IDEAS home Printed from https://ideas.repec.org/a/eee/renene/v106y2017icp24-36.html
   My bibliography  Save this article

CFD and experimental investigation of flat plate solar water heating system under steady state condition

Author

Listed:
  • Gunjo, Dawit Gudeta
  • Mahanta, Pinakeswar
  • Robi, P.S.

Abstract

The absorber plate and outlet water temperature of a solar flat plate collector with straight riser and header arrangement is investigated. The effect of different operating parameters, viz., inlet water temperature, solar insolation, ambient temperature, and mass flow rate on the outlet water temperature and thermal efficiency were studied. Both the closed as well as open loop solar water heating system is considered for the present investigation. It is observed that the thermal efficiency of the solar water heating system increases with ambient temperature, solar insolation, and mass flow rate of water. However, thermal efficiency decreases as inlet water temperature increases. Numerical simulations were carried out using a 3-dimensional computational fluid dynamics (CFD) to predict the outlet water and absorber plate temperatures using the experimental values of solar insolation, ambient temperature and inlet water temperature within one hour interval. The CFD results were validated with the experimental results. It was found that the developed model could predict the outlet water and absorber plate temperature of the heating system with reasonable accuracy.

Suggested Citation

  • Gunjo, Dawit Gudeta & Mahanta, Pinakeswar & Robi, P.S., 2017. "CFD and experimental investigation of flat plate solar water heating system under steady state condition," Renewable Energy, Elsevier, vol. 106(C), pages 24-36.
    • Handle: RePEc:eee:renene:v:106:y:2017:i:c:p:24-36
    DOI: 10.1016/j.renene.2016.12.041
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0960148116310977
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.renene.2016.12.041?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Dagdougui, Hanane & Ouammi, Ahmed & Robba, Michela & Sacile, Roberto, 2011. "Thermal analysis and performance optimization of a solar water heater flat plate collector: Application to Tétouan (Morocco)," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(1), pages 630-638, January.
    2. Bilgen, E. & Bakeka, B.J.D., 2008. "Solar collector systems to provide hot air in rural applications," Renewable Energy, Elsevier, vol. 33(7), pages 1461-1468.
    3. Kalogirou, Soteris A., 2014. "Flat-plate collector construction and system configuration to optimize the thermosiphonic effect," Renewable Energy, Elsevier, vol. 67(C), pages 202-206.
    4. Gadi, Mohamed B., 2000. "Design and simulation of a new energy-conscious system (CFD and solar simulation)," Applied Energy, Elsevier, vol. 65(1-4), pages 251-256, April.
    5. Martinopoulos, G. & Missirlis, D. & Tsilingiridis, G. & Yakinthos, K. & Kyriakis, N., 2010. "CFD modeling of a polymer solar collector," Renewable Energy, Elsevier, vol. 35(7), pages 1499-1508.
    6. Baños, R. & Manzano-Agugliaro, F. & Montoya, F.G. & Gil, C. & Alcayde, A. & Gómez, J., 2011. "Optimization methods applied to renewable and sustainable energy: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(4), pages 1753-1766, May.
    7. Janjai, S. & Esper, A. & Mühlbauer, W., 2000. "Modelling the performance of a large area plastic solar collector," Renewable Energy, Elsevier, vol. 21(3), pages 363-376.
    8. Selmi, Mohamed & Al-Khawaja, Mohammed J. & Marafia, Abdulhamid, 2008. "Validation of CFD simulation for flat plate solar energy collector," Renewable Energy, Elsevier, vol. 33(3), pages 383-387.
    9. Keyanpour-Rad, M. & Haghgou, H.R. & Bahar, F. & Afshari, E., 2000. "Feasibility study of the application of solar heating systems in Iran," Renewable Energy, Elsevier, vol. 20(3), pages 333-345.
    10. Gadi, Mohamed B., 2000. "Design and simulation of a new energy conscious system, (basic concept)," Applied Energy, Elsevier, vol. 65(1-4), pages 349-353, April.
    11. Gadi, Mohamed B., 2000. "Design and simulation of a new energy conscious system, (ventilation and thermal performance simulation)," Applied Energy, Elsevier, vol. 65(1-4), pages 355-366, April.
    12. Shariah, Adnan & Shalabi, Bassam, 1997. "Optimal design for a thermosyphon solar water heater," Renewable Energy, Elsevier, vol. 11(3), pages 351-361.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Das, Debayan & Lukose, Leo & Basak, Tanmay, 2018. "Role of multiple solar heaters along the walls for the thermal management during natural convection in square and triangular cavities," Renewable Energy, Elsevier, vol. 121(C), pages 205-229.
    2. Americano da Costa, Marcus V. & Narasimhan, Arunkumar & Guillen, Diego & Joseph, Babu & Goswami, D. Yogi, 2020. "Generalized distributed state space model of a CSP plant for simulation and control applications: Single-phase flow validation," Renewable Energy, Elsevier, vol. 153(C), pages 36-48.
    3. Farshad, Seyyed Ali & Sheikholeslami, M., 2019. "Nanofluid flow inside a solar collector utilizing twisted tape considering exergy and entropy analysis," Renewable Energy, Elsevier, vol. 141(C), pages 246-258.
    4. Ashour, Amr Fathy & El-Awady, Ahmed T. & Tawfik, Mohsen A., 2022. "Numerical investigation on the thermal performance of a flat plate solar collector using ZnO & CuO water nanofluids under Egyptian weathering conditions," Energy, Elsevier, vol. 240(C).
    5. Gunjo, Dawit Gudeta & Mahanta, Pinakeswar & Robi, Puthuveettil Sreedharan, 2017. "Exergy and energy analysis of a novel type solar collector under steady state condition: Experimental and CFD analysis," Renewable Energy, Elsevier, vol. 114(PB), pages 655-669.
    6. Lyu, Yuanli & Liu, Wenjie & Chow, Tin-tai & Su, Hua & Qi, Xuejun, 2019. "Pipe-work optimization of water flow window," Renewable Energy, Elsevier, vol. 139(C), pages 136-146.
    7. Elguezabal, P. & Lopez, A. & Blanco, J.M. & Chica, J.A., 2020. "CFD model-based analysis and experimental assessment of key design parameters for an integrated unglazed metallic thermal collector façade," Renewable Energy, Elsevier, vol. 146(C), pages 1766-1780.
    8. Ma, Ruihua & Ma, Dongyan & Ma, Ruijiang & Long, Enshen, 2022. "Theoretical and experimental analysis of temperature variation of V–Ti black ceramic solar collector," Renewable Energy, Elsevier, vol. 194(C), pages 1153-1162.
    9. Sheikholeslami, M. & Farshad, Seyyed Ali, 2021. "Investigation of solar collector system with turbulator considering hybrid nanoparticles," Renewable Energy, Elsevier, vol. 171(C), pages 1128-1158.
    10. Radwan, Ali & Abo-Zahhad, Essam M. & El-Sharkawy, Ibrahim I. & Said, Zafar & Abdelrehim, Osama & Memon, Saim & Cheng, Ping & Soliman, Ahmed Saad, 2024. "Thermal analysis of a bifacial vacuum-based solar thermal collector," Energy, Elsevier, vol. 294(C).
    11. Peru Elguezabal & Alex Lopez & Jesus Maria Blanco & Jose Antonio Chica, 2020. "Assessment on the Efficiency of an Active Solar Thermal Facade: Study of the Effect of Dynamic Parameters and Experimental Analysis When Coupled/Uncoupled to a Heat Pump," Energies, MDPI, vol. 13(3), pages 1-21, January.
    12. Karimi, Mohammad Sadjad & Fazelpour, Farivar & Rosen, Marc A. & Shams, Mehrzad, 2019. "Comparative study of solar-powered underfloor heating system performance in distinctive climates," Renewable Energy, Elsevier, vol. 130(C), pages 524-535.
    13. Zhou, Liqun & Wang, Yiping & Huang, Qunwu, 2019. "CFD investigation of a new flat plate collector with additional front side transparent insulation for use in cold regions," Renewable Energy, Elsevier, vol. 138(C), pages 754-763.
    14. Jouybari, H. Javaniyan & Saedodin, S. & Zamzamian, A. & Nimvari, M. Eshagh & Wongwises, S., 2017. "Effects of porous material and nanoparticles on the thermal performance of a flat plate solar collector: An experimental study," Renewable Energy, Elsevier, vol. 114(PB), pages 1407-1418.
    15. Lugo, S. & García-Valladares, O. & Best, R. & Hernández, J. & Hernández, F., 2019. "Numerical simulation and experimental validation of an evacuated solar collector heating system with gas boiler backup for industrial process heating in warm climates," Renewable Energy, Elsevier, vol. 139(C), pages 1120-1132.
    16. Korres, Dimitrios & Tzivanidis, Christos, 2018. "A new mini-CPC with a U-type evacuated tube under thermal and optical investigation," Renewable Energy, Elsevier, vol. 128(PB), pages 529-540.
    17. Moldovan, Macedon & Rusea, Ioana & Visa, Ion, 2021. "Optimising the thickness of the water layer in a triangle solar thermal collector," Renewable Energy, Elsevier, vol. 173(C), pages 381-388.
    18. Bayón-Cueli, C. & Barbón, A. & Bayón, L. & Barbón, N., 2020. "A cost-energy based methodology for small-scale linear Fresnel reflectors on flat roofs of urban buildings," Renewable Energy, Elsevier, vol. 146(C), pages 944-959.
    19. William Quitiaquez & José Estupiñán-Campos & César Nieto-Londoño & Patricio Quitiaquez, 2023. "CFD Analysis of Heat Transfer Enhancement in a Flat-Plate Solar Collector/Evaporator with Different Geometric Variations in the Cross Section," Energies, MDPI, vol. 16(15), pages 1-15, August.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Gunjo, Dawit Gudeta & Mahanta, Pinakeswar & Robi, Puthuveettil Sreedharan, 2017. "Exergy and energy analysis of a novel type solar collector under steady state condition: Experimental and CFD analysis," Renewable Energy, Elsevier, vol. 114(PB), pages 655-669.
    2. Subiantoro, Alison & Ooi, Kim Tiow, 2013. "Analytical models for the computation and optimization of single and double glazing flat plate solar collectors with normal and small air gap spacing," Applied Energy, Elsevier, vol. 104(C), pages 392-399.
    3. Hadavand, M. & Yaghoubi, M., 2008. "Thermal behavior of curved roof buildings exposed to solar radiation and wind flow for various orientations," Applied Energy, Elsevier, vol. 85(8), pages 663-679, August.
    4. Oropeza-Perez, Ivan & Østergaard, Poul Alberg, 2014. "Potential of natural ventilation in temperate countries – A case study of Denmark," Applied Energy, Elsevier, vol. 114(C), pages 520-530.
    5. Zhang, Haihua & Yang, Dong & Tam, Vivian W.Y. & Tao, Yao & Zhang, Guomin & Setunge, Sujeeva & Shi, Long, 2021. "A critical review of combined natural ventilation techniques in sustainable buildings," Renewable and Sustainable Energy Reviews, Elsevier, vol. 141(C).
    6. Cruz-Peragon, F. & Palomar, J.M. & Casanova, P.J. & Dorado, M.P. & Manzano-Agugliaro, F., 2012. "Characterization of solar flat plate collectors," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(3), pages 1709-1720.
    7. Gunjo, Dawit Gudeta & Jena, Smruti Ranjan & Mahanta, Pinakeswar & Robi, P.S., 2018. "Melting enhancement of a latent heat storage with dispersed Cu, CuO and Al2O3 nanoparticles for solar thermal application," Renewable Energy, Elsevier, vol. 121(C), pages 652-665.
    8. Bracco, Stefano & Delfino, Federico & Pampararo, Fabio & Robba, Michela & Rossi, Mansueto, 2013. "The University of Genoa smart polygeneration microgrid test-bed facility: The overall system, the technologies and the research challenges," Renewable and Sustainable Energy Reviews, Elsevier, vol. 18(C), pages 442-459.
    9. Herrando, María & Fantoni, Guillermo & Cubero, Ana & Simón-Allué, Raquel & Guedea, Isabel & Fueyo, Norberto, 2023. "Numerical analysis of the fluid flow and heat transfer of a hybrid PV-thermal collector and performance assessment," Renewable Energy, Elsevier, vol. 209(C), pages 122-132.
    10. Missirlis, D. & Martinopoulos, G. & Tsilingiridis, G. & Yakinthos, K. & Kyriakis, N., 2014. "Investigation of the heat transfer behaviour of a polymer solar collector for different manifold configurations," Renewable Energy, Elsevier, vol. 68(C), pages 715-723.
    11. Farshad, Seyyed Ali & Sheikholeslami, M., 2019. "Nanofluid flow inside a solar collector utilizing twisted tape considering exergy and entropy analysis," Renewable Energy, Elsevier, vol. 141(C), pages 246-258.
    12. Craig, K.J. & Moghimi, M.A. & Rungasamy, A.E. & Marsberg, J. & Meyer, J.P., 2016. "Finite-volume ray tracing using Computational Fluid Dynamics in linear focus CSP applications," Applied Energy, Elsevier, vol. 183(C), pages 241-256.
    13. Cerón, J.F. & Pérez-García, J. & Solano, J.P. & García, A. & Herrero-Martín, R., 2015. "A coupled numerical model for tube-on-sheet flat-plate solar liquid collectors. Analysis and validation of the heat transfer mechanisms," Applied Energy, Elsevier, vol. 140(C), pages 275-287.
    14. Dagdougui, Hanane & Ouammi, Ahmed & Robba, Michela & Sacile, Roberto, 2011. "Thermal analysis and performance optimization of a solar water heater flat plate collector: Application to Tétouan (Morocco)," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(1), pages 630-638, January.
    15. Herrando, María & Ramos, Alba & Zabalza, Ignacio & Markides, Christos N., 2019. "A comprehensive assessment of alternative absorber-exchanger designs for hybrid PVT-water collectors," Applied Energy, Elsevier, vol. 235(C), pages 1583-1602.
    16. Sakhaei, Seyed Ali & Valipour, Mohammad Sadegh, 2019. "Performance enhancement analysis of The flat plate collectors: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 102(C), pages 186-204.
    17. Saadatian, Omidreza & Haw, Lim Chin & Sopian, K. & Sulaiman, M.Y., 2012. "Review of windcatcher technologies," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(3), pages 1477-1495.
    18. Tian, Y. & Zhao, C.Y., 2013. "A review of solar collectors and thermal energy storage in solar thermal applications," Applied Energy, Elsevier, vol. 104(C), pages 538-553.
    19. Buker, Mahmut Sami & Riffat, Saffa B., 2015. "Building integrated solar thermal collectors – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 51(C), pages 327-346.
    20. Korres, Dimitrios & Tzivanidis, Christos, 2018. "A new mini-CPC with a U-type evacuated tube under thermal and optical investigation," Renewable Energy, Elsevier, vol. 128(PB), pages 529-540.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:renene:v:106:y:2017:i:c:p:24-36. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/renewable-energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.