IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v336y2023ics0306261923001149.html
   My bibliography  Save this article

Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene

Author

Listed:
  • Li, Jinhu
  • Ye, Xinhao
  • Burra, Kiran G.
  • Lu, Wei
  • Wang, Zhiwei
  • Liu, Xuan
  • Gupta, Ashwani K.

Abstract

The thermal conversion of waste plastic products can provide a promising solution to the issues of environmental pollution, waste management, and energy needs. However, our present understanding on the thermal reforming of different kinds of plastic wastes mixtures during their co-pyrolysis and co-gasification for syngas production and energy recovery is insufficient. Non-selective urban polypropylene (PP) and polystyrene (PS) waste plastics were chosen for the investigations reported here. Thermal degradation properties of PP and PS as well as their blends in different mass ratios were investigated via thermogravimetric (TG) analysis. Co-pyrolysis and CO2-assisted co-gasification of PP-PS blends were then conducted using a fixed-bed reactor at a temperature of 1173 K. Experimental results from the blends were then compared with the weighted value calculated from their component feedstocks to quantify the degree of synergistic effect. TG results showed that the co-treatment of PP and PS enhanced the respective devolatilization process. The co-pyrolysis of PP and PS enhanced their thermal cracking, leading to synergistic increases in the yields of H2, light hydrocarbons (HC) and total syngas. In co-gasification, the reforming reaction involving CO2 was synergistically enhanced, resulting in the increased yields of H2 and HC. The gasification reactivity of carbon black improved during the co-processing of PP and PS due to the synergistic effect between the two different kinds of plastics. Higher synergistic effects were observed from the plastic mixtures having higher PS content that resulted in increased yield of syngas. Co-gasification of PP-PS blends having 40% PP content (2P3S) exhibited the maximum synergistic effect on H2, CO, and total syngas showing increased yields by 88.8%, 77.7%, and 74.2% respectively. The lowest synergistic effect was observed for HC that showed increased yield of only 25.1%. The optimal CO2 consumption was also observed from the co-gasification of 2P3S. Each gram of 2P3S feedstock consumed approximately 1.80 g of CO2 to result in highest recovered energy of 27.49 kJ/g and the maximum overall energy efficiency of 43.2%. The results revealed that enhanced thermal cracking and CO2 reforming reaction, along with the improved reactivity of carbon black were mainly responsible for increased yields of H2, HC, CO and total syngas during co-gasification. This study contributes to the fundamental understanding of co-processing of non-separated waste plastics for enhanced syngas production and energy recovery, elucidating the synergistic effect between the various kinds of plastics during their co-pyrolysis and co-gasification.

Suggested Citation

  • Li, Jinhu & Ye, Xinhao & Burra, Kiran G. & Lu, Wei & Wang, Zhiwei & Liu, Xuan & Gupta, Ashwani K., 2023. "Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene," Applied Energy, Elsevier, vol. 336(C).
    • Handle: RePEc:eee:appene:v:336:y:2023:i:c:s0306261923001149
    DOI: 10.1016/j.apenergy.2023.120750
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261923001149
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2023.120750?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Chen, Zhaohui & Li, Yunjia & Lai, Dengguo & Geng, Sulong & Zhou, Qi & Gao, Shiqiu & Xu, Guangwen, 2018. "Coupling coal pyrolysis with char gasification in a multi-stage fluidized bed to co-produce high-quality tar and syngas," Applied Energy, Elsevier, vol. 215(C), pages 348-355.
    2. Wong, S.L. & Ngadi, N. & Abdullah, T.A.T. & Inuwa, I.M., 2015. "Current state and future prospects of plastic waste as source of fuel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 50(C), pages 1167-1180.
    3. Singh, P. & Déparrois, N. & Burra, K.G. & Bhattacharya, S. & Gupta, A.K., 2019. "Energy recovery from cross-linked polyethylene wastes using pyrolysis and CO2 assisted gasification," Applied Energy, Elsevier, vol. 254(C).
    4. Lahijani, Pooya & Zainal, Zainal Alimuddin & Mohammadi, Maedeh & Mohamed, Abdul Rahman, 2015. "Conversion of the greenhouse gas CO2 to the fuel gas CO via the Boudouard reaction: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 41(C), pages 615-632.
    5. Déparrois, N. & Singh, P. & Burra, K.G. & Gupta, A.K., 2019. "Syngas production from co-pyrolysis and co-gasification of polystyrene and paper with CO2," Applied Energy, Elsevier, vol. 246(C), pages 1-10.
    6. Burra, K.G. & Gupta, A.K., 2018. "Synergistic effects in steam gasification of combined biomass and plastic waste mixtures," Applied Energy, Elsevier, vol. 211(C), pages 230-236.
    7. Ahmed, I.I. & Gupta, A.K., 2013. "Experiments and stochastic simulations of lignite coal during pyrolysis and gasification," Applied Energy, Elsevier, vol. 102(C), pages 355-363.
    8. Liu, Xuan & Burra, Kiran G. & Wang, Zhiwei & Li, Jinhu & Che, Defu & Gupta, Ashwani K., 2020. "On deconvolution for understanding synergistic effects in co-pyrolysis of pinewood and polypropylene," Applied Energy, Elsevier, vol. 279(C).
    9. Li, Jinhu & Burra, Kiran Raj G. & Wang, Zhiwei & Liu, Xuan & Gupta, Ashwani K., 2021. "Co-gasification of high-density polyethylene and pretreated pine wood," Applied Energy, Elsevier, vol. 285(C).
    10. Parthasarathy, Prakash & Narayanan, K. Sheeba, 2014. "Hydrogen production from steam gasification of biomass: Influence of process parameters on hydrogen yield – A review," Renewable Energy, Elsevier, vol. 66(C), pages 570-579.
    11. Policella, Matteo & Wang, Zhiwei & Burra, Kiran. G. & Gupta, Ashwani K., 2019. "Characteristics of syngas from pyrolysis and CO2-assisted gasification of waste tires," Applied Energy, Elsevier, vol. 254(C).
    12. Wang, Zhiwei & Burra, Kiran G. & Zhang, Mengju & Li, Xueqin & He, Xiaofeng & Lei, Tingzhou & Gupta, Ashwani K., 2020. "Syngas evolution and energy efficiency in CO2-assisted gasification of pine bark," Applied Energy, Elsevier, vol. 269(C).
    13. Ahmed, I. & Gupta, A.K., 2009. "Evolution of syngas from cardboard gasification," Applied Energy, Elsevier, vol. 86(9), pages 1732-1740, September.
    14. Park, Ki-Bum & Jeong, Yong-Seong & Kim, Joo-Sik, 2019. "Activator-assisted pyrolysis of polypropylene," Applied Energy, Elsevier, vol. 253(C), pages 1-1.
    15. Liu, Xuan & Burra, Kiran Raj G. & Wang, Zhiwei & Li, Jinhu & Che, Defu & Gupta, Ashwani K., 2021. "Towards enhanced understanding of synergistic effects in co-pyrolysis of pinewood and polycarbonate," Applied Energy, Elsevier, vol. 289(C).
    16. Ahmed, I. & Gupta, A.K., 2009. "Characteristics of cardboard and paper gasification with CO2," Applied Energy, Elsevier, vol. 86(12), pages 2626-2634, December.
    17. Bellomare, Filippo & Rokni, Masoud, 2013. "Integration of a municipal solid waste gasification plant with solid oxide fuel cell and gas turbine," Renewable Energy, Elsevier, vol. 55(C), pages 490-500.
    18. Zhang, Yayun & Duan, Dengle & Lei, Hanwu & Villota, Elmar & Ruan, Roger, 2019. "Jet fuel production from waste plastics via catalytic pyrolysis with activated carbons," Applied Energy, Elsevier, vol. 251(C), pages 1-1.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Mohamed, Badr A. & O'Boyle, Marnie & Li, Loretta Y., 2023. "Co-pyrolysis of sewage sludge with lignocellulosic and algal biomass for sustainable liquid and gaseous fuel production: A life cycle assessment and techno-economic analysis," Applied Energy, Elsevier, vol. 346(C).
    2. Yinnan, He & Ruxiang, Qin & Bangjun, Wang, 2023. "Spatial and temporal convergence of provincial coal mine safety accidents and production and their influencing factors: Data from 23 coal-producing provinces in China (2005–2021)," Resources Policy, Elsevier, vol. 86(PB).
    3. Ayub, Yousaf & Zhou, Jianzhao & Shen, Weifeng & Ren, Jingzheng, 2023. "Innovative valorization of biomass waste through integration of pyrolysis and gasification: Process design, optimization, and multi-scenario sustainability analysis," Energy, Elsevier, vol. 282(C).
    4. Samy Yousef & Vidas Lekavičius & Nerijus Striūgas, 2023. "Techno-Economic Analysis of Thermochemical Conversion of Waste Masks Generated in the EU during COVID-19 Pandemic into Energy Products," Energies, MDPI, vol. 16(9), pages 1-14, May.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Wang, Zhiwei & Burra, Kiran G. & Li, Xueqin & Zhang, Mengju & He, Xiaofeng & Lei, Tingzhou & Gupta, Ashwani K., 2020. "CO2-assisted gasification of polyethylene terephthalate with focus on syngas evolution and solid yield," Applied Energy, Elsevier, vol. 276(C).
    2. Wang, Zhiwei & Burra, Kiran G. & Zhang, Mengju & Li, Xueqin & He, Xiaofeng & Lei, Tingzhou & Gupta, Ashwani K., 2020. "Syngas evolution and energy efficiency in CO2-assisted gasification of pine bark," Applied Energy, Elsevier, vol. 269(C).
    3. Mariyam, Sabah & Shahbaz, Muhammad & Al-Ansari, Tareq & Mackey, Hamish. R & McKay, Gordon, 2022. "A critical review on co-gasification and co-pyrolysis for gas production," Renewable and Sustainable Energy Reviews, Elsevier, vol. 161(C).
    4. Aktas, Fatih & Mavukwana, Athi-enkosi & Burra, Kiran Raj Goud & Gupta, Ashwani K., 2024. "Role of spent FCC catalyst in pyrolysis and CO2-assisted gasification of pinewood," Applied Energy, Elsevier, vol. 366(C).
    5. Burra, Kiran Raj G. & Liu, Xuan & Wang, Zhiwei & Li, Jinhu & Che, Defu & Gupta, Ashwani K., 2021. "Quantifying the sources of synergistic effects in co-pyrolysis of pinewood and polystyrene," Applied Energy, Elsevier, vol. 302(C).
    6. Liu, Xuan & Burra, Kiran G. & Wang, Zhiwei & Li, Jinhu & Che, Defu & Gupta, Ashwani K., 2020. "On deconvolution for understanding synergistic effects in co-pyrolysis of pinewood and polypropylene," Applied Energy, Elsevier, vol. 279(C).
    7. Déparrois, N. & Singh, P. & Burra, K.G. & Gupta, A.K., 2019. "Syngas production from co-pyrolysis and co-gasification of polystyrene and paper with CO2," Applied Energy, Elsevier, vol. 246(C), pages 1-10.
    8. Li, Jinhu & Burra, Kiran Raj G. & Wang, Zhiwei & Liu, Xuan & Gupta, Ashwani K., 2021. "Co-gasification of high-density polyethylene and pretreated pine wood," Applied Energy, Elsevier, vol. 285(C).
    9. Patrik Šuhaj & Jakub Husár & Juma Haydary, 2020. "Gasification of RDF and Its Components with Tire Pyrolysis Char as Tar-Cracking Catalyst," Sustainability, MDPI, vol. 12(16), pages 1-14, August.
    10. Zhao, Xiang & You, Fengqi, 2021. "Waste respirator processing system for public health protection and climate change mitigation under COVID-19 pandemic: Novel process design and energy, environmental, and techno-economic perspectives," Applied Energy, Elsevier, vol. 283(C).
    11. Lucio Zaccariello & Maria Laura Mastellone, 2023. "Fuel Gas Production from the Co-Gasification of Coal, Plastic Waste, and Wood in a Fluidized Bed Reactor: Effect of Gasifying Agent and Bed Material," Sustainability, MDPI, vol. 15(9), pages 1-19, May.
    12. Yao, Dingding & Wang, Chi-Hwa, 2020. "Pyrolysis and in-line catalytic decomposition of polypropylene to carbon nanomaterials and hydrogen over Fe- and Ni-based catalysts," Applied Energy, Elsevier, vol. 265(C).
    13. Dmitry Porshnov, 2022. "Evolution of pyrolysis and gasification as waste to energy tools for low carbon economy," Wiley Interdisciplinary Reviews: Energy and Environment, Wiley Blackwell, vol. 11(1), January.
    14. Huang, Jijiang & Veksha, Andrei & Chan, Wei Ping & Giannis, Apostolos & Lisak, Grzegorz, 2022. "Chemical recycling of plastic waste for sustainable material management: A prospective review on catalysts and processes," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    15. Park, Ki-Bum & Choi, Min-Jun & Chae, Da-Yeong & Jung, Jaeheum & Kim, Joo-Sik, 2022. "Separate two-step and continuous two-stage pyrolysis of a waste plastic mixture to produce a chlorine-depleted oil," Energy, Elsevier, vol. 244(PA).
    16. Ahmed, I.I. & Gupta, A.K., 2013. "Experiments and stochastic simulations of lignite coal during pyrolysis and gasification," Applied Energy, Elsevier, vol. 102(C), pages 355-363.
    17. Nipattummakul, Nimit & Ahmed, Islam I. & Kerdsuwan, Somrat & Gupta, Ashwani K., 2012. "Steam gasification of oil palm trunk waste for clean syngas production," Applied Energy, Elsevier, vol. 92(C), pages 778-782.
    18. Tian, Hailin & Li, Jie & Yan, Miao & Tong, Yen Wah & Wang, Chi-Hwa & Wang, Xiaonan, 2019. "Organic waste to biohydrogen: A critical review from technological development and environmental impact analysis perspective," Applied Energy, Elsevier, vol. 256(C).
    19. Du, Hong & Ma, Xiuyun & Jiang, Miao & Yan, Peifang & Zhang, Z.Conrad, 2021. "Autocatalytic co-upgrading of biochar and pyrolysis gas to syngas," Energy, Elsevier, vol. 221(C).
    20. Zhang, Qinglin & Dor, Liran & Fenigshtein, Dikla & Yang, Weihong & Blasiak, Wlodzmierz, 2012. "Gasification of municipal solid waste in the Plasma Gasification Melting process," Applied Energy, Elsevier, vol. 90(1), pages 106-112.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:336:y:2023:i:c:s0306261923001149. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.