IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v15y2023i3p1957-d1041852.html
   My bibliography  Save this article

Improving the Heat Transfer of Phase Change Composites for Thermal Energy Storage by Adding Copper: Preparation and Thermal Properties

Author

Listed:
  • Abdelwaheb Trigui

    (Laboratoire des Matériaux Multifonctionnels et Applications (LaMMA), Université de Sfax, Sfax 3038, Tunisia)

  • Makki Abdelmouleh

    (Laboratoire Sciences des Matériaux et Environnement (LMSE), Université de Sfax, Sfax 3038, Tunisia)

Abstract

Phase change materials (PCMs), as an effective thermal energy storage technology, provide a viable approach to harness solar heat, a green energy source, and optimize energy consumption in buildings. However, the obstacle preventing widespread practical use of PCM is its poor performance in terms of heat transfer and shape stabilization. This article focuses on the application of the shape stabilization method. To improve the thermal conductivity of organic PCMs (hexadecane), copper microparticles are added to form phase change composites (PCC). This process allows an enhanced PCM (75 wt%) that distributes effective thermal storage capabilities while maintaining low cost. SEM, FTIR, ATG, infrared thermography (IRT), and DSC were used to characterize the composites’ micromorphology, chemical composition, thermal degradation stability, and thermal energy storage capabilities. DSC results showed that a proportion of 75 wt% phase change material with 15 wt% Cu had excellent thermal stability and high energy storage density per unit mass. In light of its high latent heat storage capacity of 201.32 J/g as well as its ability to prevent Hexadecane exudation, PCC ensures higher thermal conductivity and shape stability during phase transition than ordinary PCM. The incorporation of Cu to paraffin causes delay in PCM phase transformation, leading it to respond to rapid charging and discharging rates and, consequentially, to challenges in temperature control, as shown by IRT. The new PCCs had favorable thermal stability below 100 °C, which was advantageous for practical application for thermal energy storage and management, and notably for solar thermal energy storage.

Suggested Citation

  • Abdelwaheb Trigui & Makki Abdelmouleh, 2023. "Improving the Heat Transfer of Phase Change Composites for Thermal Energy Storage by Adding Copper: Preparation and Thermal Properties," Sustainability, MDPI, vol. 15(3), pages 1-19, January.
    • Handle: RePEc:gam:jsusta:v:15:y:2023:i:3:p:1957-:d:1041852
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/15/3/1957/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/2071-1050/15/3/1957/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Cui, Wenlong & Yuan, Yanping & Sun, Liangliang & Cao, Xiaoling & Yang, Xiaojiao, 2016. "Experimental studies on the supercooling and melting/freezing characteristics of nano-copper/sodium acetate trihydrate composite phase change materials," Renewable Energy, Elsevier, vol. 99(C), pages 1029-1037.
    2. Wang, Lijiu & Meng, Duo, 2010. "Fatty acid eutectic/polymethyl methacrylate composite as form-stable phase change material for thermal energy storage," Applied Energy, Elsevier, vol. 87(8), pages 2660-2665, August.
    3. Vélez, C. & Khayet, M. & Ortiz de Zárate, J.M., 2015. "Temperature-dependent thermal properties of solid/liquid phase change even-numbered n-alkanes: n-Hexadecane, n-octadecane and n-eicosane," Applied Energy, Elsevier, vol. 143(C), pages 383-394.
    4. Mehrali, Mohammad & Latibari, Sara Tahan & Mehrali, Mehdi & Indra Mahlia, Teuku Meurah & Cornelis Metselaar, Hendrik Simon, 2013. "Preparation and properties of highly conductive palmitic acid/graphene oxide composites as thermal energy storage materials," Energy, Elsevier, vol. 58(C), pages 628-634.
    5. Xiao, X. & Zhang, P. & Li, M., 2013. "Preparation and thermal characterization of paraffin/metal foam composite phase change material," Applied Energy, Elsevier, vol. 112(C), pages 1357-1366.
    6. Li, Min, 2013. "A nano-graphite/paraffin phase change material with high thermal conductivity," Applied Energy, Elsevier, vol. 106(C), pages 25-30.
    7. Nourani, Moloud & Hamdami, Nasser & Keramat, Javad & Moheb, Ahmad & Shahedi, Mohammad, 2016. "Thermal behavior of paraffin-nano-Al2O3 stabilized by sodium stearoyl lactylate as a stable phase change material with high thermal conductivity," Renewable Energy, Elsevier, vol. 88(C), pages 474-482.
    8. Wang, Weilong & Yang, Xiaoxi & Fang, Yutang & Ding, Jing & Yan, Jinyue, 2009. "Enhanced thermal conductivity and thermal performance of form-stable composite phase change materials by using [beta]-Aluminum nitride," Applied Energy, Elsevier, vol. 86(7-8), pages 1196-1200, July.
    9. Wang, Weilong & Yang, Xiaoxi & Fang, Yutang & Ding, Jing, 2009. "Preparation and performance of form-stable polyethylene glycol/silicon dioxide composites as solid-liquid phase change materials," Applied Energy, Elsevier, vol. 86(2), pages 170-174, February.
    10. Meng, Z.N. & Zhang, P., 2017. "Experimental and numerical investigation of a tube-in-tank latent thermal energy storage unit using composite PCM," Applied Energy, Elsevier, vol. 190(C), pages 524-539.
    11. Huang, Xiang & Alva, Guruprasad & Liu, Lingkun & Fang, Guiyin, 2017. "Microstructure and thermal properties of cetyl alcohol/high density polyethylene composite phase change materials with carbon fiber as shape-stabilized thermal storage materials," Applied Energy, Elsevier, vol. 200(C), pages 19-27.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Leland Weiss & Ramanshu Jha, 2023. "Small-Scale Phase Change Materials in Low-Temperature Applications: A Review," Energies, MDPI, vol. 16(6), pages 1-24, March.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Lin, Yaxue & Jia, Yuting & Alva, Guruprasad & Fang, Guiyin, 2018. "Review on thermal conductivity enhancement, thermal properties and applications of phase change materials in thermal energy storage," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 2730-2742.
    2. Liu, Yang & Zheng, Ruowei & Li, Ji, 2022. "High latent heat phase change materials (PCMs) with low melting temperature for thermal management and storage of electronic devices and power batteries: Critical review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 168(C).
    3. Grzegorz Czerwiński & Jerzy Wołoszyn, 2022. "Influence of the Longitudinal and Tree-Shaped Fin Parameters on the Shell-and-Tube LHTES Energy Efficiency," Energies, MDPI, vol. 16(1), pages 1-24, December.
    4. Chen, Changzhong & Wang, Linge & Huang, Yong, 2011. "Electrospun phase change fibers based on polyethylene glycol/cellulose acetate blends," Applied Energy, Elsevier, vol. 88(9), pages 3133-3139.
    5. Zhang, P. & Xiao, X. & Ma, Z.W., 2016. "A review of the composite phase change materials: Fabrication, characterization, mathematical modeling and application to performance enhancement," Applied Energy, Elsevier, vol. 165(C), pages 472-510.
    6. Qian, Yong & Wei, Ping & Jiang, Pingkai & Li, Zhi & Yan, Yonggang & Liu, Jiping, 2013. "Preparation of a novel PEG composite with halogen-free flame retardant supporting matrix for thermal energy storage application," Applied Energy, Elsevier, vol. 106(C), pages 321-327.
    7. Li, Liping & Wang, Gang & Guo, Chuigen, 2016. "Influence of intumescent flame retardant on thermal and flame retardancy of eutectic mixed paraffin/polypropylene form-stable phase change materials," Applied Energy, Elsevier, vol. 162(C), pages 428-434.
    8. Chinnasamy, Veerakumar & Heo, Jaehyeok & Jung, Sungyong & Lee, Hoseong & Cho, Honghyun, 2023. "Shape stabilized phase change materials based on different support structures for thermal energy storage applications–A review," Energy, Elsevier, vol. 262(PB).
    9. Li, Yali & Li, Jinhong & Deng, Yong & Guan, Weimin & Wang, Xiang & Qian, Tingting, 2016. "Preparation of paraffin/porous TiO2 foams with enhanced thermal conductivity as PCM, by covering the TiO2 surface with a carbon layer," Applied Energy, Elsevier, vol. 171(C), pages 37-45.
    10. Yang, Xiaohu & Feng, Shangsheng & Zhang, Qunli & Chai, Yue & Jin, Liwen & Lu, Tian Jian, 2017. "The role of porous metal foam on the unidirectional solidification of saturating fluid for cold storage," Applied Energy, Elsevier, vol. 194(C), pages 508-521.
    11. Kenisarin, Murat M. & Kenisarina, Kamola M., 2012. "Form-stable phase change materials for thermal energy storage," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(4), pages 1999-2040.
    12. Meysam Nazari & Mohamed Jebrane & Nasko Terziev, 2020. "Bio-Based Phase Change Materials Incorporated in Lignocellulose Matrix for Energy Storage in Buildings—A Review," Energies, MDPI, vol. 13(12), pages 1-25, June.
    13. Feng, Daili & Feng, Yanhui & Qiu, Lin & Li, Pei & Zang, Yuyang & Zou, Hanying & Yu, Zepei & Zhang, Xinxin, 2019. "Review on nanoporous composite phase change materials: Fabrication, characterization, enhancement and molecular simulation," Renewable and Sustainable Energy Reviews, Elsevier, vol. 109(C), pages 578-605.
    14. Fang, Guiyin & Tang, Fang & Cao, Lei, 2014. "Preparation, thermal properties and applications of shape-stabilized thermal energy storage materials," Renewable and Sustainable Energy Reviews, Elsevier, vol. 40(C), pages 237-259.
    15. Du, Kun & Calautit, John & Eames, Philip & Wu, Yupeng, 2021. "A state-of-the-art review of the application of phase change materials (PCM) in Mobilized-Thermal Energy Storage (M-TES) for recovering low-temperature industrial waste heat (IWH) for distributed heat," Renewable Energy, Elsevier, vol. 168(C), pages 1040-1057.
    16. Yang, Haiyue & Wang, Yazhou & Yu, Qianqian & Cao, Guoliang & Yang, Rue & Ke, Jiaona & Di, Xin & Liu, Feng & Zhang, Wenbo & Wang, Chengyu, 2018. "Composite phase change materials with good reversible thermochromic ability in delignified wood substrate for thermal energy storage," Applied Energy, Elsevier, vol. 212(C), pages 455-464.
    17. Xu, Yang & Ren, Qinlong & Zheng, Zhang-Jing & He, Ya-Ling, 2017. "Evaluation and optimization of melting performance for a latent heat thermal energy storage unit partially filled with porous media," Applied Energy, Elsevier, vol. 193(C), pages 84-95.
    18. Yang, Xiaohu & Yu, Jiabang & Guo, Zengxu & Jin, Liwen & He, Ya-Ling, 2019. "Role of porous metal foam on the heat transfer enhancement for a thermal energy storage tube," Applied Energy, Elsevier, vol. 239(C), pages 142-156.
    19. Wang, Weilong & Li, Hailong & Guo, Shaopeng & He, Shiquan & Ding, Jing & Yan, Jinyue & Yang, Jianping, 2015. "Numerical simulation study on discharging process of the direct-contact phase change energy storage system," Applied Energy, Elsevier, vol. 150(C), pages 61-68.
    20. Umair, Malik Muhammad & Zhang, Yuang & Iqbal, Kashif & Zhang, Shufen & Tang, Bingtao, 2019. "Novel strategies and supporting materials applied to shape-stabilize organic phase change materials for thermal energy storage–A review," Applied Energy, Elsevier, vol. 235(C), pages 846-873.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:15:y:2023:i:3:p:1957-:d:1041852. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.