IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v12y2019i2p283-d198554.html
   My bibliography  Save this article

Simulation of the Filling Capability in Vane Pumps

Author

Listed:
  • Massimo Rundo

    (Department of Energy, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy)

  • Giorgio Altare

    (Department of Energy, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy)

  • Paolo Casoli

    (Industrial Engineering Department, University of Parma, Parco Area delle Scienze 181/A, 43124 Parma, Italy)

Abstract

In positive displacement pumps, the main volumetric loss at high speed is due to the incomplete filling of the variable volume chambers. The prediction of the limit speed and of the maximum flow rate delivered by a pump can be obtained only through Computational Fluid Dynamics (CFD) simulations, since the shape, the orientation, and the movement of the chambers with respect to the inlet volume must be considered, along with the non-uniform distribution of the gaseous phase, due to the dissolved air release. In this paper, the influence of different geometric parameters on the filling of a vane pump has been investigated through the commercial software PumpLinx ® . At first, a model of a reference pump has been created and validated with different configurations of the suction flow area, then a simplified model has been used for assessing the influence of the geometry of the rotating assembly. It was found that a pump with a low ratio between the axial thickness and the diameter has a higher volumetric efficiency if the chambers are fed from one side only. Opposite behaviors were found in the case of pumps with small diameters and high thicknesses. Moreover, the filling could be improved by increasing the number of chambers, and by reducing the diameter of the rotor, even only locally.

Suggested Citation

  • Massimo Rundo & Giorgio Altare & Paolo Casoli, 2019. "Simulation of the Filling Capability in Vane Pumps," Energies, MDPI, vol. 12(2), pages 1-18, January.
  • Handle: RePEc:gam:jeners:v:12:y:2019:i:2:p:283-:d:198554
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/12/2/283/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/12/2/283/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Massimo Rundo, 2017. "Models for Flow Rate Simulation in Gear Pumps: A Review," Energies, MDPI, vol. 10(9), pages 1-32, August.
    2. Paolo Casoli & Andrea Bedotti & Federico Campanini & Mirko Pastori, 2018. "A Methodology Based on Cyclostationary Analysis for Fault Detection of Hydraulic Axial Piston Pumps," Energies, MDPI, vol. 11(7), pages 1-19, July.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Thomas Lobsinger & Timm Hieronymus & Hubert Schwarze & Gunther Brenner, 2021. "A CFD-Based Comparison of Different Positive Displacement Pumps for Application in Future Automatic Transmission Systems," Energies, MDPI, vol. 14(9), pages 1-24, April.
    2. Paolo Casoli & Mirko Pastori & Fabio Scolari & Massimo Rundo, 2019. "A Vibration Signal-Based Method for Fault Identification and Classification in Hydraulic Axial Piston Pumps," Energies, MDPI, vol. 12(5), pages 1-18, March.
    3. Thomas Lobsinger & Timm Hieronymus & Gunther Brenner, 2020. "A CFD Investigation of a 2D Balanced Vane Pump Focusing on Leakage Flows and Multiphase Flow Characteristics," Energies, MDPI, vol. 13(13), pages 1-24, June.
    4. Paolo Casoli & Carlo Maria Vescovini & Fabio Scolari & Massimo Rundo, 2022. "Theoretical Analysis of Active Flow Ripple Control in Positive Displacement Pumps," Energies, MDPI, vol. 15(13), pages 1-22, June.
    5. Paolo Casoli & Fabio Scolari & Massimo Rundo & Antonio Lettini & Manuel Rigosi, 2020. "CFD Analyses of Textured Surfaces for Tribological Improvements in Hydraulic Pumps," Energies, MDPI, vol. 13(21), pages 1-22, November.
    6. Fatigati, Fabio & Di Bartolomeo, Marco & Cipollone, Roberto, 2022. "Development and experimental assessment of a Low Speed Sliding Rotary Vane Pump for heavy duty engine cooling systems," Applied Energy, Elsevier, vol. 327(C).
    7. Alessandro Corvaglia & Massimo Rundo & Paolo Casoli & Antonio Lettini, 2021. "Evaluation of Tooth Space Pressure and Incomplete Filling in External Gear Pumps by Means of Three-Dimensional CFD Simulations," Energies, MDPI, vol. 14(2), pages 1-16, January.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Pedro Javier Gamez-Montero & Ernest Bernat-Maso, 2022. "Taguchi Techniques as an Effective Simulation-Based Strategy in the Design of Numerical Simulations to Assess Contact Stress in Gerotor Pumps," Energies, MDPI, vol. 15(19), pages 1-24, September.
    2. Paolo Casoli & Mirko Pastori & Fabio Scolari & Massimo Rundo, 2019. "A Vibration Signal-Based Method for Fault Identification and Classification in Hydraulic Axial Piston Pumps," Energies, MDPI, vol. 12(5), pages 1-18, March.
    3. Barbara Zardin & Emiliano Natali & Massimo Borghi, 2019. "Evaluation of the Hydro—Mechanical Efficiency of External Gear Pumps," Energies, MDPI, vol. 12(13), pages 1-19, June.
    4. Pedro Javier Gamez-Montero & Esteve Codina & Robert Castilla, 2019. "A Review of Gerotor Technology in Hydraulic Machines," Energies, MDPI, vol. 12(12), pages 1-44, June.
    5. Valeriy Sanchugov & Pavel Rekadze, 2022. "New Method to Determine the Dynamic Fluid Flow Rate at the Gear Pump Outlet," Energies, MDPI, vol. 15(9), pages 1-29, May.
    6. Gabriele Muzzioli & Luca Montorsi & Andrea Polito & Andrea Lucchi & Alessandro Sassi & Massimo Milani, 2021. "About the Influence of Eco-Friendly Fluids on the Performance of an External Gear Pump," Energies, MDPI, vol. 14(4), pages 1-26, February.
    7. Alessandro Corvaglia & Massimo Rundo & Paolo Casoli & Antonio Lettini, 2021. "Evaluation of Tooth Space Pressure and Incomplete Filling in External Gear Pumps by Means of Three-Dimensional CFD Simulations," Energies, MDPI, vol. 14(2), pages 1-16, January.
    8. Hirokami, Arata & Heshmat, Samia & Tomioka, Satoshi, 2021. "Accurate numerical method to solve flux distribution of Poisson’s equation," Mathematics and Computers in Simulation (MATCOM), Elsevier, vol. 190(C), pages 329-342.
    9. Ionuţ Gabriel Ghionea, 2022. "Applied Methodology for Designing and Calculating a Family of Spur Gear Pumps," Energies, MDPI, vol. 15(12), pages 1-19, June.
    10. Gianluca Marinaro & Emma Frosina & Adolfo Senatore, 2021. "A Numerical Analysis of an Innovative Flow Ripple Reduction Method for External Gear Pumps," Energies, MDPI, vol. 14(2), pages 1-22, January.
    11. Miquel Torrent & Pedro Javier Gamez-Montero & Esteban Codina, 2021. "Parameterization, Modeling, and Validation in Real Conditions of an External Gear Pump," Sustainability, MDPI, vol. 13(6), pages 1-20, March.
    12. Paolo Casoli & Fabio Scolari & Massimo Rundo & Antonio Lettini & Manuel Rigosi, 2020. "CFD Analyses of Textured Surfaces for Tribological Improvements in Hydraulic Pumps," Energies, MDPI, vol. 13(21), pages 1-22, November.
    13. Puliti, Marco & Galluzzi, Renato & Tessari, Federico & Amati, Nicola & Tonoli, Andrea, 2024. "Energy efficient design of regenerative shock absorbers for automotive suspensions: A multi-objective optimization framework," Applied Energy, Elsevier, vol. 358(C).

    More about this item

    Keywords

    CFD; pump filling; vane pump;
    All these keywords.

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:12:y:2019:i:2:p:283-:d:198554. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.