IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v251y2022ics0360544222008647.html
   My bibliography  Save this article

Design optimization of an additively manufactured prototype recuperator for supercritical CO2 power cycles

Author

Listed:
  • Robey, Ed
  • Ramesh, Sridharan
  • Sabau, Adrian S.
  • Abdoli, Abas
  • Black, James
  • Straub, Doug
  • Yip, Joe

Abstract

Supercritical CO2 (sCO2) power cycles are being developed due to their potential for high efficiency and reduced capital cost. It is necessary that these recuperators operate at high pressures and temperatures, up to 30 MPa and 900 K, with effectiveness values > 95% and pressure drops <1% to achieve high cycle efficiencies. Moreover, it is also necessary to have reasonable cost recuperators to control the capital costs of the sCO2 power cycles. In this study, a Plate Pin-Fin (PPF) heat exchanger has been proposed as an sCO2 recuperator. This preliminary recuperator design leverages capabilities enabled by additive manufacturing. Although the PPF design has characteristics similar to those of a plate heat exchanger, small diameter and relatively long fins are used to increase surface area, enhance heat transfer, and provide structural support for the partition plates that separate the fluid streams. Existing correlations for heat transfer and pressure drop were adapted for the PPF heat exchanger. These correlations were implemented in a 1D analytical model and used for the optimization of a 5-kWth high temperature recuperator for an indirect sCO2 cycle by varying the design parameters to minimize the quantity of material required. A 3D conjugate heat transfer numerical simulations were conducted to validate the heat transfer and pressure loss correlations. A steepest descent method was used to minimize heat exchanger mass for a 5-kW prototype recuperator subject to a maximum specified pressure drop. The design analysis indicated that an optimum PPF recuperator would be attained for the minimum allowable pin transverse spacing, minimum pin width, minimum pin height and near maximum cell aspect ratio. At a low material requirement of 0.216 kg/kW and a pressure drop, which is almost five times lower than the allowable pressure drop design target, the optimized PPF heat exchanger has the high potential to be an alternative to a printed circuit heat exchanger, which is a conservative design basis for the current state-of-the-art sCO2 recuperators.

Suggested Citation

  • Robey, Ed & Ramesh, Sridharan & Sabau, Adrian S. & Abdoli, Abas & Black, James & Straub, Doug & Yip, Joe, 2022. "Design optimization of an additively manufactured prototype recuperator for supercritical CO2 power cycles," Energy, Elsevier, vol. 251(C).
  • Handle: RePEc:eee:energy:v:251:y:2022:i:c:s0360544222008647
    DOI: 10.1016/j.energy.2022.123961
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544222008647
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.energy.2022.123961?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Jiang, Yuan & Liese, Eric & Zitney, Stephen E. & Bhattacharyya, Debangsu, 2018. "Optimal design of microtube recuperators for an indirect supercritical carbon dioxide recompression closed Brayton cycle," Applied Energy, Elsevier, vol. 216(C), pages 634-648.
    2. Jiang, Yuan & Liese, Eric & Zitney, Stephen E. & Bhattacharyya, Debangsu, 2018. "Design and dynamic modeling of printed circuit heat exchangers for supercritical carbon dioxide Brayton power cycles," Applied Energy, Elsevier, vol. 231(C), pages 1019-1032.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Dang, Chaolei & Cheng, Kunlin & Fan, Junhao & Wang, Yilin & Qin, Jiang & Liu, Guodong, 2023. "Performance analysis of fuel vapor turbine and closed-Brayton-cycle combined power generation system for hypersonic vehicles," Energy, Elsevier, vol. 266(C).
    2. Li, Zhen & Lu, Daogang & Wang, Zhichao & Cao, Qiong, 2023. "Analysis on flow and heat transfer performance of SCO2 in airfoil channels with different fin angles of attack," Energy, Elsevier, vol. 282(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Yao, Lichao & Zou, Zhengping, 2020. "A one-dimensional design methodology for supercritical carbon dioxide Brayton cycles: Integration of cycle conceptual design and components preliminary design," Applied Energy, Elsevier, vol. 276(C).
    2. Liu, Guangxu & Huang, Yanping & Wang, Junfeng & Liu, Ruilong, 2020. "A review on the thermal-hydraulic performance and optimization of printed circuit heat exchangers for supercritical CO2 in advanced nuclear power systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 133(C).
    3. Edwin Espinel Blanco & Guillermo Valencia Ochoa & Jorge Duarte Forero, 2020. "Thermodynamic, Exergy and Environmental Impact Assessment of S-CO 2 Brayton Cycle Coupled with ORC as Bottoming Cycle," Energies, MDPI, vol. 13(9), pages 1-24, May.
    4. Zhou, Aozheng & Li, Xue-song & Ren, Xiao-dong & Song, Jian & Gu, Chun-wei, 2020. "Thermodynamic and economic analysis of a supercritical carbon dioxide (S–CO2) recompression cycle with the radial-inflow turbine efficiency prediction," Energy, Elsevier, vol. 191(C).
    5. Thanganadar, Dhinesh & Fornarelli, Francesco & Camporeale, Sergio & Asfand, Faisal & Patchigolla, Kumar, 2021. "Off-design and annual performance analysis of supercritical carbon dioxide cycle with thermal storage for CSP application," Applied Energy, Elsevier, vol. 282(PA).
    6. Dora Villada-Castillo & Guillermo Valencia-Ochoa & Jorge Duarte-Forero, 2023. "Thermohydraulic and Economic Evaluation of a New Design for Printed Circuit Heat Exchangers in Supercritical CO 2 Brayton Cycle," Energies, MDPI, vol. 16(5), pages 1-24, February.
    7. Zhou, Aozheng & Li, Xue-song & Ren, Xiao-dong & Gu, Chun-wei, 2020. "Improvement design and analysis of a supercritical CO2/transcritical CO2 combined cycle for offshore gas turbine waste heat recovery," Energy, Elsevier, vol. 210(C).
    8. Ma, Teng & Li, Ming-Jia & Xu, Jin-Liang & Cao, Feng, 2019. "Thermodynamic analysis and performance prediction on dynamic response characteristic of PCHE in 1000 MW S-CO2 coal fired power plant," Energy, Elsevier, vol. 175(C), pages 123-138.
    9. Ma, Teng & Li, Ming-Jia & Xu, Hang, 2024. "Thermal energy storage capacity configuration and energy distribution scheme for a 1000MWe S–CO2 coal-fired power plant to realize high-efficiency full-load adjustability," Energy, Elsevier, vol. 294(C).
    10. Deng, Tianrui & Li, Xionghui & Wang, Qiuwang & Ma, Ting, 2019. "Dynamic modelling and transient characteristics of supercritical CO2 recompression Brayton cycle," Energy, Elsevier, vol. 180(C), pages 292-302.
    11. Zhao, Tian & Li, Hang & Li, Xia & Sun, Qing-Han & Fang, Xuan-Yi & Ma, Huan & Chen, Qun, 2024. "A frequency domain dynamic simulation method for heat exchangers and thermal systems," Energy, Elsevier, vol. 286(C).
    12. Xu, Zhen & Liu, Xinxin & Xie, Yingchun, 2023. "Off-design performances of a dry-cooled supercritical recompression Brayton cycle using CO2–H2S as working fluid," Energy, Elsevier, vol. 276(C).
    13. Zhang, Lianjie & Deng, Tianrui & Klemeš, Jiří Jaromír & Zeng, Min & Ma, Ting & Wang, Qiuwang, 2021. "Supercritical CO2 Brayton cycle at different heat source temperatures and its analysis under leakage and disturbance conditions," Energy, Elsevier, vol. 237(C).
    14. Wan, Yuke & Wu, Chuang & Liu, Yu & Liu, Chao & Li, Hang & Wang, Jiangfeng, 2023. "A technical feasibility study of a liquid carbon dioxide energy storage system: Integrated component design and off-design performance analysis," Applied Energy, Elsevier, vol. 350(C).
    15. Du, Yadong & Hu, Chenxing & Yang, Ce & Wang, Haimei & Dong, Wuqiang, 2022. "Size optimization of heat exchanger and thermoeconomic assessment for supercritical CO2 recompression Brayton cycle applied in marine," Energy, Elsevier, vol. 239(PD).
    16. Bian, Xingyan & Wang, Xuan & Wang, Rui & Cai, Jinwen & Tian, Hua & Shu, Gequn & Lin, Zhimin & Yu, Xiangyu & Shi, Lingfeng, 2022. "A comprehensive evaluation of the effect of different control valves on the dynamic performance of a recompression supercritical CO2 Brayton cycle," Energy, Elsevier, vol. 248(C).
    17. He, Tianyu & Cao, Yue & Si, Fengqi & Chua, Kian Jon, 2024. "Off-design characteristics and operation strategy analysis of a compressed carbon dioxide energy storage system coupled with a combined heating and power plant," Energy, Elsevier, vol. 303(C).
    18. Pidaparti, Sandeep R. & White, Charles W. & Liese, Eric & Weiland, Nathan T., 2024. "Performance and cost potential for direct-fired supercritical CO2 natural gas power plants," Energy, Elsevier, vol. 299(C).
    19. Wei Wang & Liang Ding & Fangming Han & Yong Shuai & Bingxi Li & Bengt Sunden, 2022. "Parametric Study on Thermo-Hydraulic Performance of NACA Airfoil Fin PCHEs Channels," Energies, MDPI, vol. 15(14), pages 1-15, July.
    20. Ouyang, Tiancheng & Pan, Mingming & Tan, Xianlin & Li, Lulu & Huang, Youbin & Mo, Chunlan, 2024. "Power prediction and packed bed heat storage control for marine diesel engine waste heat recovery," Applied Energy, Elsevier, vol. 357(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:251:y:2022:i:c:s0360544222008647. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.