IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v271y2023ics0360544223004942.html
   My bibliography  Save this article

Optimization of melting performance of a heat storage tank under rotation conditions: Based on taguchi design and response surface method

Author

Listed:
  • Huang, Xinyu
  • Li, Fangfei
  • Li, Yuanji
  • Meng, Xiangzhao
  • Yang, Xiaohu
  • Sundén, Bengt

Abstract

The melting performance of a rotating triplex-tube latent heat thermal energy storage unit is studied by numerical simulation method. The Taguchi design and response surface method are applied to its optimized design. Firstly, the Taguchi design method is used to quantitatively reveal the specific effects of fin distribution, fin number, and fin material on the melting performance of the unit. Compared with all-inner tube-fin or all-outer tube-fin structures, the melting time of alternating inside and outside fin structures is shortened by 52.64% and 32.42%, the average heat absorption rate is greatly increased by 105.56% and 47.26%, and the total heat is reduced by 2.64% and 2.17%, respectively. Then, the response surface method is applied to the eight alternating fins obtained by the Taguchi design, and the effects of fin length, width, and rotation angle on the melting time and average heat absorption rate of the unit are studied. Compared with the original structure, the optimal structure reduces the total melting time by 7.37% and increases the average heat absorption rate by 7.23%. The geometric parameters’ interaction with the relevant target response is studied, and the corresponding fluid-structure interaction equation is fitted. Finally, the melt growth phenomenon near the wall is found in the initial melting stage of the optimized model by mechanism analysis.

Suggested Citation

  • Huang, Xinyu & Li, Fangfei & Li, Yuanji & Meng, Xiangzhao & Yang, Xiaohu & Sundén, Bengt, 2023. "Optimization of melting performance of a heat storage tank under rotation conditions: Based on taguchi design and response surface method," Energy, Elsevier, vol. 271(C).
    • Handle: RePEc:eee:energy:v:271:y:2023:i:c:s0360544223004942
    DOI: 10.1016/j.energy.2023.127100
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544223004942
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2023.127100?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Bai, Xiao-Shuai & Yang, Wei-Wei & Tang, Xin-Yuan & Yang, Fu-Sheng & Jiao, Yu-Hang & Yang, Yu, 2021. "Optimization of tree-shaped fin structures towards enhanced absorption performance of metal hydride hydrogen storage device: A numerical study," Energy, Elsevier, vol. 220(C).
    2. Khalil Anwar, M. & Yilbas, B.S. & Shuja, S.Z., 2016. "A thermal battery mimicking a concentrated volumetric solar receiver," Applied Energy, Elsevier, vol. 175(C), pages 16-30.
    3. Costa, Sol Carolina & Kenisarin, Murat, 2022. "A review of metallic materials for latent heat thermal energy storage: Thermophysical properties, applications, and challenges," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    4. Guo, Junfei & Liu, Zhan & Yang, Bo & Yang, Xiaohu & Yan, Jinyue, 2022. "Melting assessment on the angled fin design for a novel latent heat thermal energy storage tube," Renewable Energy, Elsevier, vol. 183(C), pages 406-422.
    5. Feng, Zongbao & Wu, Xianguo & Chen, Hongyu & Qin, Yawei & Zhang, Limao & Skibniewski, Miroslaw J., 2022. "An energy performance contracting parameter optimization method based on the response surface method: A case study of a metro in China," Energy, Elsevier, vol. 248(C).
    6. Mahdi, Jasim M. & Nsofor, Emmanuel C., 2017. "Melting enhancement in triplex-tube latent heat energy storage system using nanoparticles-metal foam combination," Applied Energy, Elsevier, vol. 191(C), pages 22-34.
    7. Huang, Xinyu & Li, Fangfei & Xiao, Tian & Guo, Junfei & Wang, Fan & Gao, Xinyu & Yang, Xiaohu & He, Ya-Ling, 2023. "Investigation and optimization of solidification performance of a triplex-tube latent heat thermal energy storage system by rotational mechanism," Applied Energy, Elsevier, vol. 331(C).
    8. Dhaidan, Nabeel S. & Khodadadi, J.M., 2015. "Melting and convection of phase change materials in different shape containers: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 43(C), pages 449-477.
    9. Huang, Xinyu & Yao, Shouguang & Yang, Xiaohu & Zhou, Rui, 2022. "Melting performance assessments on a triplex-tube thermal energy storage system: Optimization based on response surface method with natural convection," Renewable Energy, Elsevier, vol. 188(C), pages 890-910.
    10. Mahdi, Jasim M. & Nsofor, Emmanuel C., 2018. "Solidification enhancement of PCM in a triplex-tube thermal energy storage system with nanoparticles and fins," Applied Energy, Elsevier, vol. 211(C), pages 975-986.
    11. Hong, Ying-Yi & Beltran, Angelo A. & Paglinawan, Arnold C., 2018. "A robust design of maximum power point tracking using Taguchi method for stand-alone PV system," Applied Energy, Elsevier, vol. 211(C), pages 50-63.
    12. Kurnia, Jundika C. & Sasmito, Agus P., 2018. "Numerical investigation of heat transfer performance of a rotating latent heat thermal energy storage," Applied Energy, Elsevier, vol. 227(C), pages 542-554.
    13. Reji Kumar, R. & Samykano, M. & Pandey, A.K. & Kadirgama, K. & Tyagi, V.V., 2020. "Phase change materials and nano-enhanced phase change materials for thermal energy storage in photovoltaic thermal systems: A futuristic approach and its technical challenges," Renewable and Sustainable Energy Reviews, Elsevier, vol. 133(C).
    14. Zhao, B.C. & Li, T.X. & Gao, J.C. & Wang, R.Z., 2020. "Latent heat thermal storage using salt hydrates for distributed building heating: A multi-level scale-up research," Renewable and Sustainable Energy Reviews, Elsevier, vol. 121(C).
    15. Yıldız, Çağatay & Arıcı, Müslüm & Nižetić, Sandro & Shahsavar, Amin, 2020. "Numerical investigation of natural convection behavior of molten PCM in an enclosure having rectangular and tree-like branching fins," Energy, Elsevier, vol. 207(C).
    16. Guo, Junfei & Liu, Zhan & Du, Zhao & Yu, Jiabang & Yang, Xiaohu & Yan, Jinyue, 2021. "Effect of fin-metal foam structure on thermal energy storage: An experimental study," Renewable Energy, Elsevier, vol. 172(C), pages 57-70.
    17. Li, Gang, 2016. "Sensible heat thermal storage energy and exergy performance evaluations," Renewable and Sustainable Energy Reviews, Elsevier, vol. 53(C), pages 897-923.
    18. Ma, Xiaowei & Zhang, Quan & Zou, Sikai, 2022. "An experimental and numerical study on the thermal performance of a loop thermosyphon integrated with latent thermal energy storage for emergency cooling in a data center," Energy, Elsevier, vol. 253(C).
    19. Liu, Zhan & Liu, Zihui & Guo, Junfei & Wang, Fan & Yang, Xiaohu & Yan, Jinyue, 2022. "Innovative ladder-shaped fin design on a latent heat storage device for waste heat recovery," Applied Energy, Elsevier, vol. 321(C).
    20. Mahdi, Jasim M. & Nsofor, Emmanuel C., 2017. "Solidification enhancement in a triplex-tube latent heat energy storage system using nanoparticles-metal foam combination," Energy, Elsevier, vol. 126(C), pages 501-512.
    21. Yao, Shouguang & Huang, Xinyu, 2021. "Study on solidification performance of PCM by longitudinal triangular fins in a triplex-tube thermal energy storage system," Energy, Elsevier, vol. 227(C).
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Huang, Xinyu & Li, Fangfei & Xiao, Tian & Li, Yuanji & Yang, Xiaohu & He, Ya-Ling, 2023. "Structural optimization of melting process of a latent heat energy storage unit and application of flip mechanism," Energy, Elsevier, vol. 280(C).
    2. Huang, Xinyu & Li, Fangfei & Guo, Junfei & Li, Yuanji & Du, Rui & Yang, Xiaohu & He, Ya-Ling, 2024. "Design optimization on solidification performance of a rotating latent heat thermal energy storage system subject to fluctuating heat source," Applied Energy, Elsevier, vol. 362(C).
    3. Tao Ning & Xinyu Huang & Junwei Su & Xiaohu Yang, 2023. "Design and Research of Heat Storage Enhancement by Innovative Wave Fin in a Hot Water–Oil-Displacement System," Sustainability, MDPI, vol. 15(22), pages 1-17, November.
    4. Yang, Chao & Xu, Xing-Rong & Bake, Maitiniyazi & Wu, Chun-Mei & Li, You-Rong & Zheng, Zhang-Jing & Yu, Jia-Jia, 2024. "Numerical investigation and optimization of the melting performance of latent heat thermal energy storage unit strengthened by graded metal foam and mechanical rotation," Renewable Energy, Elsevier, vol. 227(C).
    5. Liu, Zhan & Ding, Jialu & Huang, Xinyu & Liu, Zhengguang & Yan, Xuewen & Liu, Xianglei & Yang, Xiaohu, 2024. "Analysis of a hybrid heat and underwater compressed air energy storage system used at coastal areas," Applied Energy, Elsevier, vol. 354(PA).
    6. Bian, Yifan & Xie, Lirong & Ye, Jiahao & Ma, Lan & Cui, Chuanshi, 2024. "Peer-to-peer energy sharing model considering multi-objective optimal allocation of shared energy storage in a multi-microgrid system," Energy, Elsevier, vol. 288(C).
    7. Li, Yuanji & Niu, Zhaoyang & Gao, Xinyu & Ji, Ruiyang & Yang, Xiaohu & Yan, Jinyue, 2023. "Experimental and numerical investigations on tilt filling design of metal foam in a heat storage tank," Renewable Energy, Elsevier, vol. 217(C).
    8. Wang, Yabo & Huang, Xinyu & Shu, Gao & Li, Xueqiang & Yang, Xiaohu, 2024. "Influence of microgravity on melting performance of a phase-change heat storage tank," Energy, Elsevier, vol. 289(C).
    9. Huang, Xinyu & Li, Fangfei & Liu, Zhengguang & Gao, Xinyu & Yang, Xiaohu & Yan, Jinyue, 2023. "Design and optimization of a novel phase change photovoltaic thermal utilization structure for building envelope," Renewable Energy, Elsevier, vol. 218(C).
    10. Luo, Haizhi & Wang, Chenglong & Li, Cangbai & Meng, Xiangzhao & Yang, Xiaohu & Tan, Qian, 2024. "Multi-scale carbon emission characterization and prediction based on land use and interpretable machine learning model: A case study of the Yangtze River Delta Region, China," Applied Energy, Elsevier, vol. 360(C).
    11. Yassine Rami & Amine Allouhi, 2024. "Design, Economic, and Environmental Accounting Assessment of a Solar-Powered Cold Room for Fish Storage in Traditional Markets," Sustainability, MDPI, vol. 16(7), pages 1-22, April.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Huang, Xinyu & Li, Fangfei & Xiao, Tian & Guo, Junfei & Wang, Fan & Gao, Xinyu & Yang, Xiaohu & He, Ya-Ling, 2023. "Investigation and optimization of solidification performance of a triplex-tube latent heat thermal energy storage system by rotational mechanism," Applied Energy, Elsevier, vol. 331(C).
    2. Mohammad Ghalambaz & Hayder I. Mohammed & Jasim M. Mahdi & Amir Hossein Eisapour & Obai Younis & Aritra Ghosh & Pouyan Talebizadehsardari & Wahiba Yaïci, 2021. "Intensifying the Charging Response of a Phase-Change Material with Twisted Fin Arrays in a Shell-And-Tube Storage System," Energies, MDPI, vol. 14(6), pages 1-19, March.
    3. Mohammad Ghalambaz & Jasim M. Mahdi & Amirhossein Shafaghat & Amir Hossein Eisapour & Obai Younis & Pouyan Talebizadeh Sardari & Wahiba Yaïci, 2021. "Effect of Twisted Fin Array in a Triple-Tube Latent Heat Storage System during the Charging Mode," Sustainability, MDPI, vol. 13(5), pages 1-15, March.
    4. Xinguo Sun & Jasim M. Mahdi & Hayder I. Mohammed & Hasan Sh. Majdi & Wang Zixiong & Pouyan Talebizadehsardari, 2021. "Solidification Enhancement in a Triple-Tube Latent Heat Energy Storage System Using Twisted Fins," Energies, MDPI, vol. 14(21), pages 1-23, November.
    5. Yan, Peiliang & Fan, Weijun & Han, Yu & Ding, Hongbing & Wen, Chuang & Elbarghthi, Anas F.A. & Yang, Yan, 2023. "Leaf-vein bionic fin configurations for enhanced thermal energy storage performance of phase change materials in smart heating and cooling systems," Applied Energy, Elsevier, vol. 346(C).
    6. Mahdi, Jasim M. & Mohammed, Hayder I. & Hashim, Emad T. & Talebizadehsardari, Pouyan & Nsofor, Emmanuel C., 2020. "Solidification enhancement with multiple PCMs, cascaded metal foam and nanoparticles in the shell-and-tube energy storage system," Applied Energy, Elsevier, vol. 257(C).
    7. Choi, Sung Ho & Ko, Han Seo & Sohn, Dong Kee, 2022. "Bubble-driven flow enhancement of heat discharge of latent heat thermal energy storage," Energy, Elsevier, vol. 244(PB).
    8. Choi, Sung Ho & Sohn, Dong Kee & Ko, Han Seo, 2021. "Performance enhancement of latent heat thermal energy storage by bubble-driven flow," Applied Energy, Elsevier, vol. 302(C).
    9. Shahsavar, Amin & Goodarzi, Abbas & Mohammed, Hayder I. & Shirneshan, Alireza & Talebizadehsardari, Pouyan, 2020. "Thermal performance evaluation of non-uniform fin array in a finned double-pipe latent heat storage system," Energy, Elsevier, vol. 193(C).
    10. Duan, Juan & Peng, Zeyu, 2022. "Numerical investigation of nano-enhanced phase change material melting in the 3D annular tube with spiral fins," Renewable Energy, Elsevier, vol. 193(C), pages 251-263.
    11. Ewelina Radomska & Lukasz Mika & Karol Sztekler & Lukasz Lis, 2020. "The Impact of Heat Exchangers’ Constructions on the Melting and Solidification Time of Phase Change Materials," Energies, MDPI, vol. 13(18), pages 1-44, September.
    12. Ge, Ruihuan & Li, Qi & Li, Chuan & Liu, Qing, 2022. "Evaluation of different melting performance enhancement structures in a shell-and-tube latent heat thermal energy storage system," Renewable Energy, Elsevier, vol. 187(C), pages 829-843.
    13. Cao, Xiaoling & Zhang, Nan & Yuan, Yanping & Luo, Xiaolong, 2020. "Thermal performance of triplex-tube latent heat storage exchanger: simultaneous heat storage and hot water supply via condensation heat recovery," Renewable Energy, Elsevier, vol. 157(C), pages 616-625.
    14. Jiang, Jiajie & Hong, Yuxiang & Li, Qing & Du, Juan, 2023. "Evaluating the impacts of fin structures and fin counts on photovoltaic panels integrated with phase change material," Energy, Elsevier, vol. 283(C).
    15. Yan, Peiliang & Fan, Weijun & Yang, Yan & Ding, Hongbing & Arshad, Adeel & Wen, Chuang, 2022. "Performance enhancement of phase change materials in triplex-tube latent heat energy storage system using novel fin configurations," Applied Energy, Elsevier, vol. 327(C).
    16. Mohammad Javad Zarei & Hassan Bazai & Mohsen Sharifpur & Omid Mahian & Bahman Shabani, 2020. "The Effects of Fin Parameters on the Solidification of PCMs in a Fin-Enhanced Thermal Energy Storage System," Energies, MDPI, vol. 13(1), pages 1-20, January.
    17. Zhang, Chunwei & Yu, Meng & Fan, Yubin & Zhang, Xuejun & Zhao, Yang & Qiu, Limin, 2020. "Numerical study on heat transfer enhancement of PCM using three combined methods based on heat pipe," Energy, Elsevier, vol. 195(C).
    18. Huang, Shengyao & Lv, Laiquan & Rong, Yan & Zhou, Hao, 2024. "Experimental study on the thermal characteristics of a visualized shell-and-tube LHTES system at different endothermic and exothermic temperatures," Renewable Energy, Elsevier, vol. 221(C).
    19. Fei Ma & Tianji Zhu & Yalin Zhang & Xinli Lu & Wei Zhang & Feng Ma, 2023. "A Review on Heat Transfer Enhancement of Phase Change Materials Using Fin Tubes," Energies, MDPI, vol. 16(1), pages 1-25, January.
    20. Cui, Wei & Si, Tianyu & Li, Xiangxuan & Li, Xinyi & Lu, Lin & Ma, Ting & Wang, Qiuwang, 2022. "Heat transfer enhancement of phase change materials embedded with metal foam for thermal energy storage: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 169(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:271:y:2023:i:c:s0360544223004942. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.