IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v357y2024ics0306261923018706.html
   My bibliography  Save this article

Modelling, simulation, and optimisation of a novel liquid piston system for energy recovery

Author

Listed:
  • Aliaga, D.M.
  • Romero, C.P.
  • Feick, R.
  • Brooks, W.K.
  • Campbell, A.N.

Abstract

A simple, scalable, and efficient method is proposed to extract energy from a pressurised gas flow to generate electrical power. The proposed liquid piston system is fed continuously with air into the piston chamber, which is filled with water. The water is driven by the gas’s expansion, and their interaction enables an isothermal expansion. A dynamic model was developed in gPROMS and validated against 300 W and 4 kW experimental data. The accuracy of the power output predictions has a maximum discrepancy of less than 6.4% from the experimental values. Subsequently, a sensitivity analysis and optimisation using the height to diameter piston geometry ratio was performed to study the variation in the thermal efficiency. The simulations were performed for energy systems from 300 kW to 100 MW and for several intake gas temperatures. The study shows that lower piston geometry ratios of 4 are preferred for 300 kW and 1 MW case studies. Because of reduced heat transfer between water and air, these systems reach 92.5% thermal efficiency. Moreover, the predicted thermal efficiencies for high power ratings were as high as 82%. The power output values obtained were constant in time. Finally, an energy and exergy assessment and worst-case scenario with decreased turbo machinery efficiency are presented. The proposed method matches the specific power of traditional power cycles and has potential uses for energy recovery in cryogenic plants.

Suggested Citation

  • Aliaga, D.M. & Romero, C.P. & Feick, R. & Brooks, W.K. & Campbell, A.N., 2024. "Modelling, simulation, and optimisation of a novel liquid piston system for energy recovery," Applied Energy, Elsevier, vol. 357(C).
  • Handle: RePEc:eee:appene:v:357:y:2024:i:c:s0306261923018706
    DOI: 10.1016/j.apenergy.2023.122506
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261923018706
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.apenergy.2023.122506?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Stecco, Sergio S. & Manfrida, Giampaolo, 1986. "Exergy analysis of compression and expansion processes," Energy, Elsevier, vol. 11(6), pages 573-577.
    2. Odukomaiya, Adewale & Abu-Heiba, Ahmad & Gluesenkamp, Kyle R. & Abdelaziz, Omar & Jackson, Roderick K. & Daniel, Claus & Graham, Samuel & Momen, Ayyoub M., 2016. "Thermal analysis of near-isothermal compressed gas energy storage system," Applied Energy, Elsevier, vol. 179(C), pages 948-960.
    3. Vallati, A. & de Lieto Vollaro, R. & Oclon, P. & Taler, J., 2021. "Experimental and analytical evaluation of a gas-liquid energy storage (GLES) prototype," Energy, Elsevier, vol. 224(C).
    4. Jokar, H. & Tavakolpour-Saleh, A.R., 2015. "A novel solar-powered active low temperature differential Stirling pump," Renewable Energy, Elsevier, vol. 81(C), pages 319-337.
    5. Odukomaiya, Adewale & Abu-Heiba, Ahmad & Graham, Samuel & Momen, Ayyoub M., 2018. "Experimental and analytical evaluation of a hydro-pneumatic compressed-air Ground-Level Integrated Diverse Energy Storage (GLIDES) system," Applied Energy, Elsevier, vol. 221(C), pages 75-85.
    6. Gouda, El Mehdi & Neu, Thibault & Benaouicha, Mustapha & Fan, Yilin & Subrenat, Albert & Luo, Lingai, 2023. "Experimental and numerical investigation on the flow and heat transfer behaviors during a compression–cooling–expansion cycle using a liquid piston for compressed air energy storage," Energy, Elsevier, vol. 277(C).
    7. Argyrou, Maria C. & Christodoulides, Paul & Kalogirou, Soteris A., 2018. "Energy storage for electricity generation and related processes: Technologies appraisal and grid scale applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 94(C), pages 804-821.
    8. Li, Chengchen & Wang, Huanran & He, Xin & Zhang, Yan, 2022. "Experimental and thermodynamic investigation on isothermal performance of large-scaled liquid piston," Energy, Elsevier, vol. 249(C).
    9. Klüppel, Rogerio P. & Gurgel, JoséMaurício M., 1998. "Thermodynamic cycle of a liquid piston pump," Renewable Energy, Elsevier, vol. 13(2), pages 261-268.
    10. Huanran Wang & Liqin Wang & Xinbing Wang & Erren Yao, 2013. "A Novel Pumped Hydro Combined with Compressed Air Energy Storage System," Energies, MDPI, vol. 6(3), pages 1-14, March.
    11. Bi, Xianyun & Liu, Pei & Li, Zheng, 2016. "Thermo-dynamic analysis and simulation of a combined air and hydro energy storage (CAHES) system," Energy, Elsevier, vol. 116(P2), pages 1385-1396.
    12. Van de Ven, James D. & Li, Perry Y., 2009. "Liquid piston gas compression," Applied Energy, Elsevier, vol. 86(10), pages 2183-2191, October.
    13. Igobo, Opubo N. & Davies, Philip A., 2014. "Review of low-temperature vapour power cycle engines with quasi-isothermal expansion," Energy, Elsevier, vol. 70(C), pages 22-34.
    14. Chen, Hao & Wang, Huanran & Li, Ruixiong & Sun, Hao & Ge, Gangqiang & Ling, Lanning, 2022. "Experimental and analytical investigation of near-isothermal pumped hydro-compressed air energy storage system," Energy, Elsevier, vol. 249(C).
    15. Gouda, El Mehdi & Benaouicha, Mustapha & Neu, Thibault & Fan, Yilin & Luo, Lingai, 2022. "Flow and heat transfer characteristics of air compression in a liquid piston for compressed air energy storage," Energy, Elsevier, vol. 254(PB).
    16. Hadjipaschalis, Ioannis & Poullikkas, Andreas & Efthimiou, Venizelos, 2009. "Overview of current and future energy storage technologies for electric power applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 13(6-7), pages 1513-1522, August.
    17. Camargos, Tomás P.L. & Pottie, Daniel L.F. & Ferreira, Rafael A.M. & Maia, Thales A.C. & Porto, Matheus P., 2018. "Experimental study of a PH-CAES system: Proof of concept," Energy, Elsevier, vol. 165(PA), pages 630-638.
    18. Erren Yao & Huanran Wang & Long Liu & Guang Xi, 2014. "A Novel Constant-Pressure Pumped Hydro Combined with Compressed Air Energy Storage System," Energies, MDPI, vol. 8(1), pages 1-18, December.
    19. Pottie, Daniel L.F. & Ferreira, Rafael A.M. & Maia, Thales A.C. & Porto, Matheus P., 2020. "An alternative sequence of operation for Pumped-Hydro Compressed Air Energy Storage (PH-CAES) systems," Energy, Elsevier, vol. 191(C).
    20. Yan, Bo & Wieberdink, Jacob & Shirazi, Farzad & Li, Perry Y. & Simon, Terrence W. & Van de Ven, James D., 2015. "Experimental study of heat transfer enhancement in a liquid piston compressor/expander using porous media inserts," Applied Energy, Elsevier, vol. 154(C), pages 40-50.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Aliaga, D.M. & Romero, C.P. & Feick, R. & Brooks, W.K. & Campbell, A.N., 2024. "Modelling and simulation of a novel liquid air energy storage system with a liquid piston, NH3 and CO2 cycles for enhanced heat and cold utilisation," Applied Energy, Elsevier, vol. 362(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Aliaga, D.M. & Romero, C.P. & Feick, R. & Brooks, W.K. & Campbell, A.N., 2024. "Modelling and simulation of a novel liquid air energy storage system with a liquid piston, NH3 and CO2 cycles for enhanced heat and cold utilisation," Applied Energy, Elsevier, vol. 362(C).
    2. Gouda, El Mehdi & Neu, Thibault & Benaouicha, Mustapha & Fan, Yilin & Subrenat, Albert & Luo, Lingai, 2023. "Experimental and numerical investigation on the flow and heat transfer behaviors during a compression–cooling–expansion cycle using a liquid piston for compressed air energy storage," Energy, Elsevier, vol. 277(C).
    3. Yang, Biao & Li, Deyou & Fu, Xiaolong & Wang, Hongjie & Gong, Ruzhi, 2024. "Energy and exergy analysis of a novel pumped hydro compressed air energy storage system," Energy, Elsevier, vol. 294(C).
    4. Chen, Hao & Wang, Huanran & Li, Ruixiong & Sun, Hao & Ge, Gangqiang & Ling, Lanning, 2022. "Experimental and analytical investigation of near-isothermal pumped hydro-compressed air energy storage system," Energy, Elsevier, vol. 249(C).
    5. Olusola Fajinmi & Josiah L. Munda & Yskandar Hamam & Olawale Popoola, 2023. "Compressed Air Energy Storage as a Battery Energy Storage System for Various Application Domains: A Review," Energies, MDPI, vol. 16(18), pages 1-42, September.
    6. Zhang, Xinjing & Xu, Yujie & Zhou, Xuezhi & Zhang, Yi & Li, Wen & Zuo, Zhitao & Guo, Huan & Huang, Ye & Chen, Haisheng, 2018. "A near-isothermal expander for isothermal compressed air energy storage system," Applied Energy, Elsevier, vol. 225(C), pages 955-964.
    7. Wang, Ke & Cui, Qian & Liu, Yixue & He, Qing, 2024. "Performance analysis of a novel isothermal compressed carbon dioxide energy storage system integrated with solar thermal storage," Energy, Elsevier, vol. 303(C).
    8. Li, Ruixiong & Tao, Rui & Yao, Erren & Chen, Hao & Zhang, Haoran & Xu, Xuefang & Wang, Huanran, 2023. "Comprehensive thermo-exploration of a near-isothermal compressed air energy storage system with a pre-compressing process and heat pump discharging," Energy, Elsevier, vol. 268(C).
    9. Patil, Vikram C. & Acharya, Pinaki & Ro, Paul I., 2020. "Experimental investigation of water spray injection in liquid piston for near-isothermal compression," Applied Energy, Elsevier, vol. 259(C).
    10. Tong, Zheming & Cheng, Zhewu & Tong, Shuiguang, 2021. "A review on the development of compressed air energy storage in China: Technical and economic challenges to commercialization," Renewable and Sustainable Energy Reviews, Elsevier, vol. 135(C).
    11. Shan, Rui & Reagan, Jeremiah & Castellanos, Sergio & Kurtz, Sarah & Kittner, Noah, 2022. "Evaluating emerging long-duration energy storage technologies," Renewable and Sustainable Energy Reviews, Elsevier, vol. 159(C).
    12. Ngangué, Max Ndamé & Stouffs, Pascal, 2020. "Dynamic simulation of an original Joule cycle liquid pistons hot air Ericsson engine," Energy, Elsevier, vol. 190(C).
    13. Chen, Hao & Wang, Huanran & Li, Ruixiong & Sun, Hao & Zhang, Yufei & Ling, Lanning, 2023. "Thermo-dynamic and economic analysis of a novel pumped hydro-compressed air energy storage system combined with compressed air energy storage system as a spray system," Energy, Elsevier, vol. 280(C).
    14. Gouda, El Mehdi & Benaouicha, Mustapha & Neu, Thibault & Fan, Yilin & Luo, Lingai, 2022. "Flow and heat transfer characteristics of air compression in a liquid piston for compressed air energy storage," Energy, Elsevier, vol. 254(PB).
    15. He, Wei & Wang, Jihong, 2018. "Optimal selection of air expansion machine in Compressed Air Energy Storage: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 87(C), pages 77-95.
    16. Chen, Yang & Odukomaiya, Adewale & Kassaee, Saiid & O’Connor, Patrick & Momen, Ayyoub M. & Liu, Xiaobing & Smith, Brennan T., 2019. "Preliminary analysis of market potential for a hydropneumatic ground-level integrated diverse energy storage system," Applied Energy, Elsevier, vol. 242(C), pages 1237-1247.
    17. Luke Aquilina & Tonio Sant & Robert N. Farrugia & John Licari & Cyril Spiteri Staines & Daniel Buhagiar, 2024. "Measurements and Modelling of the Discharge Cycle of a Grid-Connected Hydro-Pneumatic Energy Storage System," Energies, MDPI, vol. 17(7), pages 1-33, March.
    18. Li, Chengchen & Wang, Huanran & He, Xin & Zhang, Yan, 2022. "Experimental and thermodynamic investigation on isothermal performance of large-scaled liquid piston," Energy, Elsevier, vol. 249(C).
    19. Heo, Jin Young & Kim, Min Seok & Baik, Seungjoon & Bae, Seong Jun & Lee, Jeong Ik, 2017. "Thermodynamic study of supercritical CO2 Brayton cycle using an isothermal compressor," Applied Energy, Elsevier, vol. 206(C), pages 1118-1130.
    20. Cheekatamarla, Praveen K. & Kassaee, Saiid & Abu-Heiba, Ahmad & Momen, Ayyoub M., 2022. "Near isothermal compressed air energy storage system in residential and commercial buildings: Techno-economic analysis," Energy, Elsevier, vol. 251(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:357:y:2024:i:c:s0306261923018706. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.