IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v11y2019i23p6714-d291347.html
   My bibliography  Save this article

Effect of pH on Rheological and Filtration Properties of Water-Based Drilling Fluid Based on Bentonite

Author

Listed:
  • Hany Gamal

    (Petroleum Department, King Fahd University of Petroleum & Minerals Box 5049, Dhahran 31261, Saudi Arabia)

  • Salaheldin Elkatatny

    (Petroleum Department, King Fahd University of Petroleum & Minerals Box 5049, Dhahran 31261, Saudi Arabia)

  • Salem Basfar

    (Petroleum Department, King Fahd University of Petroleum & Minerals Box 5049, Dhahran 31261, Saudi Arabia)

  • Abdulaziz Al-Majed

    (Petroleum Department, King Fahd University of Petroleum & Minerals Box 5049, Dhahran 31261, Saudi Arabia)

Abstract

The design of drilling fluids is very important for the drilling operation success. The rheological properties play a key role in the performance of the drilling fluid. Therefore, studying the mud rheological properties of the water-based drilling fluid based on bentonite is essential. The main objectives of this study are to address the effect of pH changes on the rheological and filtration properties of the water-based drilling fluid based on bentonite and to provide a recommended pH range for this drilling fluid for a safe and high-performance drilling operation. Different samples of the water-based drilling fluid based on bentonite with different pH values were prepared, and the rheological properties such as plastic viscosity, yield point, and gel strength were measured. After that, the filtration test was performed under 300 psi differential pressure and 200 °F. The pH for the water-based drilling fluid based on bentonite significantly affects the mud rheology. The shear stress and shear rate relation were varying with the change in the pH. Increasing the pH from 8 to 12 resulted in decreasing the plastic viscosity by 53% and the yield point by 82%, respectively. The ratio of yield point / plastic viscosity was 1.4 for pH of 8 while it decreased to 0.5 for a pH of 11 and 12. There was a significant decrease in the gel strength readings by increasing the pH. The filtrate volume and filter cake thickness increased by increasing pH. The filtration volume increased from 9.5 cm 3 to 12.6 cm 3 by increasing the pH from 9 to 12. The filter cake thickness was 2 mm at 9 pH, while it was increased to 3.6 mm for 12 pH. It is recommended from the results to keep the pH of water-based drilling fluid based on bentonite in the range of 9 to 10 as it provides the optimum mud rheological and filtration properties. The findings of this study illustrated that keeping the pH in the range of 9 to 10 will reduce the plastic viscosity that will help in increasing the rate of penetration and reducing the required pump pressure to circulate the mud to the surface which will help to sustain the drilling operation. In addition, reducing the filtrate volume will produce a thin filter cake which will help in avoiding the pipe sticking and protect the environment. In general, optimizing the pH of the water-based drilling fluid based on bentonite in the range of 9 to 10 will improve the drilling operation and minimize the total cost.

Suggested Citation

  • Hany Gamal & Salaheldin Elkatatny & Salem Basfar & Abdulaziz Al-Majed, 2019. "Effect of pH on Rheological and Filtration Properties of Water-Based Drilling Fluid Based on Bentonite," Sustainability, MDPI, vol. 11(23), pages 1-13, November.
    • Handle: RePEc:gam:jsusta:v:11:y:2019:i:23:p:6714-:d:291347
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/11/23/6714/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/2071-1050/11/23/6714/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Zisis Vryzas & Vassilios C. Kelessidis, 2017. "Nano-Based Drilling Fluids: A Review," Energies, MDPI, vol. 10(4), pages 1-34, April.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Mohammed Al-Rubaii & Mohammed Al-Shargabi & Dhafer Al-Shehri, 2023. "A Novel Model for the Real-Time Evaluation of Hole-Cleaning Conditions with Case Studies," Energies, MDPI, vol. 16(13), pages 1-27, June.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Mikhail A. Sheremet & Hakan F. Oztop & Dmitriy V. Gvozdyakov & Mohamed E. Ali, 2018. "Impacts of Heat-Conducting Solid Wall and Heat-Generating Element on Free Convection of Al 2 O 3 /H 2 O Nanofluid in a Cavity with Open Border," Energies, MDPI, vol. 11(12), pages 1-17, December.
    2. Razali, S.Z. & Yunus, R. & Abdul Rashid, Suraya & Lim, H.N. & Mohamed Jan, B., 2018. "Review of biodegradable synthetic-based drilling fluid: Progression, performance and future prospect," Renewable and Sustainable Energy Reviews, Elsevier, vol. 90(C), pages 171-186.
    3. Pinghe Sun & Junyi Zhu & Binkui Zhao & Xinxin Zhang & Han Cao & Mingjin Tian & Meng Han & Weisheng Liu, 2019. "Study on the Mechanism of Ionic Stabilizers on Shale Gas Reservoir Mechanics in Northwestern Hunan," Energies, MDPI, vol. 12(12), pages 1-11, June.
    4. Jurij Šporin & Tilen Balaško & Primož Mrvar & Blaž Janc & Željko Vukelić, 2020. "Change of the Properties of Steel Material of the Roller Cone Bit Due to the Influence of the Drilling Operational Parameters and Rock Properties," Energies, MDPI, vol. 13(22), pages 1-22, November.
    5. Agostinho C. B. Junior & Raphael R. Silva & Giovanna L. R. Leal & Tarsila M. Tertuliano & Rafael P. Alves & Alfredo I. C. Garnica & Fabiola D. S. Curbelo, 2021. "The Influences of NP100 Surfactant and Pine-Oil Concentrations on Filtrate Volume and Filter-Cake Thickness of Microemulsion-Based Drilling Fluids (O/W)," Energies, MDPI, vol. 14(16), pages 1-15, August.
    6. Shuya Chen & Yanping Shi & Xianyu Yang & Kunzhi Xie & Jihua Cai, 2019. "Design and Evaluation of a Surfactant–Mixed Metal Hydroxide-Based Drilling Fluid for Maintaining Wellbore Stability in Coal Measure Strata," Energies, MDPI, vol. 12(10), pages 1-19, May.
    7. Salaheldin Elkatatny, 2018. "Enhancing the Stability of Invert Emulsion Drilling Fluid for Drilling in High-Pressure High-Temperature Conditions," Energies, MDPI, vol. 11(9), pages 1-15, September.
    8. Alaa Ahmed & Amin Sharifi Haddad & Roozbeh Rafati & Ahmed Bashir & Ahmed M. AlSabagh & Amany A. Aboulrous, 2021. "Developing a Thermally Stable Ester-Based Drilling Fluid for Offshore Drilling Operations by Using Aluminum Oxide Nanorods," Sustainability, MDPI, vol. 13(6), pages 1-18, March.
    9. Omid Mosalman Haghighi & Ghasem Zargar & Abbas Khaksar Manshad & Muhammad Ali & Mohammad Ali Takassi & Jagar A. Ali & Alireza Keshavarz, 2020. "Effect of Environment-Friendly Non-Ionic Surfactant on Interfacial Tension Reduction and Wettability Alteration; Implications for Enhanced Oil Recovery," Energies, MDPI, vol. 13(15), pages 1-18, August.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:11:y:2019:i:23:p:6714-:d:291347. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.