IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v13y2020i9p2175-d352986.html
   My bibliography  Save this article

Predicting the Structural Reliability of LNG Processing Plate-Fin Heat Exchanger for Energy Conservation

Author

Listed:
  • Mustansar Hayat Saggu

    (Department of Mechanical Engineering, International Islamic University, Islamabad 44000, Pakistan)

  • Nadeem Ahmed Sheikh

    (Department of Mechanical Engineering, International Islamic University, Islamabad 44000, Pakistan)

  • Usama Muhammad Niazi

    (Mechanical Engineering Department, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Malaysia)

  • Muhammad Irfan

    (Electrical Engineering Department, Najran University, Najran 61441, Saudi Arabia)

  • Adam Glowacz

    (Department of Automatic, Control and Robotics, AGH University of Science and Technology, 30-059 Kraków, Poland)

Abstract

Liquefied natural gas (LNG) is one of the hydrocarbon fuels with the least carbon footprint having a rapidly rising global share in the prime energy market. LNG processing for transportation at longer distances works under cryogenic conditions, especially when used for liquefaction and gasification applications. The supply chain of the eco-environmental friendly hydrocarbon is heavily dependent on the processing plant used for liquefaction and subsequent re-gasification of the natural gas. Plate-fin heat exchangers are extensively used in the LNG industry for both re-gasification as well as liquefaction processes. The exchange of heat during the process of natural gas phase change involves plate-fin heat exchangers working under cryogenic low-temperature conditions. The heat exchangers are designed to have brazed joints that are most vulnerable to failure under these temperature conditions. One failure of such a joint can not only hinder the supply chain but also may result in fire and life hazards. In almost all earlier studies, analytical and numerical methods were used to analyze these braze joints using finite element method methods and examining the stresses while keeping them at or near to ambient conditions. In this research, the plate-fin heat exchanger is investigated for its structural stability of brazed fins for three different fin configurations: plain, wavy and compound having different joint geometries. In addition, the analyses are carried out using experimentally measured brazed joint strength which is measured to be on average 22% lower than the base material strength owing to brazing process and resultant heat-affected zone (HAZ). Therefore, the reliability is assessed for these joints in terms of factor of safety (FOS) while keeping in view the actual yield criteria. It was found that the structural stability of compound fins configuration is weakest amongst all considered fin configurations. The failure of the compound fin brazed joint is expected to be along the horizontal path of the joint due to yielding. The study also predicts the life of the fin brazed joints in different joining directions with different topologies of fins commonly recommended in the literature. It is observed that the commonly recommended safe fin geometries are predicted to be susceptible to failure if a reduction in the brazed joint is considered. The analysis and recommendation in this paper shall provide a reliable and safe design approach for plate-fin exchangers for different operating conditions especially in low to cryogenic temperature applications.

Suggested Citation

  • Mustansar Hayat Saggu & Nadeem Ahmed Sheikh & Usama Muhammad Niazi & Muhammad Irfan & Adam Glowacz, 2020. "Predicting the Structural Reliability of LNG Processing Plate-Fin Heat Exchanger for Energy Conservation," Energies, MDPI, vol. 13(9), pages 1-22, May.
  • Handle: RePEc:gam:jeners:v:13:y:2020:i:9:p:2175-:d:352986
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/13/9/2175/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/13/9/2175/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Ali Sadeghianjahromi & Saeid Kheradmand & Hossain Nemati & Jane-Sunn Liaw & Chi-Chuan Wang, 2018. "Compound Heat Transfer Enhancement of Wavy Fin-and-Tube Heat Exchangers through Boundary Layer Restarting and Swirled Flow," Energies, MDPI, vol. 11(8), pages 1-19, July.
    2. Moo-Yeon Lee & Yongchan Kim & Dong-Yeon Lee, 2012. "Experimental Study on Frost Height of Round Plate Fin-Tube Heat Exchangers for Mobile Heat Pumps," Energies, MDPI, vol. 5(9), pages 1-13, September.
    3. Yuan Xue & Zhihua Ge & Xiaoze Du & Lijun Yang, 2018. "On the Heat Transfer Enhancement of Plate Fin Heat Exchanger," Energies, MDPI, vol. 11(6), pages 1-18, May.
    4. Xiang Peng & Denghong Li & Jiquan Li & Shaofei Jiang & Qilong Gao, 2020. "Improvement of Flow Distribution by New Inlet Header Configuration with Splitter Plates for Plate-Fin Heat Exchanger," Energies, MDPI, vol. 13(6), pages 1-14, March.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Mustansar Hayat Saggu & Nadeem Ahmed Sheikh & Usama Muhamad Niazi & Muhammad Irfan & Adam Glowacz & Stanislaw Legutko, 2020. "Improved Analysis on the Fin Reliability of a Plate Fin Heat Exchanger for Usage in LNG Applications," Energies, MDPI, vol. 13(14), pages 1-16, July.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Jingang Yang & Yaohua Zhao & Aoxue Chen & Zhenhua Quan, 2019. "Thermal Performance of a Low-Temperature Heat Exchanger Using a Micro Heat Pipe Array," Energies, MDPI, vol. 12(4), pages 1-16, February.
    2. Ali Sadeghianjahromi & Saeid Kheradmand & Hossain Nemati & Jane-Sunn Liaw & Chi-Chuan Wang, 2018. "Compound Heat Transfer Enhancement of Wavy Fin-and-Tube Heat Exchangers through Boundary Layer Restarting and Swirled Flow," Energies, MDPI, vol. 11(8), pages 1-19, July.
    3. Azeez mohammed Hussein, Hind & Zulkifli, Rozli & Faizal Bin Wan Mahmood, Wan Mohd & Ajeel, Raheem K., 2022. "Structure parameters and designs and their impact on performance of different heat exchangers: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    4. Xiang Peng & Denghong Li & Jiquan Li & Shaofei Jiang & Qilong Gao, 2020. "Improvement of Flow Distribution by New Inlet Header Configuration with Splitter Plates for Plate-Fin Heat Exchanger," Energies, MDPI, vol. 13(6), pages 1-14, March.
    5. Natalia Rydalina & Elena Antonova & Irina Akhmetova & Svetlana Ilyashenko & Olga Afanaseva & Vincenzo Bianco & Alexander Fedyukhin, 2020. "Analysis of the Efficiency of Using Heat Exchangers with Porous Inserts in Heat and Gas Supply Systems," Energies, MDPI, vol. 13(22), pages 1-13, November.
    6. Agung Tri Wijayanta & Pranowo & Mirmanto & Budi Kristiawan & Muhammad Aziz, 2019. "Internal Flow in an Enhanced Tube Having Square-cut Twisted Tape Insert," Energies, MDPI, vol. 12(2), pages 1-12, January.
    7. Gan Liu & Chen Yang & Junhui Zhang & Huaizhi Zong & Bing Xu & Jin-yuan Qian, 2020. "Internal Flow Analysis of a Heat Transfer Enhanced Tube with a Segmented Twisted Tape Insert," Energies, MDPI, vol. 13(1), pages 1-16, January.
    8. Kyung Rae Kim & Jae Keun Lee & Hae Do Jeong & Yul Ho Kang & Young Chull Ahn, 2020. "Numerical and Experimental Study of Air-to-Air Plate Heat Exchangers with Plain and Offset Strip Fin Shapes," Energies, MDPI, vol. 13(21), pages 1-13, October.
    9. Agung Tri Wijayanta & Muhammad Aziz & Keishi Kariya & Akio Miyara, 2018. "Numerical Study of Heat Transfer Enhancement of Internal Flow Using Double-Sided Delta-Winglet Tape Insert," Energies, MDPI, vol. 11(11), pages 1-15, November.
    10. Qinghong Peng & Qungui Du, 2016. "Progress in Heat Pump Air Conditioning Systems for Electric Vehicles—A Review," Energies, MDPI, vol. 9(4), pages 1-17, March.
    11. Bożena Babiarz & Władysław Szymański, 2020. "Introduction to the Dynamics of Heat Transfer in Buildings," Energies, MDPI, vol. 13(23), pages 1-28, December.
    12. Mingkan Zhang & Cheng-Min Yang & Kai Li & Kashif Nawaz, 2023. "Reducing the Flow Maldistribution in Heat Exchangers through a Novel Polymer Manifold: Numerical Evaluation," Energies, MDPI, vol. 16(20), pages 1-15, October.
    13. Jianying Gong & Jianqiang Hou & Jinjuan Sun & Guojun Li & Tieyu Gao, 2018. "A Numerical Investigation of Frost Growth on Cold Surfaces Based on the Lattice Boltzmann Method," Energies, MDPI, vol. 11(8), pages 1-13, August.
    14. Wan-Ling Hu & Ai-Jun Ma & Yong Guan & Zhi-Jie Cui & Yi-Bo Zhang & Jing Wang, 2021. "Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions," Energies, MDPI, vol. 14(21), pages 1-15, October.
    15. Hyung Ju Lee & Jaiyoung Ryu & Seong Hyuk Lee, 2019. "Influence of Perforated Fin on Flow Characteristics and Thermal Performance in Spiral Finned-Tube Heat Exchanger," Energies, MDPI, vol. 12(3), pages 1-13, February.
    16. Yao, Ling & Wang, Feng & Wang, Long & Wang, Guoqiang, 2019. "Transport enhancement study on small-scale methanol steam reforming reactor with waste heat recovery for hydrogen production," Energy, Elsevier, vol. 175(C), pages 986-997.
    17. Sadeghianjahromi, Ali & Wang, Chi-Chuan, 2021. "Heat transfer enhancement in fin-and-tube heat exchangers – A review on different mechanisms," Renewable and Sustainable Energy Reviews, Elsevier, vol. 137(C).
    18. Shehryar Ishaque & Man-Hoe Kim, 2019. "Seasonal Performance Investigation for Residential Heat Pump System with Different Outdoor Heat Exchanger Designs," Energies, MDPI, vol. 12(24), pages 1-22, December.
    19. Mustansar Hayat Saggu & Nadeem Ahmed Sheikh & Usama Muhamad Niazi & Muhammad Irfan & Adam Glowacz & Stanislaw Legutko, 2020. "Improved Analysis on the Fin Reliability of a Plate Fin Heat Exchanger for Usage in LNG Applications," Energies, MDPI, vol. 13(14), pages 1-16, July.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:13:y:2020:i:9:p:2175-:d:352986. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.