IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v15y2023i2p990-d1025929.html
   My bibliography  Save this article

Investigating a New Method-Based Internal Joint Operation Law for Optimizing the Performance of a Turbocharger Compressor

Author

Listed:
  • Rong Huang

    (School of Automotive Studies, Tongji University, Shanghai 201804, China)

  • Jimin Ni

    (School of Automotive Studies, Tongji University, Shanghai 201804, China)

  • Houchuan Fan

    (School of Automotive Studies, Tongji University, Shanghai 201804, China)

  • Xiuyong Shi

    (School of Automotive Studies, Tongji University, Shanghai 201804, China)

  • Qiwei Wang

    (School of Automotive Studies, Tongji University, Shanghai 201804, China)

Abstract

A well-matched relationship between the compressor and turbine plays an important role in improving turbocharger and engine performance. However, in the matching of turbocharger and engine, the internal operation relationship between compressor and turbine is not considered comprehensively. In order to fill this gap, this paper proposed the internal joint operation law (IJOL) method based on the internal operating characteristics of the compressor and turbine using a combination of experimental and simulation methods. On this basis, the optimization method of the compressor was proposed. Firstly, according to the basic conditions of turbocharger, the compressor power consumption and the turbine effective power at a fixed speed were solved. Secondly, the power consumption curve of the compressor and the effective power curve of the turbine were coupled to obtain the power balance point of the turbocharger. Then, the internal joint operating point was solved and coupled to obtain the IJOL method. Finally, the IJOL method was used to optimize the blade number and the blade tip profile of the compressor. The simulation results showed that for the blade number, the 8-blade compressor had the best overall performance. For the blade tip profile, compared with the original compressor, the surge performance of the impeller inlet diameter reduced by 3.12% was better than that of the original compressor. In addition, in order to compare this to engine performance with different compressor structures, a 1D engine model was constructed using GT-Power. The simulation results showed that the maximum torque of the engine corresponding to the impeller designed by the IJOL method was 4.2% higher than that of the original engine, and the minimum brake specific fuel consumption was 3.1% lower. Therefore, compared with the traditional method, the IJOL method was reasonable and practical.

Suggested Citation

  • Rong Huang & Jimin Ni & Houchuan Fan & Xiuyong Shi & Qiwei Wang, 2023. "Investigating a New Method-Based Internal Joint Operation Law for Optimizing the Performance of a Turbocharger Compressor," Sustainability, MDPI, vol. 15(2), pages 1-23, January.
  • Handle: RePEc:gam:jsusta:v:15:y:2023:i:2:p:990-:d:1025929
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/15/2/990/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2071-1050/15/2/990/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Sheng Yin & Jimin Ni & Houchuan Fan & Xiuyong Shi & Rong Huang, 2022. "A Study of Evaluation Method for Turbocharger Turbine Based on Joint Operation Curve," Sustainability, MDPI, vol. 14(16), pages 1-18, August.
    2. Ekradi, Khalil & Madadi, Ali, 2020. "Performance improvement of a transonic centrifugal compressor impeller with splitter blade by three-dimensional optimization," Energy, Elsevier, vol. 201(C).
    3. Serrano, José Ramón & Navarro, Roberto & García-Cuevas, Luis Miguel & Inhestern, Lukas Benjamin, 2018. "Turbocharger turbine rotor tip leakage loss and mass flow model valid up to extreme off-design conditions with high blade to jet speed ratio," Energy, Elsevier, vol. 147(C), pages 1299-1310.
    4. Galindo, J. & Fajardo, P. & Navarro, R. & García-Cuevas, L.M., 2013. "Characterization of a radial turbocharger turbine in pulsating flow by means of CFD and its application to engine modeling," Applied Energy, Elsevier, vol. 103(C), pages 116-127.
    5. Tanda, Giovanni & Marelli, Silvia & Marmorato, Giulio & Capobianco, Massimo, 2017. "An experimental investigation of internal heat transfer in an automotive turbocharger compressor," Applied Energy, Elsevier, vol. 193(C), pages 531-539.
    6. Moussavi, S. Abolfazl & Hajilouy Benisi, Ali & Durali, Mohammad, 2017. "Effect of splitter leading edge location on performance of an automotive turbocharger compressor," Energy, Elsevier, vol. 123(C), pages 511-520.
    7. Tüchler, Stefan & Chen, Zhihang & Copeland, Colin D., 2018. "Multipoint shape optimisation of an automotive radial compressor using a coupled computational fluid dynamics and genetic algorithm approach," Energy, Elsevier, vol. 165(PA), pages 543-561.
    8. Feneley, Adam J. & Pesiridis, Apostolos & Andwari, Amin Mahmoudzadeh, 2017. "Variable Geometry Turbocharger Technologies for Exhaust Energy Recovery and Boosting‐A Review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 71(C), pages 959-975.
    9. Chen, Lingen & Luo, Jun & Sun, Fengrui & Wu, Chih, 2005. "Optimized efficiency axial-flow compressor," Applied Energy, Elsevier, vol. 81(4), pages 409-419, August.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Serrano, José Ramón & Piqueras, Pedro & De la Morena, Joaquín & Gómez-Vilanova, Alejandro & Guilain, Stéphane, 2021. "Methodological analysis of variable geometry turbine technology impact on the performance of highly downsized spark-ignition engines," Energy, Elsevier, vol. 215(PB).
    2. José Galindo & Andrés Tiseira & Roberto Navarro & Lukas Benjamin Inhestern & Juan David Echavarría, 2022. "Numerical Analysis of the Effects of Different Rotor Tip Gaps in a Radial Turbine Operating at High Pressure Ratios Reaching Choked Flow," Energies, MDPI, vol. 15(24), pages 1-30, December.
    3. Tang, Xinzi & Wang, Zhe & Xiao, Peng & Peng, Ruitao & Liu, Xiongwei, 2020. "Uncertainty quantification based optimization of centrifugal compressor impeller for aerodynamic robustness under stochastic operational conditions," Energy, Elsevier, vol. 195(C).
    4. Galindo, José & Serrano, José Ramón & De la Morena, Joaquín & Gómez-Vilanova, Alejandro, 2022. "Physical-based variable geometry turbines predictive control to enhance new hybrid powertrains’ transient response," Energy, Elsevier, vol. 261(PB).
    5. Cheng, Hongzhi & Zhou, Chuangxin & Lu, Xingen & Zhao, Shengfeng & Han, Ge & Yang, Chengwu, 2023. "Robust aerodynamic optimization and design exploration of a wide-chord transonic fan under geometric and operational uncertainties," Energy, Elsevier, vol. 278(PB).
    6. Kim, Jeong Ho & Kim, Tong Seop, 2019. "A new approach to generate turbine map data in the sub-idle operation regime of gas turbines," Energy, Elsevier, vol. 173(C), pages 772-784.
    7. Liu, Zheng & Copeland, Colin, 2018. "New method for mapping radial turbines exposed to pulsating flows," Energy, Elsevier, vol. 162(C), pages 1205-1222.
    8. Menaz Ahamed & Apostolos Pesyridis & Jabraeil Ahbabi Saray & Amin Mahmoudzadeh Andwari & Ayat Gharehghani & Srithar Rajoo, 2023. "Comparative Assessment of sCO2 Cycles, Optimal ORC, and Thermoelectric Generators for Exhaust Waste Heat Recovery Applications from Heavy-Duty Diesel Engines," Energies, MDPI, vol. 16(11), pages 1-21, May.
    9. Zhao, Rongchao & Li, Weihua & Zhuge, Weilin & Zhang, Yangjun & Yin, Yong & Wu, Yonghui, 2018. "Characterization of two-stage turbine system under steady and pulsating flow conditions," Energy, Elsevier, vol. 148(C), pages 407-423.
    10. Damian Obidowski & Mateusz Stajuda & Krzysztof Sobczak, 2021. "Efficient Multi-Objective CFD-Based Optimization Method for a Scroll Distributor," Energies, MDPI, vol. 14(2), pages 1-20, January.
    11. Wang, Zhiqi & Xie, Baoqi & Xia, Xiaoxia & Yang, Huya & Zuo, Qingsong & Liu, Zhipeng, 2022. "Energy loss of radial inflow turbine for organic Rankine cycle using mixture based on entropy production method," Energy, Elsevier, vol. 245(C).
    12. Marco Bicchi & Michele Marconcini & Ernani Fulvio Bellobuono & Elisabetta Belardini & Lorenzo Toni & Andrea Arnone, 2023. "Multi-Point Surrogate-Based Approach for Assessing Impacts of Geometric Variations on Centrifugal Compressor Performance," Energies, MDPI, vol. 16(4), pages 1-21, February.
    13. Salvo, Orlando de & Vaz de Almeida, Flávio G., 2019. "Influence of technologies on energy efficiency results of official Brazilian tests of vehicle energy consumption," Applied Energy, Elsevier, vol. 241(C), pages 98-112.
    14. Di Battista, D. & Fatigati, F. & Carapellucci, R. & Cipollone, R., 2019. "Inverted Brayton Cycle for waste heat recovery in reciprocating internal combustion engines," Applied Energy, Elsevier, vol. 253(C), pages 1-1.
    15. Tüchler, Stefan & Chen, Zhihang & Copeland, Colin D., 2018. "Multipoint shape optimisation of an automotive radial compressor using a coupled computational fluid dynamics and genetic algorithm approach," Energy, Elsevier, vol. 165(PA), pages 543-561.
    16. Wenyu Gu & Wanhua Su, 2023. "Study on the Effects of Exhaust Gas Recirculation and Fuel Injection Strategy on Transient Process Performance of Diesel Engines," Sustainability, MDPI, vol. 15(16), pages 1-21, August.
    17. Tregenza, Owen & Olshina, Noam & Hield, Peter & Manzie, Chris & Hulston, Chris, 2022. "A comparison of turbine mass flow models based on pragmatic identification data sets for turbogenerator model development," Energy, Elsevier, vol. 247(C).
    18. Mamdouh Alshammari & Nikolaos Xypolitas & Apostolos Pesyridis, 2019. "Modelling of Electrically-Assisted Turbocharger Compressor Performance," Energies, MDPI, vol. 12(6), pages 1-25, March.
    19. Sheng Yin & Jimin Ni & Houchuan Fan & Xiuyong Shi & Rong Huang, 2022. "A Study of Evaluation Method for Turbocharger Turbine Based on Joint Operation Curve," Sustainability, MDPI, vol. 14(16), pages 1-18, August.
    20. Anna Minasyan & Jordan Bradshaw & Apostolos Pesyridis, 2018. "Design and Performance Evaluation of an Axial Inflow Turbocharger Turbine," Energies, MDPI, vol. 11(2), pages 1-26, January.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:15:y:2023:i:2:p:990-:d:1025929. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.