. Araoz, Joseph A. & Salomon, Marianne & Alejo, Lucio & Fransson, Torsten H., 2015. "Numerical simulation for the design analysis of kinematic Stirling engines," Applied Energy, Elsevier, vol. 159(C), pages 633-650.
    12. González, Arnau & Riba, Jordi-Roger & Puig, Rita & Navarro, Pere, 2015. "Review of micro- and small-scale technologies to produce electricity and heat from Mediterranean forests׳ wood chips," Renewable and Sustainable Energy Reviews, Elsevier, vol. 43(C), pages 143-155.
    13. Ahmadi, Mohammad H. & Ahmadi, Mohammad-Ali & Pourfayaz, Fathollah, 2017. "Thermal models for analysis of performance of Stirling engine: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 68(P1), pages 168-184.
    14. Cheng, Chin-Hsiang & Yang, Hang-Suin, 2011. "Analytical model for predicting the effect of operating speed on shaft power output of Stirling engines," Energy, Elsevier, vol. 36(10), pages 5899-5908.
    15. Buliński, Zbigniew & Szczygieł, Ireneusz & Krysiński, Tomasz & Stanek, Wojciech & Czarnowska, Lucyna & Gładysz, Paweł & Kabaj, Adam, 2017. "Finite time thermodynamic analysis of small alpha-type Stirling engine in non-ideal polytropic conditions for recovery of LNG cryogenic exergy," Energy, Elsevier, vol. 141(C), pages 2559-2571.
    16. Franco Cotana & Antonio Messineo & Alessandro Petrozzi & Valentina Coccia & Gianluca Cavalaglio & Andrea Aquino, 2014. "Comparison of ORC Turbine and Stirling Engine to Produce Electricity from Gasified Poultry Waste," Sustainability, MDPI, vol. 6(9), pages 1-16, August.
    17. Ziviani, Davide & Beyene, Asfaw & Venturini, Mauro, 2014. "Advances and challenges in ORC systems modeling for low grade thermal energy recovery," Applied Energy, Elsevier, vol. 121(C), pages 79-95.
    18. Chahartaghi, Mahmood & Sheykhi, Mohammad, 2019. "Energy, environmental and economic evaluations of a CCHP system driven by Stirling engine with helium and hydrogen as working gases," Energy, Elsevier, vol. 174(C), pages 1251-1266.
    19. Cheng, Chin-Hsiang & Yang, Hang-Suin & Keong, Lam, 2013. "Theoretical and experimental study of a 300-W beta-type Stirling engine," Energy, Elsevier, vol. 59(C), pages 590-599.
    20. Cullen, Barry & McGovern, Jim, 2010. "Energy system feasibility study of an Otto cycle/Stirling cycle hybrid automotive engine," Energy, Elsevier, vol. 35(2), pages 1017-1023.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:renene:v:154:y:2020:i:c:p:581-597. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/renewable-energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.