IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v289y2024ics036054422303462x.html
   My bibliography  Save this article

Power and efficiency improvement of SI engine fueled with boosted producer gas-methane blends and LIVC-miller cycle strategy: Thermodynamic and optimization studies

Author

Listed:
  • Jena, Priyaranjan
  • Tirkey, Jeewan Vachan

Abstract

An appealing alternative solution for lowering both reliance on power grid and pollution is by adopting decentralized power generation using gasifier-engine integrated systems. However, the utilization of gasification-derived producer gas (PG) leads to low engine power output and efficiency as compared to conventional fuels. This pertains to its low Calorific value(CV) and low flame-speed. Therefore, this simulation study aims to simulate and investigate the improvements in these parameters by inspecting various boosted-intake pressures and blends of high-CV methane with PG as inputs along with the implementation of Late inlet valve close(LIVC)-Miller cycle strategy on a 1500 RPM Dual-fuel(DF) SI engine model. Quasi-dimensional thermodynamic modelling (QDTM) was applied to simulate this performance and emission investigation by considering Sewage sludge-based PG (SSPG) as the PG variant. Best operational input settings were found using the Response Surface Methodology(RSM)-based multi-objective optimization. These optimal inputs were 3 bars of Pressure at intake valve closure (PIVC), 76.94 % SSPG-blend, and 77.32⁰ (ABDC) LIVC. The responses were correspondingly predicted as 40.46 % ITE, 21.35 bars IMEP, 16.8 kW BP, 20.04 bars BMEP, 9.48 MJ/kWh BSEC, with 0.08 V% CO and 3094 ppm NO emissions. Finally, with the ANOVA-based analysis, a 0.712 composite desirability was achieved with 95 % confidence level.

Suggested Citation

  • Jena, Priyaranjan & Tirkey, Jeewan Vachan, 2024. "Power and efficiency improvement of SI engine fueled with boosted producer gas-methane blends and LIVC-miller cycle strategy: Thermodynamic and optimization studies," Energy, Elsevier, vol. 289(C).
    • Handle: RePEc:eee:energy:v:289:y:2024:i:c:s036054422303462x
    DOI: 10.1016/j.energy.2023.130068
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S036054422303462X
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2023.130068?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Saiteja, Pajarla & Ashok, B., 2022. "Study on interactive effects of CRDi engine operating parameters through RSM based multi-objective optimization technique for biofuel application," Energy, Elsevier, vol. 255(C).
    2. Zhao, Jinxing & Fu, Rui & Wang, Sen & Xu, Hongchang & Yuan, Zhiyuan, 2022. "Fuel economy improvement of a turbocharged gasoline SI engine through combining cooled EGR and high compression ratio," Energy, Elsevier, vol. 239(PE).
    3. Aghaali, Habib & Ångström, Hans-Erik, 2015. "A review of turbocompounding as a waste heat recovery system for internal combustion engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 49(C), pages 813-824.
    4. Qiao, Junhao & Liu, Jingping & Liang, Jichao & Jia, Dongdong & Wang, Rumin & Shen, Dazi & Duan, Xiongbo, 2023. "Experimental investigation the effects of Miller cycle coupled with asynchronous intake valves on cycle-to-cycle variations and performance of the SI engine," Energy, Elsevier, vol. 263(PD).
    5. Percy, A. Jemila & Edwin, M., 2023. "Studies on the performance and emission characteristics of a dual fuel VCR engine using producer gas as secondary fuel: An optimization approach using response surface methodology," Energy, Elsevier, vol. 263(PA).
    6. Kan, Xiang & Zhou, Dezhi & Yang, Wenming & Zhai, Xiaoqiang & Wang, Chi-Hwa, 2018. "An investigation on utilization of biogas and syngas produced from biomass waste in premixed spark ignition engine," Applied Energy, Elsevier, vol. 212(C), pages 210-222.
    7. Fiore, M. & Magi, V. & Viggiano, A., 2020. "Internal combustion engines powered by syngas: A review," Applied Energy, Elsevier, vol. 276(C).
    8. Jena, Priyaranjan & Raj, Reetu & Tirkey, Jeewan Vachan, 2023. "Thermodynamic performance study and RSM based optimization of SI engine using sewage sludge producer gas blend with methane," Energy, Elsevier, vol. 273(C).
    9. Carotenuto, Alberto & Di Fraia, Simona & Massarotti, Nicola & Sobek, Szymon & Uddin, M. Rakib & Vanoli, Laura & Werle, Sebastian, 2023. "Predictive modeling for energy recovery from sewage sludge gasification," Energy, Elsevier, vol. 263(PB).
    10. Raman, P. & Ram, N.K., 2013. "Performance analysis of an internal combustion engine operated on producer gas, in comparison with the performance of the natural gas and diesel engines," Energy, Elsevier, vol. 63(C), pages 317-333.
    11. Enomoto, Hiroshi & Saito, Kazuki, 2020. "Effects of the hydrogen and methane fractions in biosyngas on the stability of a small reciprocated internal combustion engine," Energy, Elsevier, vol. 213(C).
    12. Zhao, Jinxing, 2017. "Research and application of over-expansion cycle (Atkinson and Miller) engines – A review," Applied Energy, Elsevier, vol. 185(P1), pages 300-319.
    13. Jeong, Yong-Seong & Choi, Young-Kon & Park, Ki-Bum & Kim, Joo-Sik, 2019. "Air co-gasification of coal and dried sewage sludge in a two-stage gasifier: Effect of blending ratio on the producer gas composition and tar removal," Energy, Elsevier, vol. 185(C), pages 708-716.
    14. Nguyen, Dinh Duc & Moghaddam, Hesam & Pirouzfar, Vahid & Fayyazbakhsh, Ahmad & Su, Chia-Hung, 2021. "Improving the gasoline properties by blending butanol-Al2O3 to optimize the engine performance and reduce air pollution," Energy, Elsevier, vol. 218(C).
    15. Wang, Yi & He, Guanzhang & Huang, Haozhong & Guo, Xiaoyu & Xing, Kongzhao & Liu, Songtao & Tu, Zhanfei & Xia, Qi, 2023. "Thermodynamic and exergy analysis of high compression ratio coupled with late intake valve closing to improve thermal efficiency of two-stage turbocharged diesel engines," Energy, Elsevier, vol. 268(C).
    16. Ran, Zhongnan & Hariharan, Deivanayagam & Lawler, Benjamin & Mamalis, Sotirios, 2020. "Exploring the potential of ethanol, CNG, and syngas as fuels for lean spark-ignition combustion - An experimental study," Energy, Elsevier, vol. 191(C).
    17. Khatha Wathakit & Ekarong Sukjit & Chalita Kaewbuddee & Somkiat Maithomklang & Niti Klinkaew & Pansa Liplap & Weerachai Arjharn & Jiraphon Srisertpol, 2021. "Characterization and Impact of Waste Plastic Oil in a Variable Compression Ratio Diesel Engine," Energies, MDPI, vol. 14(8), pages 1-18, April.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Vargas-Salgado, Carlos & Águila-León, Jesús & Alfonso-Solar, David & Malmquist, Anders, 2022. "Simulations and experimental study to compare the behavior of a genset running on gasoline or syngas for small scale power generation," Energy, Elsevier, vol. 244(PA).
    2. Luigi De Simio & Sabato Iannaccone & Massimo Masi & Paolo Gobbato, 2022. "Experimental Study and Optimisation of a Non-Conventional Ignition System for Reciprocating Engines Operation with Hydrogen–Methane Blends, Syngas, and Biogas," Energies, MDPI, vol. 15(21), pages 1-21, November.
    3. Alberto Carotenuto & Simona Di Fraia & Nicola Massarotti & Szymon Sobek & M. Rakib Uddin & Laura Vanoli & Sebastian Werle, 2023. "Sewage Sludge Gasification Process Optimization for Combined Heat and Power Generation," Energies, MDPI, vol. 16(12), pages 1-22, June.
    4. Jeong, Yong-Seong & Kim, Jong-Woo & Seo, Myung-Won & Mun, Tae-Young & Kim, Joo-Sik, 2021. "Characteristics of two-stage air gasification of polystyrene with active carbon as a tar removal agent," Energy, Elsevier, vol. 219(C).
    5. Montazerinejad, H. & Eicker, U., 2022. "Recent development of heat and power generation using renewable fuels: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 165(C).
    6. Zhu, Sipeng & Liu, Sheng & Qu, Shuan & Deng, Kangyao, 2017. "Thermodynamic and experimental researches on matching strategies of the pre-turbine steam injection and the Miller cycle applied on a turbocharged diesel engine," Energy, Elsevier, vol. 140(P1), pages 488-505.
    7. Chehrmonavari, Hamed & Kakaee, Amirhasan & Hosseini, Seyed Ehsan & Desideri, Umberto & Tsatsaronis, George & Floerchinger, Gus & Braun, Robert & Paykani, Amin, 2023. "Hybridizing solid oxide fuel cells with internal combustion engines for power and propulsion systems: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 171(C).
    8. Quintero-Coronel, Daniel A. & Salazar, Adalberto & Pupo-Roncallo, Oscar R. & Bula, Antonio & Corredor, Lesme & Amador, German & Gonzalez-Quiroga, Arturo, 2023. "Assessment of the interchangeability of coal-biomass syngas with natural gas for atmospheric burners and high-pressure combustion applications," Energy, Elsevier, vol. 276(C).
    9. Raj, Reetu & Tirkey, Jeewan Vachan & Jena, Priyaranjan & Prajapati, Lawalesh Kumar, 2024. "Comparative analysis of Gasifier-CI engine performance and emissions characteristics using diesel with producer gas derived from coal– briquette-coconut shell-mahua feedstock and its blends," Energy, Elsevier, vol. 293(C).
    10. Jiang, Yankun & Chen, Yexin & Xie, Man, 2022. "Effects of blending dissociated methanol gas with the fuel in gasoline engine," Energy, Elsevier, vol. 247(C).
    11. Hoang, Anh Tuan, 2018. "Waste heat recovery from diesel engines based on Organic Rankine Cycle," Applied Energy, Elsevier, vol. 231(C), pages 138-166.
    12. Hiroshi Enomoto & Ryo Nakagawa, 2023. "Reduction in CO Emission from Small Reciprocating Engine Operated with Wood Gasifier by Mixture LHV Changing," Energies, MDPI, vol. 16(6), pages 1-14, March.
    13. Wang, Dan & Kuang, Minneng & Wang, Zhongshu & Su, Xing & Chen, Yiran & Jia, Demin, 2024. "Experimental study on the impact of Miller cycle coupled EGR on a natural gas engine," Energy, Elsevier, vol. 294(C).
    14. Fiore, M. & Magi, V. & Viggiano, A., 2020. "Internal combustion engines powered by syngas: A review," Applied Energy, Elsevier, vol. 276(C).
    15. Ram, Narasimhan Kodanda & Singh, Nameirakpam Rajesh & Raman, Perumal & Kumar, Atul & Kaushal, Priyanka, 2020. "Experimental study on performance analysis of an internal combustion engine operated on hydrogen-enriched producer gas from the air–steam gasification," Energy, Elsevier, vol. 205(C).
    16. Mohd Zeeshan & Rohan R. Pande & Purnanand V. Bhale, 2024. "A modeling study for the gasification of refuse-derived fuel as an alternative to waste disposal," Environment, Development and Sustainability: A Multidisciplinary Approach to the Theory and Practice of Sustainable Development, Springer, vol. 26(9), pages 23985-24008, September.
    17. Osorio, Julian D. & Rivera-Alvarez, Alejandro, 2018. "Efficiency enhancement of spark-ignition engines using a Continuous Variable Valve Timing system for load control," Energy, Elsevier, vol. 161(C), pages 649-662.
    18. Abu-Jrai, Ahmad M. & Al-Muhtaseb, Ala'a H. & Hasan, Ahmad O., 2017. "Combustion, performance, and selective catalytic reduction of NOx for a diesel engine operated with combined tri fuel (H2, CH4, and conventional diesel)," Energy, Elsevier, vol. 119(C), pages 901-910.
    19. Valeriy Nikitin & Elena Mikhalchenko & Lyuben Stamov & Nickolay Smirnov & Vilen Azatyan, 2023. "Mathematical Modeling of the Hydrodynamic Instability and Chemical Inhibition of Detonation Waves in a Syngas–Air Mixture," Mathematics, MDPI, vol. 11(24), pages 1-15, December.
    20. Santa Margarida Santos & Ana Carolina Assis & Leandro Gomes & Catarina Nobre & Paulo Brito, 2022. "Waste Gasification Technologies: A Brief Overview," Waste, MDPI, vol. 1(1), pages 1-26, December.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:289:y:2024:i:c:s036054422303462x. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.