IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v228y2021ics0360544221008331.html
   My bibliography  Save this article

Outstanding performance of direct urea/hydrogen peroxide fuel cell based on precious metal-free catalyst electrodes

Author

Listed:
  • Eisa, Tasnim
  • Park, Sung-Gwan
  • Mohamed, Hend Omar
  • Abdelkareem, Mohammad Ali
  • Lee, Jieun
  • Yang, Euntae
  • Castaño, Pedro
  • Chae, Kyu-Jung

Abstract

Direct urea/hydrogen peroxide fuel cells (DUHP-FCs) can produce electrical energy by recycling urea-rich wastewater. This study expands the commerciality of DUHP-FC by removing precious metals from their design. Nickel nanorod/nickel foam (NNR/NF) was fabricated using hydrothermal treatment to be used as the anode, and Prussian blue coating was deposited by potentiostatic electrodeposition onto hydrophilic carbon felt at the cathode (PB/CF). The anode exhibited a 7-folds higher current density than bare NF at 0–2 M urea, and lower charge transfer resistance. The cathode reported a high H2O2 reduction current. In addition, fuel cell tests indicated current density dependency on H2O2 concentration and cell voltage dependency on KCl concentration. A competitive maximum power density of 10.6 mW cm−2 was achieved at 0.98 open circuit voltage and 45 mA cm−2 maximum current density, in 0.33 M urea vs 2 M KCl and 2 M H2O2, exclusively via diffusive mass transfer. These findings indicate the practical application of DUHP-FC on a large scale.

Suggested Citation

  • Eisa, Tasnim & Park, Sung-Gwan & Mohamed, Hend Omar & Abdelkareem, Mohammad Ali & Lee, Jieun & Yang, Euntae & Castaño, Pedro & Chae, Kyu-Jung, 2021. "Outstanding performance of direct urea/hydrogen peroxide fuel cell based on precious metal-free catalyst electrodes," Energy, Elsevier, vol. 228(C).
    • Handle: RePEc:eee:energy:v:228:y:2021:i:c:s0360544221008331
    DOI: 10.1016/j.energy.2021.120584
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544221008331
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2021.120584?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Diaz-Mendez, S.E. & Sierra-Grajeda, J.M.T. & Hernandez-Guerrero, A. & Rodriguez-Lelis, J.M., 2013. "Entropy generation as an environmental impact indicator and a sample application to freshwater ecosystems eutrophication," Energy, Elsevier, vol. 61(C), pages 234-239.
    2. Alami, Abdul Hai & Abdelkareem, Mohammad Ali & Faraj, Mohammed & Aokal, Kamilia & Al Safarini, Nada, 2020. "Titanium dioxide-coated nickel foam photoelectrodes for direct urea fuel cell applications," Energy, Elsevier, vol. 208(C).
    3. Zinadini, S. & Zinatizadeh, A.A. & Rahimi, M. & Vatanpour, V. & Rahimi, Z., 2017. "High power generation and COD removal in a microbial fuel cell operated by a novel sulfonated PES/PES blend proton exchange membrane," Energy, Elsevier, vol. 125(C), pages 427-438.
    4. Yang, Chii-Rong & Lu, Chang-Wei & Fu, Pin-Chi & Cheng, Chia & Chiou, Yuang-Cherng & Lee, Rong-Tsong & Tseng, Shih-Feng, 2020. "Performance evaluation of μDMFCs based on porous-silicon electrodes and methanol modification," Energy, Elsevier, vol. 192(C).
    5. Braz, B.A. & Oliveira, V.B. & Pinto, A.M.F.R., 2020. "Optimization of a passive direct methanol fuel cell with different current collector materials," Energy, Elsevier, vol. 208(C).
    6. Mohammed, Hanin & Al-Othman, Amani & Nancarrow, Paul & Tawalbeh, Muhammad & El Haj Assad, Mamdouh, 2019. "Direct hydrocarbon fuel cells: A promising technology for improving energy efficiency," Energy, Elsevier, vol. 172(C), pages 207-219.
    7. Song, Xingjuan & Zhang, Dongming, 2014. "Bimetallic Ag–Ni/C particles as cathode catalyst in AFCs (alkaline fuel cells)," Energy, Elsevier, vol. 70(C), pages 223-230.
    8. Siegel, C., 2008. "Review of computational heat and mass transfer modeling in polymer-electrolyte-membrane (PEM) fuel cells," Energy, Elsevier, vol. 33(9), pages 1331-1352.
    9. Silveira, Gustavo & de Aquino Neto, Sidney & Schneedorf, José Maurício, 2020. "Development, characterization and application of a low-cost single chamber microbial fuel cell based on hydraulic couplers," Energy, Elsevier, vol. 208(C).
    10. Olabi, A.G. & Wilberforce, Tabbi & Abdelkareem, Mohammad Ali, 2021. "Fuel cell application in the automotive industry and future perspective," Energy, Elsevier, vol. 214(C).
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Sayed, Enas Taha & Abdelkareem, Mohammad Ali & Bahaa, Ahmed & Eisa, Tasnim & Alawadhi, Hussain & Al-Asheh, Sameer & Chae, Kyu-Jung & Olabi, A.G., 2021. "Synthesis and performance evaluation of various metal chalcogenides as active anodes for direct urea fuel cells," Renewable and Sustainable Energy Reviews, Elsevier, vol. 150(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Maria H. de Sá & Alexandra M. F. R. Pinto & Vânia B. Oliveira, 2022. "Passive Small Direct Alcohol Fuel Cells for Low-Power Portable Applications: Assessment Based on Innovative Increments since 2018," Energies, MDPI, vol. 15(10), pages 1-48, May.
    2. Ong, Samuel & Al-Othman, Amani & Tawalbeh, Muhammad, 2023. "Emerging technologies in prognostics for fuel cells including direct hydrocarbon fuel cells," Energy, Elsevier, vol. 277(C).
    3. Mohamed, Hend Omar & Talas, Sawsan Abo & Sayed, Enas T. & Park, Sung-Gwan & Eisa, Tasnim & Abdelkareem, Mohammad Ali & Fadali, Olfat A. & Chae, Kyu-Jung & Castaño, Pedro, 2021. "Enhancing power generation in microbial fuel cell using tungsten carbide on reduced graphene oxide as an efficient anode catalyst material," Energy, Elsevier, vol. 229(C).
    4. A. G. Olabi & Tabbi Wilberforce & Khaled Elsaid & Tareq Salameh & Enas Taha Sayed & Khaled Saleh Husain & Mohammad Ali Abdelkareem, 2021. "Selection Guidelines for Wind Energy Technologies," Energies, MDPI, vol. 14(11), pages 1-34, June.
    5. Zhang, Xiaoqing & Yang, Jiapei & Ma, Xiao & Zhuge, Weilin & Shuai, Shijin, 2022. "Modelling and analysis on effects of penetration of microporous layer into gas diffusion layer in PEM fuel cells: Focusing on mass transport," Energy, Elsevier, vol. 254(PA).
    6. Zheng Huang & Laisuo Su & Yunjie Yang & Linsong Gao & Xinyu Liu & Heng Huang & Yubai Li & Yongchen Song, 2023. "Three-Dimensional Simulation on the Effects of Different Parameters and Pt Loading on the Long-Term Performance of Proton Exchange Membrane Fuel Cells," Sustainability, MDPI, vol. 15(4), pages 1-22, February.
    7. Jang, Jiin-Yuh & Cheng, Chin-Hsiang & Liao, Wang-Ting & Huang, Yu-Xian & Tsai, Ying-Chi, 2012. "Experimental and numerical study of proton exchange membrane fuel cell with spiral flow channels," Applied Energy, Elsevier, vol. 99(C), pages 67-79.
    8. Barzegari, Mohammad M. & Dardel, Morteza & Alizadeh, Ebrahim & Ramiar, Abas, 2016. "Dynamic modeling and validation studies of dead-end cascade H2/O2 PEM fuel cell stack with integrated humidifier and separator," Applied Energy, Elsevier, vol. 177(C), pages 298-308.
    9. Salva, J. Antonio & Iranzo, Alfredo & Rosa, Felipe & Tapia, Elvira, 2016. "Validation of cell voltage and water content in a PEM (polymer electrolyte membrane) fuel cell model using neutron imaging for different operating conditions," Energy, Elsevier, vol. 101(C), pages 100-112.
    10. Abdollahzadeh, M. & Ribeirinha, P. & Boaventura, M. & Mendes, A., 2018. "Three-dimensional modeling of PEMFC with contaminated anode fuel," Energy, Elsevier, vol. 152(C), pages 939-959.
    11. Najmi, Aezid-Ul-Hassan & Anyanwu, Ikechukwu S. & Xie, Xu & Liu, Zhi & Jiao, Kui, 2021. "Experimental investigation and optimization of proton exchange membrane fuel cell using different flow fields," Energy, Elsevier, vol. 217(C).
    12. Ahmed M. Nassef & Ahmed Handam, 2022. "Parameter Estimation-Based Slime Mold Algorithm of Photocatalytic Methane Reforming Process for Hydrogen Production," Sustainability, MDPI, vol. 14(5), pages 1-12, March.
    13. K. Arunprasath & S. Bathrinath & R. K. A. Bhalaji & Koppiahraj Karuppiah & Anish Nair, 2023. "An integrated approach to modelling of barriers in implementation of cellular manufacturing systems in production industries," International Journal of System Assurance Engineering and Management, Springer;The Society for Reliability, Engineering Quality and Operations Management (SREQOM),India, and Division of Operation and Maintenance, Lulea University of Technology, Sweden, vol. 14(4), pages 1370-1378, August.
    14. Belessiotis, George V. & Kontos, Athanassios G., 2022. "Plasmonic silver (Ag)-based photocatalysts for H2 production and CO2 conversion: Review, analysis and perspectives," Renewable Energy, Elsevier, vol. 195(C), pages 497-515.
    15. Venkatesan, Suriya & Mitzel, Jens & Wegner, Karsten & Costa, Remi & Gazdzicki, Pawel & Friedrich, Kaspar Andreas, 2022. "Nanomaterials and films for polymer electrolyte membrane fuel cells and solid oxide cells by flame spray pyrolysis," Renewable and Sustainable Energy Reviews, Elsevier, vol. 158(C).
    16. Wang, Chenfang & Li, Qingshan & Wang, Chunmei & Zhang, Yangjun & Zhuge, Weilin, 2021. "Thermodynamic analysis of a hydrogen fuel cell waste heat recovery system based on a zeotropic organic Rankine cycle," Energy, Elsevier, vol. 232(C).
    17. Chang, Huawei & Cai, Fengyang & Yu, Xianxian & Duan, Chen & Chan, Siew Hwa & Tu, Zhengkai, 2023. "Experimental study on the thermal management of an open-cathode air-cooled proton exchange membrane fuel cell stack with ultra-thin metal bipolar plates," Energy, Elsevier, vol. 263(PA).
    18. Fofana, Daouda & Natarajan, Sadesh Kumar & Hamelin, Jean & Benard, Pierre, 2014. "Low platinum, high limiting current density of the PEMFC (proton exchange membrane fuel cell) based on multilayer cathode catalyst approach," Energy, Elsevier, vol. 64(C), pages 398-403.
    19. Jung, Chi-Young & Yi, Jae-You & Yi, Sung-Chul, 2014. "On the role of the silica-containing catalyst layer for proton exchange membrane fuel cells," Energy, Elsevier, vol. 68(C), pages 794-800.
    20. Ismail, M.S. & Ingham, D.B. & Ma, L. & Hughes, K.J. & Pourkashanian, M., 2017. "Effects of catalyst agglomerate shape in polymer electrolyte fuel cells investigated by a multi-scale modelling framework," Energy, Elsevier, vol. 122(C), pages 420-430.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:228:y:2021:i:c:s0360544221008331. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.