IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v13y2021i10p5379-d552576.html
   My bibliography  Save this article

The Influence of Diesel–Ethanol Fuel Blends on Performance Parameters and Exhaust Emissions: Experimental Investigation and Multi-Objective Optimization of a Diesel Engine

Author

Listed:
  • Behdad Shadidi

    (Department of Biosystem Engineering, Faculty of Agriculture, Bu-Ali Sina University, Hamedan 6517838695, Iran)

  • Hossein Haji Agha Alizade

    (Department of Biosystem Engineering, Faculty of Agriculture, Bu-Ali Sina University, Hamedan 6517838695, Iran)

  • Gholamhassan Najafi

    (Department of Biosystem Engineering, Faculty of Agriculture, Tarbiat Modares University, Tehran 14115111, Iran)

Abstract

Compression combustion engines are a source of air pollutants such as HC and Co, but are still widely used throughout the world. The use of renewable fuels such as ethanol, which is a low-carbon fuel, can reduce the emission of these harmful gases from the engine. A fundamental analysis is proposed in this research to experimentally examine the emission characteristics of diesel–ethanol fuel blends. Furthermore, a multi-objective genetic algorithm (e-MOGA) was developed based on the experimental data obtained to fine the most effective or Pareto set of engine emission and performance optimization solutions. So, the optimization problem had two inputs and seven objectives. For this purpose, input variables for the search space were S (rpm) varied in the range of (1600–2000) and E (%) varied in the range of (0–12). These design variables were chosen to be varied in a prespecified range with a lower and upper band as same as experimental conditions. A diesel engine using (DE2, DE4, DE6, DE8, DE10, and DE12) diesel–ethanol fuel blends, at the various speed of 1600 to 2000 rpm, was utilized for the experiment. The findings showed that the use of diesel–ethanol fuel blends decreased the concentration of CO and HC emissions by 3.2–30.6% and 7.01–16.25%, respectively, due to the high oxygen content of ethanol. As opposed to CO and HC emissions, the NOx concentration showed an increase of 7.5–19.6%. This increase was attributed to the high combustion quality in the combustion chamber, which resulted in a higher combustion chamber temperature. The optimization results confirmed that the shape of the Pareto front obtained from multi-objective ϵ-Pareto optimization could be convex, concave, or a combination of both. A new parameter was introduced as emission index or EI for selection of the best solution among the Pareto set of solutions. This parameter had a minimum value of 4.61. The variables levels for this optimum solution were as follows: engine speed = 1977 rpm, ethanol blend ratio = 10%, CO = 0.27%, CO 2 = 6.81%, HC = 3 ppm, NO x = 1573 ppm, SFC = 239 g/kW·h, P = 56 kW, and T = 269.9 N·m. The EI index had a maximum value of 8.26. Conclusively, we can say that the optimization algorithm was successful in minimizing emission index for all ethanol blend ratios, especially at higher engine speeds.

Suggested Citation

  • Behdad Shadidi & Hossein Haji Agha Alizade & Gholamhassan Najafi, 2021. "The Influence of Diesel–Ethanol Fuel Blends on Performance Parameters and Exhaust Emissions: Experimental Investigation and Multi-Objective Optimization of a Diesel Engine," Sustainability, MDPI, vol. 13(10), pages 1-25, May.
    • Handle: RePEc:gam:jsusta:v:13:y:2021:i:10:p:5379-:d:552576
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/13/10/5379/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/2071-1050/13/10/5379/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. rahimi, Hadi & Ghobadian, Barat & Yusaf, Talal & Najafi, Gholamhasan & Khatamifar, Mahdi, 2009. "Diesterol: An environment-friendly IC engine fuel," Renewable Energy, Elsevier, vol. 34(1), pages 335-342.
    2. Ghobadian, Barat & Najafi, Gholamhassan & Rahimi, Hadi & Yusaf, T.F., 2009. "Future of renewable energies in Iran," Renewable and Sustainable Energy Reviews, Elsevier, vol. 13(3), pages 689-695, April.
    3. Shadidi, Behdad & Yusaf, Talal & Alizadeh, Hossein Haji Agha & Ghobadian, Barat, 2014. "Experimental investigation of the tractor engine performance using diesohol fuel," Applied Energy, Elsevier, vol. 114(C), pages 874-879.
    4. Sarjovaara, Teemu & Alantie, Jussi & Larmi, Martti, 2013. "Ethanol dual-fuel combustion concept on heavy duty engine," Energy, Elsevier, vol. 63(C), pages 76-85.
    5. Li, De-gang & Zhen, Huang & Xingcai, Lŭ & Wu-gao, Zhang & Jian-guang, Yang, 2005. "Physico-chemical properties of ethanol–diesel blend fuel and its effect on performance and emissions of diesel engines," Renewable Energy, Elsevier, vol. 30(6), pages 967-976.
    6. Thangavelu, Saravana Kannan & Ahmed, Abu Saleh & Ani, Farid Nasir, 2016. "Review on bioethanol as alternative fuel for spark ignition engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 56(C), pages 820-835.
    7. Deh Kiani, M. Kiani & Ghobadian, B. & Tavakoli, T. & Nikbakht, A.M. & Najafi, G., 2010. "Application of artificial neural networks for the prediction of performance and exhaust emissions in SI engine using ethanol- gasoline blends," Energy, Elsevier, vol. 35(1), pages 65-69.
    8. Nawar Al-Esawi & Mansour Al Qubeissi & Ruslana Kolodnytska, 2019. "The Impact of Biodiesel Fuel on Ethanol/Diesel Blends," Energies, MDPI, vol. 12(9), pages 1-11, May.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Vallinayagam, R. & Vedharaj, S. & Yang, W.M. & Roberts, W.L. & Dibble, R.W., 2015. "Feasibility of using less viscous and lower cetane (LVLC) fuels in a diesel engine: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 51(C), pages 1166-1190.
    2. Safieddin Ardebili, M. & Ghobadian, B. & Najafi, G. & Chegeni, A., 2011. "Biodiesel production potential from edible oil seeds in Iran," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(6), pages 3041-3044, August.
    3. Hosseini, Seyed Ehsan & Andwari, Amin Mahmoudzadeh & Wahid, Mazlan Abdul & Bagheri, Ghobad, 2013. "A review on green energy potentials in Iran," Renewable and Sustainable Energy Reviews, Elsevier, vol. 27(C), pages 533-545.
    4. Wei, Liangjie & Cheung, C.S. & Huang, Zuohua, 2014. "Effect of n-pentanol addition on the combustion, performance and emission characteristics of a direct-injection diesel engine," Energy, Elsevier, vol. 70(C), pages 172-180.
    5. Kandasamy, Senthil Kumar & Selvaraj, Arun Saco & Rajagopal, Thundil Karuppa Raj, 2019. "Experimental investigations of ethanol blended biodiesel fuel on automotive diesel engine performance, emission and durability characteristics," Renewable Energy, Elsevier, vol. 141(C), pages 411-419.
    6. Odziemkowska, Małgorzata & Matuszewska, Anna & Czarnocka, Joanna, 2016. "Diesel oil with bioethanol as a fuel for compression-ignition engines," Applied Energy, Elsevier, vol. 184(C), pages 1264-1272.
    7. Yusri, I.M. & Mamat, R. & Najafi, G. & Razman, A. & Awad, Omar I. & Azmi, W.H. & Ishak, W.F.W. & Shaiful, A.I.M., 2017. "Alcohol based automotive fuels from first four alcohol family in compression and spark ignition engine: A review on engine performance and exhaust emissions," Renewable and Sustainable Energy Reviews, Elsevier, vol. 77(C), pages 169-181.
    8. Obed M. Ali & Talal Yusaf & Rizalman Mamat & Nik R. Abdullah & Abdul Adam Abdullah, 2014. "Influence of Chemical Blends on Palm Oil Methyl Esters’ Cold Flow Properties and Fuel Characteristics," Energies, MDPI, vol. 7(7), pages 1-17, July.
    9. Zhu, Lifeng & Qian, Yong & Wang, Xiaole & Lu, Xingcai, 2015. "Effects of direct injection timing and premixed ratio on combustion and emissions characteristics of RCCI (Reactivity Controlled Compression Ignition) with N-heptane/gasoline-like fuels," Energy, Elsevier, vol. 93(P1), pages 383-392.
    10. Zaharin, M.S.M. & Abdullah, N.R. & Najafi, G. & Sharudin, H. & Yusaf, T., 2017. "Effects of physicochemical properties of biodiesel fuel blends with alcohol on diesel engine performance and exhaust emissions: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 475-493.
    11. Pradelle, Florian & Leal Braga, Sergio & Fonseca de Aguiar Martins, Ana Rosa & Turkovics, Franck & Nohra Chaar Pradelle, Renata, 2019. "Performance and combustion characteristics of a compression ignition engine running on diesel-biodiesel-ethanol (DBE) blends – Potential as diesel fuel substitute on an Euro III engine," Renewable Energy, Elsevier, vol. 136(C), pages 586-598.
    12. Shadidi, Behdad & Yusaf, Talal & Alizadeh, Hossein Haji Agha & Ghobadian, Barat, 2014. "Experimental investigation of the tractor engine performance using diesohol fuel," Applied Energy, Elsevier, vol. 114(C), pages 874-879.
    13. Shahir, S.A. & Masjuki, H.H. & Kalam, M.A. & Imran, A. & Ashraful, A.M., 2015. "Performance and emission assessment of diesel–biodiesel–ethanol/bioethanol blend as a fuel in diesel engines: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 48(C), pages 62-78.
    14. Qian, Yong & Wang, Xiaole & Zhu, Lifeng & Lu, Xingcai, 2015. "Experimental studies on combustion and emissions of RCCI (reactivity controlled compression ignition) with gasoline/n-heptane and ethanol/n-heptane as fuels," Energy, Elsevier, vol. 88(C), pages 584-594.
    15. Shahir, S.A. & Masjuki, H.H. & Kalam, M.A. & Imran, A. & Fattah, I.M. Rizwanul & Sanjid, A., 2014. "Feasibility of diesel–biodiesel–ethanol/bioethanol blend as existing CI engine fuel: An assessment of properties, material compatibility, safety and combustion," Renewable and Sustainable Energy Reviews, Elsevier, vol. 32(C), pages 379-395.
    16. Telli, Giovani Dambros & Altafini, Carlos Roberto & Rosa, Josimar Souza & Costa, Carlos Alberto, 2018. "Experimental investigation of a compression ignition engine operating on B7 direct injected and hydrous ethanol fumigation," Energy, Elsevier, vol. 165(PB), pages 106-117.
    17. Artur Krzemiński & Adam Ustrzycki, 2023. "Effect of Ethanol Added to Diesel Fuel on the Range of Fuel Spray," Energies, MDPI, vol. 16(4), pages 1-15, February.
    18. Chintala, V. & Subramanian, K.A., 2015. "Experimental investigations on effect of different compression ratios on enhancement of maximum hydrogen energy share in a compression ignition engine under dual-fuel mode," Energy, Elsevier, vol. 87(C), pages 448-462.
    19. Ozsezen, Ahmet Necati & Canakci, Mustafa, 2011. "Performance and combustion characteristics of alcohol–gasoline blends at wide-open throttle," Energy, Elsevier, vol. 36(5), pages 2747-2752.
    20. Kumar, Atul & Chen, Hsien-Wen & Yang, Shouyin, 2023. "Modeling microexplosion mechanism in droplet combustion: Puffing and droplet breakup," Energy, Elsevier, vol. 266(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:13:y:2021:i:10:p:5379-:d:552576. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.