IDEAS home Printed from https://ideas.repec.org/a/gam/jcltec/v3y2021i2p26-461d562657.html
   My bibliography  Save this article

Impact of Pyrolysis Oil Addition to Ethanol on Combustion in the Internal Combustion Spark Ignition Engine

Author

Listed:
  • Magdalena Szwaja

    (Faculty of Mechanical Engineering and Computer Science, Czestochowa University of Technology, 21 Armii Krajowej St., 42-200 Czestochowa, Poland)

  • Mariusz Chwist

    (Faculty of Mechanical Engineering and Computer Science, Czestochowa University of Technology, 21 Armii Krajowej St., 42-200 Czestochowa, Poland)

  • Stanislaw Szwaja

    (Faculty of Mechanical Engineering and Computer Science, Czestochowa University of Technology, 21 Armii Krajowej St., 42-200 Czestochowa, Poland)

  • Romualdas Juknelevičius

    (Faculty of Mechanics, Vilnius Gediminas Technical University, J. Basanavicius str. 28, 03224 Vilnius, Lithuania)

Abstract

Thermal processing (torrefaction, pyrolysis, and gasification), as a technology can provide environmentally friendly use of plastic waste. However, it faces a problem with respect to its by-products. Pyrolysis oil obtained using this technology is seen as a substance that is extremely harmful for living creatures and that needs to be neutralized. Due to its relatively high calorific value, it can be considered as a potential fuel for internal combustion spark-ignition engines. In order make the combustion process effective, pyrolysis oil is blended with ethanol, which is commonly used as a fuel for flexible fuel cars. This article presents results from combustion tests conducted on a single-cylinder research engine at full load working at 600 rpm at a compression ratio of 9.5:1, and an equivalence ratio of 1. The analysis showed improvements in combustion and engine performance. It was found that, due to the higher calorific value of the blend, the engine possessed a higher indicated mean effective pressure. It was also found that optimal spark timing for this ethanol-pyrolysis oil blend was improved at a crank angle of 2–3° at 600 rpm. In summary, ethanol-pyrolysis oil blends at a volumetric ratio of 3:1 (25% pyrolysis oil) can successfully substitute ethanol in spark-ignition engines, particularly for vehicles with flexible fuel type.

Suggested Citation

  • Magdalena Szwaja & Mariusz Chwist & Stanislaw Szwaja & Romualdas Juknelevičius, 2021. "Impact of Pyrolysis Oil Addition to Ethanol on Combustion in the Internal Combustion Spark Ignition Engine," Clean Technol., MDPI, vol. 3(2), pages 1-12, May.
    • Handle: RePEc:gam:jcltec:v:3:y:2021:i:2:p:26-461:d:562657
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2571-8797/3/2/26/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/2571-8797/3/2/26/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Kumaravel, S.T. & Murugesan, A. & Kumaravel, A., 2016. "Tyre pyrolysis oil as an alternative fuel for diesel engines – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 60(C), pages 1678-1685.
    2. Krutof, Anke & Hawboldt, Kelly, 2016. "Blends of pyrolysis oil, petroleum, and other bio-based fuels: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 59(C), pages 406-419.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Szwaja, Magdalena & Chwist, Mariusz & Szymanek, Arkadiusz & Szwaja, Stanisław, 2022. "Pyrolysis oil blended n-butanol as a fuel for power generation by an internal combustion engine," Energy, Elsevier, vol. 261(PB).
    2. Jacek Caban & Jan Vrabel & Dorota Górnicka & Radosław Nowak & Maciej Jankiewicz & Jonas Matijošius & Marek Palka, 2023. "Overview of Energy Harvesting Technologies Used in Road Vehicles," Energies, MDPI, vol. 16(9), pages 1-32, April.
    3. Magdalena Szwaja & Jeffrey D. Naber & David Shonnard & Daniel Kulas & Ali Zolghadr & Stanislaw Szwaja, 2022. "Comparative Analysis of Injection of Pyrolysis Oil from Plastics and Gasoline into the Engine Cylinder and Atomization by a Direct High-Pressure Injector," Energies, MDPI, vol. 16(1), pages 1-11, December.
    4. Jančauskas, Adolfas & Striūgas, Nerijus & Zakarauskas, Kęstutis & Skvorčinskienė, Raminta & Eimontas, Justinas & Buinevičius, Kęstutis, 2024. "Experimental investigation of sorted municipal solid wastes producer gas composition in an updraft fixed bed gasifier," Energy, Elsevier, vol. 289(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Naqvi, Salman Raza & Jamshaid, Sana & Naqvi, Muhammad & Farooq, Wasif & Niazi, Muhammad Bilal Khan & Aman, Zaeem & Zubair, Muhammad & Ali, Majid & Shahbaz, Muhammad & Inayat, Abrar & Afzal, Waheed, 2018. "Potential of biomass for bioenergy in Pakistan based on present case and future perspectives," Renewable and Sustainable Energy Reviews, Elsevier, vol. 81(P1), pages 1247-1258.
    2. Goel, Varun & Kumar, Naresh & Singh, Paramvir, 2018. "Impact of modified parameters on diesel engine characteristics using biodiesel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 2716-2729.
    3. Leng, Lijian & Li, Hui & Yuan, Xingzhong & Zhou, Wenguang & Huang, Huajun, 2018. "Bio-oil upgrading by emulsification/microemulsification: A review," Energy, Elsevier, vol. 161(C), pages 214-232.
    4. Kasmuri, N.H. & Kamarudin, S.K. & Abdullah, S.R.S. & Hasan, H.A. & Som, A.Md., 2017. "Process system engineering aspect of bio-alcohol fuel production from biomass via pyrolysis: An overview," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 914-923.
    5. Qi, D.H. & Yang, K. & Zhang, D. & Chen, B. & Wei, Q. & Zhang, C.H., 2017. "Experimental investigation of a turbocharged CRDI diesel engine fueled with Tung oil-diesel-ethanol microemulsion fuel," Renewable Energy, Elsevier, vol. 113(C), pages 1201-1207.
    6. Chintala, Venkateswarlu, 2018. "Production, upgradation and utilization of solar assisted pyrolysis fuels from biomass – A technical review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 90(C), pages 120-130.
    7. Varun, & Singh, Paramvir & Tiwari, Samaresh Kumar & Singh, Rituparn & Kumar, Naresh, 2017. "Modification in combustion chamber geometry of CI engines for suitability of biodiesel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 1016-1033.
    8. Li, Dan & Lei, Shijun & Rajput, Gulzeb & Zhong, Lei & Ma, Wenchao & Chen, Guanyi, 2021. "Study on the co-pyrolysis of waste tires and plastics," Energy, Elsevier, vol. 226(C).
    9. Shahbaz, Muhammad & Al-Ansari, Tareq & Inayat, Muddasser & Sulaiman, Shaharin A. & Parthasarathy, Prakash & McKay, Gordon, 2020. "A critical review on the influence of process parameters in catalytic co-gasification: Current performance and challenges for a future prospectus," Renewable and Sustainable Energy Reviews, Elsevier, vol. 134(C).
    10. Ribeiro, Luiz Augusto Badan & Martins, Robson Cristiano & Mesa-Pérez, Juan Miguel & Bizzo, Waldir Antonio, 2019. "Study of bio-oil properties and ageing through fractionation and ternary mixtures with the heavy fraction as the main component," Energy, Elsevier, vol. 169(C), pages 344-355.
    11. Jiří Bojanovský & Vítězslav Máša & Igor Hudák & Pavel Skryja & Josef Hopjan, 2022. "Rotary Kiln, a Unit on the Border of the Process and Energy Industry—Current State and Perspectives," Sustainability, MDPI, vol. 14(21), pages 1-34, October.
    12. Li, Dan & Lei, Shijun & Lin, Fawei & Zhong, Lei & Ma, Wenchao & Chen, Guanyi, 2020. "Study of scrap tires pyrolysis – Products distribution and mechanism," Energy, Elsevier, vol. 213(C).
    13. Toscano Miranda, Nahieh & Lopes Motta, Ingrid & Maciel Filho, Rubens & Wolf Maciel, Maria Regina, 2021. "Sugarcane bagasse pyrolysis: A review of operating conditions and products properties," Renewable and Sustainable Energy Reviews, Elsevier, vol. 149(C).
    14. Choi, Gyung-Goo & Oh, Seung-Jin & Kim, Joo-Sik, 2017. "Clean pyrolysis oil from a continuous two-stage pyrolysis of scrap tires using in-situ and ex-situ desulfurization," Energy, Elsevier, vol. 141(C), pages 2234-2241.
    15. Mishra, Asmita & Siddiqi, Hammad & Kumari, Usha & Behera, Ipsita Dipamitra & Mukherjee, Subhrajit & Meikap, B.C., 2021. "Pyrolysis of waste lubricating oil/waste motor oil to generate high-grade fuel oil: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 150(C).
    16. Yu, Jie & Liu, Sheng & Cardoso, Aderlanio & Han, Yang & Bikane, Kagiso & Sun, Lushi, 2019. "Catalytic pyrolysis of rubbers and vulcanized rubbers using modified zeolites and mesoporous catalysts with Zn and Cu," Energy, Elsevier, vol. 188(C).
    17. Lin, Bo-Jhih & Chen, Wei-Hsin & Hsieh, Tzu-Hsien & Ong, Hwai Chyuan & Show, Pau Loke & Naqvi, Salman Raza, 2019. "Oxidative reaction interaction and synergistic index of emulsified pyrolysis bio-oil/diesel fuels," Renewable Energy, Elsevier, vol. 136(C), pages 223-234.
    18. Jena, Priyaranjan & Raj, Reetu & Tirkey, Jeewan Vachan, 2023. "Thermodynamic performance study and RSM based optimization of SI engine using sewage sludge producer gas blend with methane," Energy, Elsevier, vol. 273(C).
    19. Ochoa, Aitor & Vicente, Héctor & Sierra, Irene & Arandes, José M. & Castaño, Pedro, 2020. "Implications of feeding or cofeeding bio-oil in the fluid catalytic cracker (FCC) in terms of regeneration kinetics and energy balance," Energy, Elsevier, vol. 209(C).
    20. Zhang, Jiehan & Wang, Xinkun & Chen, Zhaohui & Zhang, Xinyu & Yue, Junrong & Zhou, Ridong & Lai, Dengguo & Yu, Jian & Li, Jianling & Xu, Guangwen, 2024. "Regulation of volatile reactions through thermal/catalytic cracking during scrap tires pyrolysis for high-valued chemicals production," Energy, Elsevier, vol. 294(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jcltec:v:3:y:2021:i:2:p:26-461:d:562657. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.