IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i23p9253-d995400.html
   My bibliography  Save this article

Numerical Modeling of Shell-and-Tube-like Elastocaloric Regenerator

Author

Listed:
  • Žiga Ahčin

    (Faculty of Mechanical Engineering, University of Ljubljana, Aškerčeva 6, 1000 Ljubljana, Slovenia)

  • Parham Kabirifar

    (Faculty of Mechanical Engineering, University of Ljubljana, Aškerčeva 6, 1000 Ljubljana, Slovenia)

  • Luka Porenta

    (Faculty of Mechanical Engineering, University of Ljubljana, Aškerčeva 6, 1000 Ljubljana, Slovenia)

  • Miha Brojan

    (Faculty of Mechanical Engineering, University of Ljubljana, Aškerčeva 6, 1000 Ljubljana, Slovenia)

  • Jaka Tušek

    (Faculty of Mechanical Engineering, University of Ljubljana, Aškerčeva 6, 1000 Ljubljana, Slovenia)

Abstract

Elastocaloric cooling is considered an environmentally friendly future alternative to vapor-compression technology. Recently, a shell-and-tube-like elastocaloric regenerator loaded in compression has demonstrated record-breaking heat-pumping performance and fatigue-resistant operation. The aim of this work is thus to present a new 1D numerical model to simulate and optimize the operation of an elastocaloric regenerator with a shell-and-tube-like design. In the first part of this work, the superelastic and elastocaloric properties of a single NiTi tube, which serve as input data for the numerical model, were determined through experimental characterization and phenomenological modeling. In the second part, the results of the numerical model were compared with the experimentally obtained results. Relatively good agreement was found regarding the temperature span, cooling and heating power, and COP values, which indicates that the developed numerical model could be used for accurate optimization of shell-and-tube-like elastocaloric regenerators. Finally, the effects of operating conditions and hysteresis losses on the performance of the shell-and-tube-like elastocaloric regenerator are modeled and discussed. This work shows that the shell-and-tube-like elastocaloric regenerator with this configuration can achieve a maximum temperature span of more than 50 K at zero-thermal-load conditions and a maximum cooling/heating power of up to 4000 W·kg −1 and COP of about 4 (at zero temperature span).

Suggested Citation

  • Žiga Ahčin & Parham Kabirifar & Luka Porenta & Miha Brojan & Jaka Tušek, 2022. "Numerical Modeling of Shell-and-Tube-like Elastocaloric Regenerator," Energies, MDPI, vol. 15(23), pages 1-28, December.
    • Handle: RePEc:gam:jeners:v:15:y:2022:i:23:p:9253-:d:995400
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/23/9253/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/15/23/9253/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Qian, Suxin & Yuan, Lifen & Yu, Jianlin & Yan, Gang, 2017. "Numerical modeling of an active elastocaloric regenerator refrigerator with phase transformation kinetics and the matching principle for materials selection," Energy, Elsevier, vol. 141(C), pages 744-756.
    2. Luo, Dong & Feng, Yinshan & Verma, Parmesh, 2017. "Modeling and analysis of an integrated solid state elastocaloric heat pumping system," Energy, Elsevier, vol. 130(C), pages 500-514.
    3. Han, Yuan & Lai, Cong & Li, Jiarui & Zhang, Zhufeng & Zhang, Houcheng & Hou, Shujin & Wang, Fu & Zhao, Jiapei & Zhang, Chunfei & Miao, He & Yuan, Jinliang, 2022. "Elastocaloric cooler for waste heat recovery from proton exchange membrane fuel cells," Energy, Elsevier, vol. 238(PA).
    4. Nora Bachmann & Daniel Schwarz & David Bach & Olaf Schäfer-Welsen & Thomas Koch & Kilian Bartholomé, 2022. "Modeling of an Elastocaloric Cooling System for Determining Efficiency," Energies, MDPI, vol. 15(14), pages 1-14, July.
    5. Tan, Jianming & Wang, Yao & Xu, Shijie & Liu, Huaican & Qian, Suxin, 2020. "Thermodynamic cycle analysis of heat driven elastocaloric cooling system," Energy, Elsevier, vol. 197(C).
    6. Qian, Suxin & Wang, Yao & Yuan, Lifen & Yu, Jianlin, 2019. "A heat driven elastocaloric cooling system," Energy, Elsevier, vol. 182(C), pages 881-899.
    7. Mubarak Ismail & Metkel Yebiyo & Issa Chaer, 2021. "A Review of Recent Advances in Emerging Alternative Heating and Cooling Technologies," Energies, MDPI, vol. 14(2), pages 1-24, January.
    8. Qian, Suxin & Wang, Yao & Xu, Shijie & Chen, Yanliang & Yuan, Lifen & Yu, Jianlin, 2021. "Cascade utilization of low-grade thermal energy by coupled elastocaloric power and cooling cycle," Applied Energy, Elsevier, vol. 298(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Lu, Zhen & Huang, Yuewu & Zhao, Yonggang, 2023. "Elastocaloric cooler for waste heat recovery from perovskite solar cell with electricity and cooling production," Renewable Energy, Elsevier, vol. 215(C).
    2. Han, Yuan & Lai, Cong & Li, Jiarui & Zhang, Zhufeng & Zhang, Houcheng & Hou, Shujin & Wang, Fu & Zhao, Jiapei & Zhang, Chunfei & Miao, He & Yuan, Jinliang, 2022. "Elastocaloric cooler for waste heat recovery from proton exchange membrane fuel cells," Energy, Elsevier, vol. 238(PA).
    3. Han, Yuan & Zhang, Houcheng, 2022. "Potentiality of elastocaloric cooling system for high-temperature proton exchange membrane fuel cell waste heat harvesting," Renewable Energy, Elsevier, vol. 200(C), pages 1166-1179.
    4. Tan, Jianming & Wang, Yao & Xu, Shijie & Liu, Huaican & Qian, Suxin, 2020. "Thermodynamic cycle analysis of heat driven elastocaloric cooling system," Energy, Elsevier, vol. 197(C).
    5. Zhao, Qin & Li, Pengcheng & Zhang, Houcheng, 2024. "Dually boosting the performance of photovoltaic module via integrating elastocaloric cooler," Energy, Elsevier, vol. 295(C).
    6. Qian, Suxin & Yao, Sijia & Wang, Yao & Yuan, Lifen & Yu, Jianlin, 2022. "Harvesting low-grade heat by coupling regenerative shape-memory actuator and piezoelectric generator," Applied Energy, Elsevier, vol. 322(C).
    7. Qian, Suxin & Wang, Yao & Xu, Shijie & Chen, Yanliang & Yuan, Lifen & Yu, Jianlin, 2021. "Cascade utilization of low-grade thermal energy by coupled elastocaloric power and cooling cycle," Applied Energy, Elsevier, vol. 298(C).
    8. Jongchansitto, P. & Yachai, T. & Preechawuttipong, I. & Boufayed, R. & Balandraud, X., 2021. "Concept of mechanocaloric granular material made from shape memory alloy," Energy, Elsevier, vol. 219(C).
    9. Zhang, Jiongjiong & Zhu, Yuxiang & Cheng, Siyuan & Yao, Shuhuai & Sun, Qingping, 2023. "Effect of inactive section on cooling performance of compressive elastocaloric refrigeration prototype," Applied Energy, Elsevier, vol. 351(C).
    10. Ma, Liuyang & Zhao, Qin & Zhang, Houcheng & Hou, Shujin & Zhao, Jiapei & Wang, Fu & Zhang, Chunfei & Miao, He & Yuan, Jinliang, 2022. "Performance analysis of a concentrated photovoltaic cell-elastocaloric cooler hybrid system for power and cooling cogeneration," Energy, Elsevier, vol. 239(PD).
    11. Aprea, C. & Greco, A. & Maiorino, A. & Masselli, C., 2020. "The use of barocaloric effect for energy saving in a domestic refrigerator with ethylene-glycol based nanofluids: A numerical analysis and a comparison with a vapor compression cooler," Energy, Elsevier, vol. 190(C).
    12. Aprea, C. & Greco, A. & Maiorino, A. & Masselli, C., 2018. "Solid-state refrigeration: A comparison of the energy performances of caloric materials operating in an active caloric regenerator," Energy, Elsevier, vol. 165(PA), pages 439-455.
    13. Luca Cirillo & Adriana Greco & Claudia Masselli, 2023. "The Application of Barocaloric Solid-State Cooling in the Cold Food Chain for Carbon Footprint Reduction," Energies, MDPI, vol. 16(18), pages 1-17, September.
    14. Zhang, Yong & He, Shirong & Jiang, Xiaohui & Xiong, Mu & Ye, Yuntao & Yang, Xi, 2023. "Three-dimensional multi-phase simulation of proton exchange membrane fuel cell performance considering constriction straight channel," Energy, Elsevier, vol. 267(C).
    15. Zhang, Xin & Li, Jingwen & Xiong, Yi & Ang, Yee Sin, 2022. "Efficient harvesting of low-grade waste heat from proton exchange membrane fuel cells via thermoradiative power devices," Energy, Elsevier, vol. 258(C).
    16. Riccardo Fraboni & Gianluca Grazieschi & Simon Pezzutto & Benjamin Mitterrutzner & Eric Wilczynski, 2023. "Environmental Assessment of Residential Space Heating and Cooling Technologies in Europe: A Review of 11 European Member States," Sustainability, MDPI, vol. 15(5), pages 1-22, February.
    17. Wang, Mingli & Ruan, Jiafen & Zhang, Jian & Jiang, Yefan & Gao, Fei & Zhang, Xin & Rahman, Ehsanur & Guo, Juncheng, 2024. "Modeling, thermodynamic performance analysis, and parameter optimization of a hybrid power generation system coupling thermogalvanic cells with alkaline fuel cells," Energy, Elsevier, vol. 292(C).
    18. Mubarak Ismail & Metkel Yebiyo & Issa Chaer, 2021. "A Review of Recent Advances in Emerging Alternative Heating and Cooling Technologies," Energies, MDPI, vol. 14(2), pages 1-24, January.
    19. Chdil, O. & Bikerouin, M. & Balli, M. & Mounkachi, O., 2023. "New horizons in magnetic refrigeration using artificial intelligence," Applied Energy, Elsevier, vol. 335(C).
    20. Wang, Yao & Wang, Qianlong & Yu, Jianlin & Qian, Suxin, 2023. "A heat pump dual temperature display cabinet using natural refrigerants," Applied Energy, Elsevier, vol. 330(PB).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:23:p:9253-:d:995400. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.