IDEAS home Printed from https://ideas.repec.org/a/eee/renene/v147y2020ip1p356-373.html
   My bibliography  Save this article

Climatic and seasonal suitability of phase change materials coupled with night ventilation for office buildings in Western China

Author

Listed:
  • Liu, Jiang
  • Liu, Yan
  • Yang, Liu
  • Liu, Tang
  • Zhang, Chen
  • Dong, Hong

Abstract

Phase change material (PCM) coupled with night ventilation (NV) is regarded as a promising cooling strategy. The suitability of PCM coupled with NV in transition and hot seasons of 10 cities in Western China was investigated based on a non-air-conditioned office building. The optimum phase change temperature (PCT) and the cooling potential of PCM coupled with NV in transition and hot seasons were determined by numerical investigations using EnergyPlus. The results showed that the optimum PCT for the 10 selected cities varied from 23 °C to 29 °C. PCM coupled with NV was suitable for application in all of the selected cities, but the PCM strategy was the best choice for the transition season in cities in severe cold zone. Applying PCM coupled with NV strategy could reduce the discomfort hours in the transition season by at least 16% compared with NV alone. In addition, the favorable outdoor air dry-bulb temperature (Tout) for the application of PCM coupled with NV was obtained for the selected cities in Western China, which had the following characteristics: (1) the diurnal temperature difference (ΔT) exceeded 6.8 °C, (2) the average value (Tave) was close to 27 °C, (3) the minimum value (Tmin) was 2.7 °C lower than the optimum PCT and the maximum value (Tmax) was 1.7 °C higher than the optimum PCT.

Suggested Citation

  • Liu, Jiang & Liu, Yan & Yang, Liu & Liu, Tang & Zhang, Chen & Dong, Hong, 2020. "Climatic and seasonal suitability of phase change materials coupled with night ventilation for office buildings in Western China," Renewable Energy, Elsevier, vol. 147(P1), pages 356-373.
    • Handle: RePEc:eee:renene:v:147:y:2020:i:p1:p:356-373
    DOI: 10.1016/j.renene.2019.08.069
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S096014811931256X
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.renene.2019.08.069?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Mi, Xuming & Liu, Ran & Cui, Hongzhi & Memon, Shazim Ali & Xing, Feng & Lo, Yiu, 2016. "Energy and economic analysis of building integrated with PCM in different cities of China," Applied Energy, Elsevier, vol. 175(C), pages 324-336.
    2. Zhou, D. & Zhao, C.Y. & Tian, Y., 2012. "Review on thermal energy storage with phase change materials (PCMs) in building applications," Applied Energy, Elsevier, vol. 92(C), pages 593-605.
    3. Kuznik, Frédéric & David, Damien & Johannes, Kevyn & Roux, Jean-Jacques, 2011. "A review on phase change materials integrated in building walls," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(1), pages 379-391, January.
    4. Zhou, Guobing & Yang, Yongping & Wang, Xin & Zhou, Shaoxiang, 2009. "Numerical analysis of effect of shape-stabilized phase change material plates in a building combined with night ventilation," Applied Energy, Elsevier, vol. 86(1), pages 52-59, January.
    5. Ramakrishnan, Sayanthan & Wang, Xiaoming & Sanjayan, Jay & Wilson, John, 2017. "Thermal performance assessment of phase change material integrated cementitious composites in buildings: Experimental and numerical approach," Applied Energy, Elsevier, vol. 207(C), pages 654-664.
    6. Ramakrishnan, Sayanthan & Wang, Xiaoming & Sanjayan, Jay & Wilson, John, 2017. "Thermal performance of buildings integrated with phase change materials to reduce heat stress risks during extreme heatwave events," Applied Energy, Elsevier, vol. 194(C), pages 410-421.
    7. Solgi, Ebrahim & Fayaz, Rima & Kari, Behrouz Mohammad, 2016. "Cooling load reduction in office buildings of hot-arid climate, combining phase change materials and night purge ventilation," Renewable Energy, Elsevier, vol. 85(C), pages 725-731.
    8. Liu, Zhijian & Liu, Yuanwei & He, Bao-Jie & Xu, Wei & Jin, Guangya & Zhang, Xutao, 2019. "Application and suitability analysis of the key technologies in nearly zero energy buildings in China," Renewable and Sustainable Energy Reviews, Elsevier, vol. 101(C), pages 329-345.
    9. Artmann, N. & Manz, H. & Heiselberg, P., 2007. "Climatic potential for passive cooling of buildings by night-time ventilation in Europe," Applied Energy, Elsevier, vol. 84(2), pages 187-201, February.
    10. Kuznik, Frédéric & Virgone, Joseph & Johannes, Kevyn, 2011. "In-situ study of thermal comfort enhancement in a renovated building equipped with phase change material wallboard," Renewable Energy, Elsevier, vol. 36(5), pages 1458-1462.
    11. Zeng, Cheng & Liu, Shuli & Shukla, Ashish, 2017. "Adaptability research on phase change materials based technologies in China," Renewable and Sustainable Energy Reviews, Elsevier, vol. 73(C), pages 145-158.
    12. Barzin, Reza & Chen, John J.J. & Young, Brent R. & Farid, Mohammed M., 2015. "Application of PCM energy storage in combination with night ventilation for space cooling," Applied Energy, Elsevier, vol. 158(C), pages 412-421.
    13. AL-Saadi, Saleh Nasser & Zhai, Zhiqiang (John), 2013. "Modeling phase change materials embedded in building enclosure: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 21(C), pages 659-673.
    14. Zhou, D. & Shire, G.S.F. & Tian, Y., 2014. "Parametric analysis of influencing factors in Phase Change Material Wallboard (PCMW)," Applied Energy, Elsevier, vol. 119(C), pages 33-42.
    15. Waqas, Adeel & Ud Din, Zia, 2013. "Phase change material (PCM) storage for free cooling of buildings—A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 18(C), pages 607-625.
    16. Li, Danny H.W. & Yang, Liu & Lam, Joseph C., 2013. "Zero energy buildings and sustainable development implications – A review," Energy, Elsevier, vol. 54(C), pages 1-10.
    17. Panayiotou, G.P. & Kalogirou, S.A. & Tassou, S.A., 2016. "Evaluation of the application of Phase Change Materials (PCM) on the envelope of a typical dwelling in the Mediterranean region," Renewable Energy, Elsevier, vol. 97(C), pages 24-32.
    18. A.M. Fogheri, 2015. "Energy Efficiency in Public Buildings," Rivista economica del Mezzogiorno, Società editrice il Mulino, issue 3-4, pages 763-784.
    19. Marine Auzeby & Shen Wei & Chris Underwood & Jess Tindall & Chao Chen & Haoshu Ling & Richard Buswell, 2016. "Effectiveness of Using Phase Change Materials on Reducing Summer Overheating Issues in UK Residential Buildings with Identification of Influential Factors," Energies, MDPI, vol. 9(8), pages 1-16, August.
    20. Cascone, Ylenia & Capozzoli, Alfonso & Perino, Marco, 2018. "Optimisation analysis of PCM-enhanced opaque building envelope components for the energy retrofitting of office buildings in Mediterranean climates," Applied Energy, Elsevier, vol. 211(C), pages 929-953.
    21. Shaviv, Edna & Yezioro, Abraham & Capeluto, Isaac G, 2001. "Thermal mass and night ventilation as passive cooling design strategy," Renewable Energy, Elsevier, vol. 24(3), pages 445-452.
    22. Roman, Kibria K. & O'Brien, Timothy & Alvey, Jedediah B. & Woo, OhJin, 2016. "Simulating the effects of cool roof and PCM (phase change materials) based roof to mitigate UHI (urban heat island) in prominent US cities," Energy, Elsevier, vol. 96(C), pages 103-117.
    23. Liu, Yan & Yang, Liu & Hou, Liqiang & Li, Shiyang & Yang, Jian & Wang, Qiuwang, 2017. "A porous building approach for modelling flow and heat transfer around and inside an isolated building on night ventilation and thermal mass," Energy, Elsevier, vol. 141(C), pages 1914-1927.
    24. Zhou, Guobing & Zhang, Yinping & Zhang, Qunli & Lin, Kunping & Di, Hongfa, 2007. "Performance of a hybrid heating system with thermal storage using shape-stabilized phase-change material plates," Applied Energy, Elsevier, vol. 84(10), pages 1068-1077, October.
    25. Medved, Sašo & Babnik, Miha & Vidrih, Boris & Arkar, Ciril, 2014. "Parametric study on the advantages of weather-predicted control algorithm of free cooling ventilation system," Energy, Elsevier, vol. 73(C), pages 80-87.
    26. Chwieduk, Dorota A., 2013. "Dynamics of external wall structures with a PCM (phase change materials) in high latitude countries," Energy, Elsevier, vol. 59(C), pages 301-313.
    27. Sadineni, Suresh B. & Madala, Srikanth & Boehm, Robert F., 2011. "Passive building energy savings: A review of building envelope components," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(8), pages 3617-3631.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Al-Yasiri, Qudama & Alktranee, Mohammed & Szabó, Márta & Arıcı, Müslüm, 2023. "Building envelope-enhanced phase change material and night ventilation: Effect of window orientation and window-to-wall ratio on indoor temperature," Renewable Energy, Elsevier, vol. 218(C).
    2. Li, Weilin & Jing, Mingyi & Li, Rufei & Gao, Junxi & Zhu, Jiayin & Li, Ruixin, 2023. "Study of the optimal placement of phase change materials in existing buildings for cooling load reduction - Take the Central Plain of China as an example," Renewable Energy, Elsevier, vol. 209(C), pages 71-84.
    3. Almas Sheriyev & Shazim Ali Memon & Indira Adilkhanova & Jong Kim, 2021. "Effect of Phase Change Materials on the Thermal Performance of Residential Building Located in Different Cities of a Tropical Rainforest Climate Zone," Energies, MDPI, vol. 14(9), pages 1-22, May.
    4. Rongda Ye & Xiaoming Fang & Zhengguo Zhang, 2021. "Numerical Study on Energy-Saving Performance of a New Type of Phase Change Material Room," Energies, MDPI, vol. 14(13), pages 1-18, June.
    5. Köse Murathan, Eda & Manioğlu, Gülten, 2020. "Evaluation of phase change materials used in building components for conservation of energy in buildings in hot dry climatic regions," Renewable Energy, Elsevier, vol. 162(C), pages 1919-1930.
    6. Chen, Zhaoxin & Li, Jiaxuan & Tang, Guoqiang & Zhang, Jiahao & Zhang, Donghai & Gao, Penghui, 2024. "High-efficiency heating and cooling technology with embedded pipes in buildings and underground structures: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 192(C).
    7. Piselli, Cristina & Prabhakar, Mohit & de Gracia, Alvaro & Saffari, Mohammad & Pisello, Anna Laura & Cabeza, Luisa F., 2020. "Optimal control of natural ventilation as passive cooling strategy for improving the energy performance of building envelope with PCM integration," Renewable Energy, Elsevier, vol. 162(C), pages 171-181.
    8. Yi Gao & Zhiguo Li & Kashif Khan, 2019. "A Study on the Relationship between Paradox Cognition, Green Industrial Production, and Corporate Performance," Sustainability, MDPI, vol. 11(23), pages 1-18, November.
    9. Yan, Tian & Zhou, Xuan & Xu, Xinhua & Yu, Jinghua & Li, Xianting, 2022. "Parametric analysis on performances of the pipe-encapsulated PCM (PenPCM) wall system coupled with gravity heat-pipe and nocturnal radiant cooler," Renewable Energy, Elsevier, vol. 196(C), pages 161-180.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Lamrani, B. & Johannes, K. & Kuznik, F., 2021. "Phase change materials integrated into building walls: An updated review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 140(C).
    2. Mavrigiannaki, A. & Ampatzi, E., 2016. "Latent heat storage in building elements: A systematic review on properties and contextual performance factors," Renewable and Sustainable Energy Reviews, Elsevier, vol. 60(C), pages 852-866.
    3. Barzin, Reza & Chen, John J.J. & Young, Brent R. & Farid, Mohammed M., 2015. "Application of PCM energy storage in combination with night ventilation for space cooling," Applied Energy, Elsevier, vol. 158(C), pages 412-421.
    4. Alizadeh, M. & Sadrameli, S.M., 2016. "Development of free cooling based ventilation technology for buildings: Thermal energy storage (TES) unit, performance enhancement techniques and design considerations – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 58(C), pages 619-645.
    5. Saffari, Mohammad & de Gracia, Alvaro & Ushak, Svetlana & Cabeza, Luisa F., 2017. "Passive cooling of buildings with phase change materials using whole-building energy simulation tools: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 1239-1255.
    6. Akeiber, Hussein & Nejat, Payam & Majid, Muhd Zaimi Abd. & Wahid, Mazlan A. & Jomehzadeh, Fatemeh & Zeynali Famileh, Iman & Calautit, John Kaiser & Hughes, Ben Richard & Zaki, Sheikh Ahmad, 2016. "A review on phase change material (PCM) for sustainable passive cooling in building envelopes," Renewable and Sustainable Energy Reviews, Elsevier, vol. 60(C), pages 1470-1497.
    7. Zeinelabdein, Rami & Omer, Siddig & Gan, Guohui, 2018. "Critical review of latent heat storage systems for free cooling in buildings," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 2843-2868.
    8. Lei, Jiawei & Yang, Jinglei & Yang, En-Hua, 2016. "Energy performance of building envelopes integrated with phase change materials for cooling load reduction in tropical Singapore," Applied Energy, Elsevier, vol. 162(C), pages 207-217.
    9. Saafi, Khawla & Daouas, Naouel, 2019. "Energy and cost efficiency of phase change materials integrated in building envelopes under Tunisia Mediterranean climate," Energy, Elsevier, vol. 187(C).
    10. Lizana, Jesús & Chacartegui, Ricardo & Barrios-Padura, Angela & Ortiz, Carlos, 2018. "Advanced low-carbon energy measures based on thermal energy storage in buildings: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 3705-3749.
    11. Pirasaci, Tolga, 2020. "Investigation of phase state and heat storage form of the phase change material (PCM) layer integrated into the exterior walls of the residential-apartment during heating season," Energy, Elsevier, vol. 207(C).
    12. Saffari, Mohammad & de Gracia, Alvaro & Fernández, Cèsar & Cabeza, Luisa F., 2017. "Simulation-based optimization of PCM melting temperature to improve the energy performance in buildings," Applied Energy, Elsevier, vol. 202(C), pages 420-434.
    13. Alam, Morshed & Zou, Patrick X.W. & Sanjayan, Jay & Ramakrishnan, Sayanthan, 2019. "Energy saving performance assessment and lessons learned from the operation of an active phase change materials system in a multi-storey building in Melbourne," Applied Energy, Elsevier, vol. 238(C), pages 1582-1595.
    14. Soares, N. & Santos, P. & Gervásio, H. & Costa, J.J. & Simões da Silva, L., 2017. "Energy efficiency and thermal performance of lightweight steel-framed (LSF) construction: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 78(C), pages 194-209.
    15. Kenisarin, Murat & Mahkamov, Khamid, 2016. "Passive thermal control in residential buildings using phase change materials," Renewable and Sustainable Energy Reviews, Elsevier, vol. 55(C), pages 371-398.
    16. Liu, Yan & Yang, Liu & Hou, Liqiang & Li, Shiyang & Yang, Jian & Wang, Qiuwang, 2017. "A porous building approach for modelling flow and heat transfer around and inside an isolated building on night ventilation and thermal mass," Energy, Elsevier, vol. 141(C), pages 1914-1927.
    17. Bimaganbetova, Madina & Memon, Shazim Ali & Sheriyev, Almas, 2020. "Performance evaluation of phase change materials suitable for cities representing the whole tropical savanna climate region," Renewable Energy, Elsevier, vol. 148(C), pages 402-416.
    18. Souayfane, Farah & Biwole, Pascal Henry & Fardoun, Farouk & Achard, Patrick, 2019. "Energy performance and economic analysis of a TIM-PCM wall under different climates," Energy, Elsevier, vol. 169(C), pages 1274-1291.
    19. Monika Gandhi & Ashok Kumar & Rajasekar Elangovan & Chandan Swaroop Meena & Kishor S. Kulkarni & Anuj Kumar & Garima Bhanot & Nishant R. Kapoor, 2020. "A Review on Shape-Stabilized Phase Change Materials for Latent Energy Storage in Buildings," Sustainability, MDPI, vol. 12(22), pages 1-17, November.
    20. Enghok Leang & Pierre Tittelein & Laurent Zalewski & Stéphane Lassue, 2020. "Impact of a Composite Trombe Wall Incorporating Phase Change Materials on the Thermal Behavior of an Individual House with Low Energy Consumption," Energies, MDPI, vol. 13(18), pages 1-32, September.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:renene:v:147:y:2020:i:p1:p:356-373. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/renewable-energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.