IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v16y2023i13p4916-d1178075.html
   My bibliography  Save this article

Design for a Heat Pump with Sink Temperatures of 200 °C Using a Radial Compressor

Author

Listed:
  • Julian Unterluggauer

    (Center for Energy, Austrian Institute of Technology, 1210 Vienna, Austria)

  • Verena Sulzgruber

    (Center for Energy, Austrian Institute of Technology, 1210 Vienna, Austria)

  • Clemens Kroiss

    (Institute of Energy Systems and Thermodynamics, TU Wien, 1060 Vienna, Austria)

  • Johannes Riedl

    (Center for Energy, Austrian Institute of Technology, 1210 Vienna, Austria)

  • Reinhard Jentsch

    (Center for Energy, Austrian Institute of Technology, 1210 Vienna, Austria)

  • Reinhard Willinger

    (Institute of Energy Systems and Thermodynamics, TU Wien, 1060 Vienna, Austria)

Abstract

To reduce CO 2 emissions in the industrial sector, high-temperature heat pumps are a key technology. This work presents an approach to design such an industrial heat pump system capable of supplying 200 ° C sink temperature and a capacity of approximately 1 MW. Today’s market-available heat pumps using displacement compressors are not suitable for reaching that high sink temperatures as they need lubricating oil, which is not temperature resistant enough. As a consequence, in this study a transcritical heat pump cycle using a two-stage oil-free radial compressor is investigated. Based on preliminary studies, R1233zd(E) is chosen as a refrigerant. The procedure couples 1D thermodynamic cycle simulations with a radial compressor mean-line design model. A preliminary geometry for a compressor with and without inlet guide vanes is presented, and compressor maps including the compressors behaviour in off-design are calculated. The compressor design is then imported into a 1D simulation to analysis the performance of the heat pump in the whole operating range. In the analysis, the application of a fixed inlet is evaluated, and an improvement of approximately 21% and 16% of the isentropic efficiency is achieved. The thermodynamic simulations showed a maximum COP of approximately 2.8 and a possible operating range of 0.5 to 1.3 MW thermal power. Furthermore, a techno-economical analysis by means of a deep-fryer use case showed reasonable payback times of between 2 and 10 years, depending on the electricity to gas price ratio.

Suggested Citation

  • Julian Unterluggauer & Verena Sulzgruber & Clemens Kroiss & Johannes Riedl & Reinhard Jentsch & Reinhard Willinger, 2023. "Design for a Heat Pump with Sink Temperatures of 200 °C Using a Radial Compressor," Energies, MDPI, vol. 16(13), pages 1-21, June.
    • Handle: RePEc:gam:jeners:v:16:y:2023:i:13:p:4916-:d:1178075
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/16/13/4916/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/16/13/4916/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Lecompte, Steven & Huisseune, Henk & van den Broek, Martijn & Vanslambrouck, Bruno & De Paepe, Michel, 2015. "Review of organic Rankine cycle (ORC) architectures for waste heat recovery," Renewable and Sustainable Energy Reviews, Elsevier, vol. 47(C), pages 448-461.
    2. Moein Shamoushaki & Pouriya H. Niknam & Lorenzo Talluri & Giampaolo Manfrida & Daniele Fiaschi, 2021. "Development of Cost Correlations for the Economic Assessment of Power Plant Equipment," Energies, MDPI, vol. 14(9), pages 1-19, May.
    3. Meroni, Andrea & Zühlsdorf, Benjamin & Elmegaard, Brian & Haglind, Fredrik, 2018. "Design of centrifugal compressors for heat pump systems," Applied Energy, Elsevier, vol. 232(C), pages 139-156.
    4. Schiffmann, J. & Favrat, D., 2010. "Design, experimental investigation and multi-objective optimization of a small-scale radial compressor for heat pump applications," Energy, Elsevier, vol. 35(1), pages 436-450.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Uusitalo, Antti & Turunen-Saaresti, Teemu & Honkatukia, Juha & Tiainen, Jonna & Jaatinen-Värri, Ahti, 2020. "Numerical analysis of working fluids for large scale centrifugal compressor driven cascade heat pumps upgrading waste heat," Applied Energy, Elsevier, vol. 269(C).
    2. Wang, Y. & Wang, J. & He, W., 2022. "Development of efficient, flexible and affordable heat pumps for supporting heat and power decarbonisation in the UK and beyond: Review and perspectives," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    3. Fabien Marty & Sylvain Serra & Sabine Sochard & Jean-Michel Reneaume, 2019. "Exergy Analysis and Optimization of a Combined Heat and Power Geothermal Plant," Energies, MDPI, vol. 12(6), pages 1-22, March.
    4. Bamorovat Abadi, Gholamreza & Kim, Kyung Chun, 2017. "Investigation of organic Rankine cycles with zeotropic mixtures as a working fluid: Advantages and issues," Renewable and Sustainable Energy Reviews, Elsevier, vol. 73(C), pages 1000-1013.
    5. Christoph J.W. Kirmse & Oyeniyi A. Oyewunmi & Andrew J. Haslam & Christos N. Markides, 2016. "Comparison of a Novel Organic-Fluid Thermofluidic Heat Converter and an Organic Rankine Cycle Heat Engine," Energies, MDPI, vol. 9(7), pages 1-26, June.
    6. Krail, Jürgen & Beckmann, Georg & Schittl, Florian & Piringer, Gerhard, 2023. "Comparative thermodynamic analysis of an improved ORC process with integrated injection of process fluid," Energy, Elsevier, vol. 266(C).
    7. Yang, Wei & Bao, Jingjing & Liu, Hongtao & Zhang, Jun & Guo, Lin, 2023. "Low-grade heat to hydrogen: Current technologies, challenges and prospective," Renewable and Sustainable Energy Reviews, Elsevier, vol. 188(C).
    8. Liu, Hua & Zhao, Baiyang & Zhang, Zhiping & Li, Hongbo & Hu, Bin & Wang, R.Z., 2020. "Experimental validation of an advanced heat pump system with high-efficiency centrifugal compressor," Energy, Elsevier, vol. 213(C).
    9. Menon, Ramanunni P. & Paolone, Mario & Maréchal, François, 2013. "Study of optimal design of polygeneration systems in optimal control strategies," Energy, Elsevier, vol. 55(C), pages 134-141.
    10. Li, Wenjia & Hao, Yong, 2017. "Efficient solar power generation combining photovoltaics and mid-/low-temperature methanol thermochemistry," Applied Energy, Elsevier, vol. 202(C), pages 377-385.
    11. Chen, Weixiong & Qian, Yiran & Tang, Xin & Fang, Huawei & Yi, Jingwei & Liang, Tiebo & Zhao, Quanbin & Yan, Junjie, 2023. "System-component combined design and comprehensive evaluation of closed-air Brayton cycle," Energy, Elsevier, vol. 278(C).
    12. Baccioli, A. & Antonelli, M. & Desideri, U., 2017. "Technical and economic analysis of organic flash regenerative cycles (OFRCs) for low temperature waste heat recovery," Applied Energy, Elsevier, vol. 199(C), pages 69-87.
    13. Imran, Muhammad & Haglind, Fredrik & Asim, Muhammad & Zeb Alvi, Jahan, 2018. "Recent research trends in organic Rankine cycle technology: A bibliometric approach," Renewable and Sustainable Energy Reviews, Elsevier, vol. 81(P1), pages 552-562.
    14. Somchart Chantasiriwan, 2023. "Reduction in Fuel Consumption in Biomass-Fired Power Plant Using Hybrid Drying System," Energies, MDPI, vol. 16(17), pages 1-14, August.
    15. Osorio, Julian D. & Panwar, Mayank & Rivera-Alvarez, Alejandro & Chryssostomidis, Chrys & Hovsapian, Rob & Mohanpurkar, Manish & Chanda, Sayonsom & Williams, Herbert, 2020. "Enabling thermal efficiency improvement and waste heat recovery using liquid air harnessed from offshore renewable energy sources," Applied Energy, Elsevier, vol. 275(C).
    16. Sindu Daniarta & Magdalena Nemś & Piotr Kolasiński & Michał Pomorski, 2022. "Sizing the Thermal Energy Storage Device Utilizing Phase Change Material (PCM) for Low-Temperature Organic Rankine Cycle Systems Employing Selected Hydrocarbons," Energies, MDPI, vol. 15(3), pages 1-19, January.
    17. Hossein Nami & Amjad Anvari-Moghaddam & Ahmad Arabkoohsar & Amir Reza Razmi, 2020. "4E Analyses of a Hybrid Waste-Driven CHP–ORC Plant with Flue Gas Condensation," Sustainability, MDPI, vol. 12(22), pages 1-21, November.
    18. Zhang, Fengtao & Zhang, Jianyuan & You, Jinggang & Yang, Liyong & Wang, Wei & Luo, Qing & Jiao, Ligang & Liu, Zhengang & Jin, Quan & Wang, Hao, 2024. "Construction of multi-loop thermodynamic cycles: Methodology and case study," Energy, Elsevier, vol. 288(C).
    19. Marian Piwowarski & Krzysztof Kosowski & Marcin Richert, 2023. "Organic Supercritical Thermodynamic Cycles with Isothermal Turbine," Energies, MDPI, vol. 16(12), pages 1-17, June.
    20. Patrick Linke & Athanasios I. Papadopoulos & Panos Seferlis, 2015. "Systematic Methods for Working Fluid Selection and the Design, Integration and Control of Organic Rankine Cycles—A Review," Energies, MDPI, vol. 8(6), pages 1-47, May.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:16:y:2023:i:13:p:4916-:d:1178075. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.