IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v11y2018i8p1959-d160452.html
   My bibliography  Save this article

Compound Heat Transfer Enhancement of Wavy Fin-and-Tube Heat Exchangers through Boundary Layer Restarting and Swirled Flow

Author

Listed:
  • Ali Sadeghianjahromi

    (Department of Mechanical and Aerospace Engineering, Malek-Ashtar University of Technology, Shahin-shahr, P.O. Box 83145/115, Isfahan, Iran)

  • Saeid Kheradmand

    (Department of Mechanical and Aerospace Engineering, Malek-Ashtar University of Technology, Shahin-shahr, P.O. Box 83145/115, Isfahan, Iran)

  • Hossain Nemati

    (Department of Mechanics, Marvdasht Branch, Islamic Azad University, Marvdasht 73711-13119, Iran)

  • Jane-Sunn Liaw

    (Green Energy & Environment Research Laboratories, Industrial Technology Research Institute, Hsinchu 310, Taiwan)

  • Chi-Chuan Wang

    (Department of Mechanical Engineering, National Chiao Tung University, EE474, 1001 University Road, Hsinchu 300, Taiwan)

Abstract

This study performs a 3D turbulent flow numerical simulation to improve heat transfer characteristics of wavy fin-and-tube heat exchangers. A compound design encompassing louver, flat, and vortex generator onto wavy fins can significantly enhance the heat transfer performance of wavy fin-and-tube heat exchangers. Replacement of wavy fins around tubes with flat fins is not effective as far as the reduction of thermal resistance is concerned, although an appreciable pressure drop reduction can be achieved. Adding two louvers with a width of 8 mm to the flat portion can reduce thermal resistance up to 6% in comparison with the reference wavy fin. Increasing the louver number and width can further decrease the thermal resistance. Also, it is found that the optimum louver angle is equal to the wavy angle for offering the lowest thermal resistance. Therefore, compound geometry with three louvers, a width of 12 mm, and the louver angle being equal to wavy angle with waffle height to be the same as fin pitch of the reference wavy fin has the most reduction in thermal resistance of 16% for a pumping power of 0.001 W. Adding punching longitudinal vortex generators on this compound geometry can further decrease thermal resistance up to 18%.

Suggested Citation

  • Ali Sadeghianjahromi & Saeid Kheradmand & Hossain Nemati & Jane-Sunn Liaw & Chi-Chuan Wang, 2018. "Compound Heat Transfer Enhancement of Wavy Fin-and-Tube Heat Exchangers through Boundary Layer Restarting and Swirled Flow," Energies, MDPI, vol. 11(8), pages 1-19, July.
  • Handle: RePEc:gam:jeners:v:11:y:2018:i:8:p:1959-:d:160452
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/11/8/1959/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/11/8/1959/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Moo-Yeon Lee & Yongchan Kim & Dong-Yeon Lee, 2012. "Experimental Study on Frost Height of Round Plate Fin-Tube Heat Exchangers for Mobile Heat Pumps," Energies, MDPI, vol. 5(9), pages 1-13, September.
    2. Arslan Saleem & Man-Hoe Kim, 2017. "CFD Analysis on the Air-Side Thermal-Hydraulic Performance of Multi-Louvered Fin Heat Exchangers at Low Reynolds Numbers," Energies, MDPI, vol. 10(6), pages 1-22, June.
    3. Yonghong Guo & Tongrui Cheng & Xiaoze Du & Lijun Yang, 2017. "Anti-Freezing Mechanism Analysis of a Finned Flat Tube in an Air-Cooled Condenser," Energies, MDPI, vol. 10(11), pages 1-21, November.
    4. Lotfi, Babak & Sundén, Bengt & Wang, Qiuwang, 2016. "An investigation of the thermo-hydraulic performance of the smooth wavy fin-and-elliptical tube heat exchangers utilizing new type vortex generators," Applied Energy, Elsevier, vol. 162(C), pages 1282-1302.
    5. Yuan Xue & Zhihua Ge & Xiaoze Du & Lijun Yang, 2018. "On the Heat Transfer Enhancement of Plate Fin Heat Exchanger," Energies, MDPI, vol. 11(6), pages 1-18, May.
    6. Heng Chen & Yungang Wang & Qinxin Zhao & Haidong Ma & Yuxin Li & Zhongya Chen, 2014. "Experimental Investigation of Heat Transfer and Pressure Drop Characteristics of H-type Finned Tube Banks," Energies, MDPI, vol. 7(11), pages 1-11, November.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Shehryar Ishaque & Man-Hoe Kim, 2019. "Seasonal Performance Investigation for Residential Heat Pump System with Different Outdoor Heat Exchanger Designs," Energies, MDPI, vol. 12(24), pages 1-22, December.
    2. Sadeghianjahromi, Ali & Wang, Chi-Chuan, 2021. "Heat transfer enhancement in fin-and-tube heat exchangers – A review on different mechanisms," Renewable and Sustainable Energy Reviews, Elsevier, vol. 137(C).
    3. Wan-Ling Hu & Ai-Jun Ma & Yong Guan & Zhi-Jie Cui & Yi-Bo Zhang & Jing Wang, 2021. "Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions," Energies, MDPI, vol. 14(21), pages 1-15, October.
    4. Mustansar Hayat Saggu & Nadeem Ahmed Sheikh & Usama Muhammad Niazi & Muhammad Irfan & Adam Glowacz, 2020. "Predicting the Structural Reliability of LNG Processing Plate-Fin Heat Exchanger for Energy Conservation," Energies, MDPI, vol. 13(9), pages 1-22, May.
    5. Hyung Ju Lee & Jaiyoung Ryu & Seong Hyuk Lee, 2019. "Influence of Perforated Fin on Flow Characteristics and Thermal Performance in Spiral Finned-Tube Heat Exchanger," Energies, MDPI, vol. 12(3), pages 1-13, February.
    6. Jingang Yang & Yaohua Zhao & Aoxue Chen & Zhenhua Quan, 2019. "Thermal Performance of a Low-Temperature Heat Exchanger Using a Micro Heat Pipe Array," Energies, MDPI, vol. 12(4), pages 1-16, February.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Jingang Yang & Yaohua Zhao & Aoxue Chen & Zhenhua Quan, 2019. "Thermal Performance of a Low-Temperature Heat Exchanger Using a Micro Heat Pipe Array," Energies, MDPI, vol. 12(4), pages 1-16, February.
    2. Azeez mohammed Hussein, Hind & Zulkifli, Rozli & Faizal Bin Wan Mahmood, Wan Mohd & Ajeel, Raheem K., 2022. "Structure parameters and designs and their impact on performance of different heat exchangers: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    3. Mustansar Hayat Saggu & Nadeem Ahmed Sheikh & Usama Muhammad Niazi & Muhammad Irfan & Adam Glowacz, 2020. "Predicting the Structural Reliability of LNG Processing Plate-Fin Heat Exchanger for Energy Conservation," Energies, MDPI, vol. 13(9), pages 1-22, May.
    4. Shehryar Ishaque & Man-Hoe Kim, 2019. "Seasonal Performance Investigation for Residential Heat Pump System with Different Outdoor Heat Exchanger Designs," Energies, MDPI, vol. 12(24), pages 1-22, December.
    5. Ryo Arai & Satoru Sakai & Akihiro Tatsuoka & Qin Zhang, 2021. "Analytical, Experimental, and Numerical Investigation of Energy in Hydraulic Cylinder Dynamics of Agriculture Scale Excavators," Energies, MDPI, vol. 14(19), pages 1-20, September.
    6. Xiang Peng & Denghong Li & Jiquan Li & Shaofei Jiang & Qilong Gao, 2020. "Improvement of Flow Distribution by New Inlet Header Configuration with Splitter Plates for Plate-Fin Heat Exchanger," Energies, MDPI, vol. 13(6), pages 1-14, March.
    7. Shahsavar, Amin & Al-Rashed, Abdullah A.A.A. & Entezari, Sajad & Sardari, Pouyan Talebizadeh, 2019. "Melting and solidification characteristics of a double-pipe latent heat storage system with sinusoidal wavy channels embedded in a porous medium," Energy, Elsevier, vol. 171(C), pages 751-769.
    8. Tang, Song-Zhen & Wang, Fei-Long & He, Ya-Ling & Yu, Yang & Tong, Zi-Xiang, 2019. "Parametric optimization of H-type finned tube with longitudinal vortex generators by response surface model and genetic algorithm," Applied Energy, Elsevier, vol. 239(C), pages 908-918.
    9. Ko, Yun Mo & Song, Joo Young & Lee, Jae Won & Sohn, Sangho & Song, Chan Ho & Khoshvaght-Aliabadi, Morteza & Kim, Yongchan & Kang, Yong Tae, 2024. "A critical review on Colburn j-factor and f-factor and energy performance analysis for finned tube heat exchangers," Energy, Elsevier, vol. 287(C).
    10. Agung Tri Wijayanta & Pranowo & Mirmanto & Budi Kristiawan & Muhammad Aziz, 2019. "Internal Flow in an Enhanced Tube Having Square-cut Twisted Tape Insert," Energies, MDPI, vol. 12(2), pages 1-12, January.
    11. Gan Liu & Chen Yang & Junhui Zhang & Huaizhi Zong & Bing Xu & Jin-yuan Qian, 2020. "Internal Flow Analysis of a Heat Transfer Enhanced Tube with a Segmented Twisted Tape Insert," Energies, MDPI, vol. 13(1), pages 1-16, January.
    12. Zhao, Xiaohuan & E, Jiaqiang & Zhang, Zhiqing & Chen, Jingwei & Liao, Gaoliang & Zhang, Feng & Leng, Erwei & Han, Dandan & Hu, Wenyu, 2020. "A review on heat enhancement in thermal energy conversion and management using Field Synergy Principle," Applied Energy, Elsevier, vol. 257(C).
    13. Lei Chai & Savvas A. Tassou, 2018. "A Review of Airside Heat Transfer Augmentation with Vortex Generators on Heat Transfer Surface," Energies, MDPI, vol. 11(10), pages 1-45, October.
    14. Yerzhan Asem Anuarkyzy & Marat B. Koshumbaev, 2016. "New Design of Low-Head Hydro Turbine for Small-Scale Hydropower Plant," International Journal of Technology and Engineering Studies, PROF.IR.DR.Mohid Jailani Mohd Nor, vol. 2(3), pages 87-94.
    15. Agung Tri Wijayanta & Muhammad Aziz & Keishi Kariya & Akio Miyara, 2018. "Numerical Study of Heat Transfer Enhancement of Internal Flow Using Double-Sided Delta-Winglet Tape Insert," Energies, MDPI, vol. 11(11), pages 1-15, November.
    16. Qinghong Peng & Qungui Du, 2016. "Progress in Heat Pump Air Conditioning Systems for Electric Vehicles—A Review," Energies, MDPI, vol. 9(4), pages 1-17, March.
    17. Bożena Babiarz & Władysław Szymański, 2020. "Introduction to the Dynamics of Heat Transfer in Buildings," Energies, MDPI, vol. 13(23), pages 1-28, December.
    18. Pradhyumn Bhale & Mrinal Kaushik & Jane-Sunn Liaw & Chi-Chuan Wang, 2019. "Airside Performance of H-Type Finned Tube Banks with Surface Modifications," Energies, MDPI, vol. 12(4), pages 1-16, February.
    19. Arslan Saleem & Man-Hoe Kim, 2022. "Airside Thermal Performance of Louvered Fin Flat-Tube Heat Exchangers with Different Redirection Louvers," Energies, MDPI, vol. 15(16), pages 1-21, August.
    20. Choi, Seok Min & Kwon, Hyun Goo & Kim, Taehyun & Moon, Hee Koo & Cho, Hyung Hee, 2022. "Active cooling of photovoltaic (PV) cell by acoustic excitation in single-dimpled internal channel," Applied Energy, Elsevier, vol. 309(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:11:y:2018:i:8:p:1959-:d:160452. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.