IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v242y2022ics0360544221032461.html
   My bibliography  Save this article

Multi-objective optimization of DI diesel engine performance and emission parameters fueled with Jet-A1 – Diesel blends

Author

Listed:
  • Safieddin Ardebili, Seyed Mohammad
  • Babagiray, Mustafa
  • Aytav, Emre
  • Can, Özer
  • Boroiu, Andrei-Alexandru

Abstract

This study performed the performance and emission effects of adding Jet-A1 aviation fuel to diesel fuel in a direct injection, single-cylinder diesel engine. In addition, the response surface method was used to investigate combustion, performance, and emissions of the test fuel obtained by mixing Jet-A1 with diesel blends fuel under various engine conditions. Central Composite Design was used to create a design matrix. The input parameters were selected as brake torque and fuel type. On the other hand, the responses were selected as ignition delay time, specific fuel consumption, exhaust gas temperature, COVIMEP, CA50, CA10-90, CO, NOx, and soot emission. In order to determine the optimum operating range of the diesel engine, a desirability function was used. The optimum operating range of the diesel engine was found as brake torque of 11.25 Nm and Fuel Type of A25 by using the response surface method. Besides, response parameters were determined under optimum operating conditions as the specific fuel consumption of 0.257 kg/kWh, the ignition delay time of 1.296 ms, exhaust gas temperature of 367.53 °C, COVIMEP of 8.751%, CA50 of 14,984 °CA, CA10-90 of 95.319 °CA, CO of 264.06 ppm, soot emission of 0.715 (k factor (m-1)), and NOx of 132.279 ppm, respectively.

Suggested Citation

  • Safieddin Ardebili, Seyed Mohammad & Babagiray, Mustafa & Aytav, Emre & Can, Özer & Boroiu, Andrei-Alexandru, 2022. "Multi-objective optimization of DI diesel engine performance and emission parameters fueled with Jet-A1 – Diesel blends," Energy, Elsevier, vol. 242(C).
    • Handle: RePEc:eee:energy:v:242:y:2022:i:c:s0360544221032461
    DOI: 10.1016/j.energy.2021.122997
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544221032461
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2021.122997?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Solmaz, Hamit & Safieddin Ardebili, Seyed Mohammad & Aksoy, Fatih & Calam, Alper & Yılmaz, Emre & Arslan, Muhammed, 2020. "Optimization of the operating conditions of a beta-type rhombic drive stirling engine by using response surface method," Energy, Elsevier, vol. 198(C).
    2. Jack P. C. Kleijnen, 2015. "Response Surface Methodology," International Series in Operations Research & Management Science, in: Michael C Fu (ed.), Handbook of Simulation Optimization, edition 127, chapter 0, pages 81-104, Springer.
    3. El-Zoheiry, Radwan M. & EL-Seesy, Ahmed I. & Attia, Ali M.A. & He, Zhixia & El-Batsh, Hesham M., 2020. "Combustion and emission characteristics of Jojoba biodiesel-jet A1 mixtures applying a lean premixed pre-vaporized combustion techniques: An experimental investigation," Renewable Energy, Elsevier, vol. 162(C), pages 2227-2245.
    4. Calam, Alper & Solmaz, Hamit & Yılmaz, Emre & İçingür, Yakup, 2019. "Investigation of effect of compression ratio on combustion and exhaust emissions in A HCCI engine," Energy, Elsevier, vol. 168(C), pages 1208-1216.
    5. Maohua Xiao & Xiaojie Shen & You Ma & Fei Yang & Nong Gao & Weihua Wei & Dan Wu, 2018. "Prediction of Surface Roughness and Optimization of Cutting Parameters of Stainless Steel Turning Based on RSM," Mathematical Problems in Engineering, Hindawi, vol. 2018, pages 1-15, August.
    6. Abuhabaya, Abdullah & Fieldhouse, John & Brown, David, 2013. "The effects of using biodiesel on CI (compression ignition) engine and optimization of its production by using response surface methodology," Energy, Elsevier, vol. 59(C), pages 56-62.
    7. Najafi, Gholamhassan & Ghobadian, Barat & Yusaf, Talal & Safieddin Ardebili, Seyed Mohammad & Mamat, Rizalman, 2015. "Optimization of performance and exhaust emission parameters of a SI (spark ignition) engine with gasoline–ethanol blended fuels using response surface methodology," Energy, Elsevier, vol. 90(P2), pages 1815-1829.
    8. Chuck, Christopher J. & Donnelly, Joseph, 2014. "The compatibility of potential bioderived fuels with Jet A-1 aviation kerosene," Applied Energy, Elsevier, vol. 118(C), pages 83-91.
    9. Gabriel Talero & Camilo Bayona-Roa & Giovanny Muñoz & Miguel Galindo & Vladimir Silva & Juan Pava & Mauricio Lopez, 2019. "Experimental Methodology and Facility for the J69-Engine Performance and Emissions Evaluation Using Jet A1 and Biodiesel Blends," Energies, MDPI, vol. 12(23), pages 1-10, November.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Çelebi, Samet & Kocakulak, Tolga & Demir, Usame & Ergen, Gökhan & Yilmaz, Emre, 2023. "Optimizing the effect of a mixture of light naphtha, diesel and gasoline fuels on engine performance and emission values on an HCCI engine," Applied Energy, Elsevier, vol. 330(PB).
    2. Babagiray, Mustafa & Kocakulak, Tolga & Safieddin Ardebili, Seyed Mohammad & Solmaz, Hamit & Çınar, Can & Uyumaz, Ahmet, 2022. "Experimental and statistical investigation of different valve lifts on HCCI combustion, performance and exhaust emissions using response surface method," Energy, Elsevier, vol. 244(PB).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Solmaz, Hamit & Safieddin Ardebili, Seyed Mohammad & Aksoy, Fatih & Calam, Alper & Yılmaz, Emre & Arslan, Muhammed, 2020. "Optimization of the operating conditions of a beta-type rhombic drive stirling engine by using response surface method," Energy, Elsevier, vol. 198(C).
    2. Renzi, Massimiliano & Bietresato, Marco & Mazzetto, Fabrizio, 2016. "An experimental evaluation of the performance of a SI internal combustion engine for agricultural purposes fuelled with different bioethanol blends," Energy, Elsevier, vol. 115(P1), pages 1069-1080.
    3. Najafi, Gholamhassan & Ghobadian, Barat & Yusaf, Talal & Safieddin Ardebili, Seyed Mohammad & Mamat, Rizalman, 2015. "Optimization of performance and exhaust emission parameters of a SI (spark ignition) engine with gasoline–ethanol blended fuels using response surface methodology," Energy, Elsevier, vol. 90(P2), pages 1815-1829.
    4. Al-Harbi, Ahmed A. & Alabduly, Abdullah J. & Alkhedhair, Abdullah M. & Alqahtani, Naif B. & Albishi, Miqad S., 2022. "Effect of operation under lean conditions on NOx emissions and fuel consumption fueling an SI engine with hydrous ethanol–gasoline blends enhanced with synthesis gas," Energy, Elsevier, vol. 238(PA).
    5. Kocakulak, Tolga & Babagiray, Mustafa & Nacak, Çağatay & Safieddin Ardebili, Seyed Mohammad & Calam, Alper & Solmaz, Hamit, 2022. "Multi objective optimization of HCCI combustion fuelled with fusel oil and n-heptane blends," Renewable Energy, Elsevier, vol. 182(C), pages 827-841.
    6. Thakur, Amit Kumar & Kaviti, Ajay Kumar & Mehra, Roopesh & Mer, K.K.S., 2017. "Progress in performance analysis of ethanol-gasoline blends on SI engine," Renewable and Sustainable Energy Reviews, Elsevier, vol. 69(C), pages 324-340.
    7. Prasad, G. Arun & Murugan, P.C. & Wincy, W. Beno & Sekhar, S. Joseph, 2021. "Response Surface Methodology to predict the performance and emission characteristics of gas-diesel engine working on producer gases of non-uniform calorific values," Energy, Elsevier, vol. 234(C).
    8. Amir Hossein Arkian & Gholamhassan Najafi & Shiva Gorjian & Reyhaneh Loni & Evangelos Bellos & Talal Yusaf, 2019. "Performance Assessment of a Solar Dryer System Using Small Parabolic Dish and Alumina/Oil Nanofluid: Simulation and Experimental Study," Energies, MDPI, vol. 12(24), pages 1-22, December.
    9. Yaman, Hayri & Yesilyurt, Murat Kadir & Uslu, Samet, 2022. "Simultaneous optimization of multiple engine parameters of a 1-heptanol / gasoline fuel blends operated a port-fuel injection spark-ignition engine using response surface methodology approach," Energy, Elsevier, vol. 238(PC).
    10. Solmaz, Hamit & Ardebili, Seyed Mohammad Safieddin & Calam, Alper & Yılmaz, Emre & İpci, Duygu, 2021. "Prediction of performance and exhaust emissions of a CI engine fueled with multi-wall carbon nanotube doped biodiesel-diesel blends using response surface method," Energy, Elsevier, vol. 227(C).
    11. Krishnamoorthi, M. & Malayalamurthi, R. & Sakthivel, R., 2019. "Optimization of compression ignition engine fueled with diesel - chaulmoogra oil - diethyl ether blend with engine parameters and exhaust gas recirculation," Renewable Energy, Elsevier, vol. 134(C), pages 579-602.
    12. Alberth Renne Gonzalez Caranton & Vladimir Silva Leal & Camilo Bayona-Roa & Manuel Alejandro Mayorga Betancourt & Carolina Betancourt & Deiver Cortina & Nelson Jimenez Acuña & Mauricio López, 2021. "Experimental Investigation of the Mechanical and Thermal Behavior of a PT6A-61A Engine Using Mixtures of JETA-1 and Biodiesel," Energies, MDPI, vol. 14(11), pages 1-22, June.
    13. Juan E. Tibaquirá & José I. Huertas & Sebastián Ospina & Luis F. Quirama & José E. Niño, 2018. "The Effect of Using Ethanol-Gasoline Blends on the Mechanical, Energy and Environmental Performance of In-Use Vehicles," Energies, MDPI, vol. 11(1), pages 1-17, January.
    14. Shen-Tsu Wang, 2016. "Integrating grey sequencing with the genetic algorithm--immune algorithm to optimise touch panel cover glass polishing process parameter design," International Journal of Production Research, Taylor & Francis Journals, vol. 54(16), pages 4882-4893, August.
    15. Kale, Aneesh Vijay & Krishnasamy, Anand, 2023. "Experimental study of homogeneous charge compression ignition combustion in a light-duty diesel engine fueled with isopropanol–gasoline blends," Energy, Elsevier, vol. 264(C).
    16. Atsonios, Konstantinos & Kougioumtzis, Michael-Alexander & D. Panopoulos, Kyriakos & Kakaras, Emmanuel, 2015. "Alternative thermochemical routes for aviation biofuels via alcohols synthesis: Process modeling, techno-economic assessment and comparison," Applied Energy, Elsevier, vol. 138(C), pages 346-366.
    17. Yek, Peter Nai Yuh & Cheng, Yoke Wang & Liew, Rock Keey & Wan Mahari, Wan Adibah & Ong, Hwai Chyuan & Chen, Wei-Hsin & Peng, Wanxi & Park, Young-Kwon & Sonne, Christian & Kong, Sieng Huat & Tabatabaei, 2021. "Progress in the torrefaction technology for upgrading oil palm wastes to energy-dense biochar: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 151(C).
    18. Qin, Caiyan & Kim, Joong Bae & Lee, Bong Jae, 2019. "Performance analysis of a direct-absorption parabolic-trough solar collector using plasmonic nanofluids," Renewable Energy, Elsevier, vol. 143(C), pages 24-33.
    19. Belal, Belal Y. & Li, Gesheng & Zhang, Zunhua & El-Batsh, H.M. & Moneib, Hany A. & Attia, Ali M.A., 2021. "The effect of swirl burner design configuration on combustion and emission characteristics of lean pre-vaporized premixed flames," Energy, Elsevier, vol. 228(C).
    20. K. M. V. Ravi Teja & P. Issac Prasad & K. Vijaya Kumar Reddy & N. R. Banapurmath & Manzoore Elahi M. Soudagar & T. M. Yunus Khan & Irfan Anjum Badruddin, 2021. "Influence of Combustion Chamber Shapes and Nozzle Geometry on Performance, Emission, and Combustion Characteristics of CRDI Engine Powered with Biodiesel Blends," Sustainability, MDPI, vol. 13(17), pages 1-19, August.

    More about this item

    Keywords

    Diesel engine; Response surface method; Jet A1 aviation fuel; Combustion;
    All these keywords.

    JEL classification:

    • A1 - General Economics and Teaching - - General Economics

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:242:y:2022:i:c:s0360544221032461. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.