IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v209y2020ics0360544220315280.html
   My bibliography  Save this article

Experimental and numerical study on the flame characteristics and cooling effectiveness of air-cooled flame holder

Author

Listed:
  • Shilong, Zhao
  • Yuxin, Fan

Abstract

For high-performance combustion, it needs to meet the requirements of flame stability and heat protection at a wide operating range. In this work, a novel air-cooled flame holding device containing impingement holes and faced film holes, which can achieve flame stabilization and reduce wall temperature. The cooling air flows out and forms vortices attaching on the back wall, functioning as a thickened film that reduces heat transfer and control the distance between the flame and the back wall. The novel composite cooling scheme worked effectively at reaction state and achieved an almost 20% reduction of wall temperature, and the cooling effect of the 30-deg faced film hole was much better than that of the 60-deg faced film hole. Flame stabilization was influenced by the increasing mass rate of cooling air. The oversize distance of flame stabilizing zone and back wall easily caused flame instability even blow-off. 0.3% and 0.5% mass rate of cooling air were enough to achieve flame stabilization and work effectively to decrease wall temperature. The novel air-cooled flame holder saw both flame stability and cooling effectiveness. Because of its compact design and resistance to thermal ablation, it can be of great importance for an advanced burner.

Suggested Citation

  • Shilong, Zhao & Yuxin, Fan, 2020. "Experimental and numerical study on the flame characteristics and cooling effectiveness of air-cooled flame holder," Energy, Elsevier, vol. 209(C).
  • Handle: RePEc:eee:energy:v:209:y:2020:i:c:s0360544220315280
    DOI: 10.1016/j.energy.2020.118421
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544220315280
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.energy.2020.118421?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Zhang, R.C. & Bai, N.J. & Fan, W.J. & Yan, W.H. & Hao, F. & Yin, C.M., 2018. "Flow field and combustion characteristics of integrated combustion mode using cavity with low flow resistance for gas turbine engines," Energy, Elsevier, vol. 165(PA), pages 979-996.
    2. Song, Jiwoon & Lee, Keon Woo & Kim, Kyung Min & Cho, Hyung Hee, 2012. "Slot film cooling performance in combustor with flame holders," Energy, Elsevier, vol. 37(1), pages 533-539.
    3. Kim, Kyung Min & Kim, Beom Seok & Lee, Dong Hyun & Moon, Hokyu & Cho, Hyung Hee, 2010. "Optimal design of transverse ribs in tubes for thermal performance enhancement," Energy, Elsevier, vol. 35(6), pages 2400-2406.
    4. Lee, Dong Hyun & Rhee, Dong-Ho & Kim, Kyung Min & Cho, Hyung Hee & Moon, Hee Koo, 2009. "Detailed measurement of heat/mass transfer with continuous and multiple V-shaped ribs in rectangular channel," Energy, Elsevier, vol. 34(11), pages 1770-1778.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Chen, Yuqian & Fan, Yuxin & Han, Qixiang, 2022. "Experimental investigation of thermal protection performance of bluff-body flameholder in augmented combustor under air jet cooling," Energy, Elsevier, vol. 254(PB).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Hwang, Sang Dong & Kwon, Hyun Goo & Cho, Hyung Hee, 2010. "Local heat transfer and thermal performance on periodically dimple-protrusion patterned walls for compact heat exchangers," Energy, Elsevier, vol. 35(12), pages 5357-5364.
    2. Song, Jiwoon & Lee, Keon Woo & Kim, Kyung Min & Cho, Hyung Hee, 2012. "Slot film cooling performance in combustor with flame holders," Energy, Elsevier, vol. 37(1), pages 533-539.
    3. Park, Jun Su & Park, Sehjin & Kim, Kyung Min & Choi, Beom Seok & Cho, Hyung Hee, 2013. "Effect of the thermal insulation on generator and micro gas turbine system," Energy, Elsevier, vol. 59(C), pages 581-589.
    4. Kim, Kyung Min & Jeon, Yun Heung & Yun, Namgeon & Lee, Dong Hyun & Cho, Hyung Hee, 2011. "Thermo-mechanical life prediction for material lifetime improvement of an internal cooling system in a combustion liner," Energy, Elsevier, vol. 36(2), pages 942-949.
    5. Jin, Dongxu & Zhang, Manman & Wang, Ping & Xu, Shasha, 2015. "Numerical investigation of heat transfer and fluid flow in a solar air heater duct with multi V-shaped ribs on the absorber plate," Energy, Elsevier, vol. 89(C), pages 178-190.
    6. Nidhul, Kottayat & Kumar, Sachin & Yadav, Ajay Kumar & Anish, S., 2020. "Enhanced thermo-hydraulic performance in a V-ribbed triangular duct solar air heater: CFD and exergy analysis," Energy, Elsevier, vol. 200(C).
    7. Shilong, Zhao & Yuxin, Fan & Deng, Tiantai & Crookes, Danny, 2020. "Influence of injection scheme on flame characteristics in partially premixed combustion," Energy, Elsevier, vol. 205(C).
    8. Joo, Seongpil & Choi, Jongwun & Lee, Min Chul & Kim, Namkeun, 2021. "Prognosis of combustion instability in a gas turbine combustor using spectral centroid & spread," Energy, Elsevier, vol. 224(C).
    9. Jin, Dongxu & Zuo, Jianguo & Quan, Shenglin & Xu, Shiming & Gao, Hao, 2017. "Thermohydraulic performance of solar air heater with staggered multiple V-shaped ribs on the absorber plate," Energy, Elsevier, vol. 127(C), pages 68-77.
    10. Zhang, R.C. & Bai, N.J. & Fan, W.J. & Huang, X.Y. & Fan, X.Q., 2019. "Influence of flame stabilization and fuel injection modes on the flow and combustion characteristics of gas turbine combustor with cavity," Energy, Elsevier, vol. 189(C).
    11. Xiangzhong Jia & Yong Shan & Xingping Xu & Jingzhou Zhang & Xiaoming Tan, 2021. "Effects of Bypass Flow Distribution on Cold Flow Characteristics of Integrated Afterburner," Energies, MDPI, vol. 14(18), pages 1-17, September.
    12. Kim, Kyung Min & Moon, Hokyu & Park, Jun Su & Cho, Hyung Hee, 2014. "Optimal design of impinging jets in an impingement/effusion cooling system," Energy, Elsevier, vol. 66(C), pages 839-848.
    13. Kim, Kyung Min & Kim, Beom Seok & Lee, Dong Hyun & Moon, Hokyu & Cho, Hyung Hee, 2010. "Optimal design of transverse ribs in tubes for thermal performance enhancement," Energy, Elsevier, vol. 35(6), pages 2400-2406.
    14. Kuan-Tzu Huang & Yao-Hsien Liu, 2019. "Enhancement of Mist Flow Cooling by Using V-Shaped Broken Ribs," Energies, MDPI, vol. 12(19), pages 1-18, October.
    15. Alam, Tabish & Saini, R.P. & Saini, J.S., 2014. "Use of turbulators for heat transfer augmentation in an air duct – A review," Renewable Energy, Elsevier, vol. 62(C), pages 689-715.
    16. Chamoli, Sunil & Thakur, N.S. & Saini, J.S., 2012. "A review of turbulence promoters used in solar thermal systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(5), pages 3154-3175.
    17. Bhushan, Brij & Singh, Ranjit, 2010. "A review on methodology of artificial roughness used in duct of solar air heaters," Energy, Elsevier, vol. 35(1), pages 202-212.
    18. Shilong, Zhao & Yuxin, Fan, 2020. "Experimental and numerical study on fuel distribution and flame expansion of the enhanced flame holding devices," Energy, Elsevier, vol. 203(C).
    19. Wei-Jie Su & Yao-Hsien Liu, 2021. "Thermal Performance of V-Shaped and X-Shaped Ribs in Trapezoidal Cooling Channels," Energies, MDPI, vol. 14(16), pages 1-15, August.
    20. Zhang, Fan & Liu, Cunliang & Ye, Lin & Ran, Yuan & Zhou, Tianliang & Yan, Haonan, 2024. "Study on the film superposition method for dense multirow film Hole layouts," Energy, Elsevier, vol. 293(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:209:y:2020:i:c:s0360544220315280. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.