IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i21p7941-d953392.html
   My bibliography  Save this article

Experimental Research on the Flow and Heat Transfer Characteristics of Subcritical and Supercritical Water in the Vertical Upward Smooth and Rifled Tubes

Author

Listed:
  • Xiaocheng Du

    (State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China)

  • Weiteng Li

    (State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China)

  • Xirong Zhang

    (State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China)

  • Jingrong Chen

    (State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China)

  • Tingyu Chen

    (State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China)

  • Dong Yang

    (State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China)

Abstract

Experiments were conducted to investigate the heat transfer and flow characteristics of the vertical upward smooth and rifled tubes from subcritical to supercritical pressure. The distributions of wall temperature and heat transfer coefficient (HTC) were obtained, and the HTC correlations and friction resistance coefficient correlations were fitted with experimental data. In addition, the influences of heat flux and type of tube on heat transfer performance were analyzed. The research shows that heat flux has different influences on the heat transfer characteristics under different pressures. The increase in heat flux improves the heat transfer characteristics in the nucleate boiling region, yet it leads to the advance in heat transfer deterioration. However, for supercritical water, the increase in heat flux reduces the heat transfer ability. In addition, using the rifled tube not only improves the heat transfer performance, but also inhibits the occurrence of heat transfer deterioration. The fitted correlations have great predictive ability for the heat transfer coefficient and friction resistance coefficient, and the average relative fitting errors are limited to 20%.

Suggested Citation

  • Xiaocheng Du & Weiteng Li & Xirong Zhang & Jingrong Chen & Tingyu Chen & Dong Yang, 2022. "Experimental Research on the Flow and Heat Transfer Characteristics of Subcritical and Supercritical Water in the Vertical Upward Smooth and Rifled Tubes," Energies, MDPI, vol. 15(21), pages 1-22, October.
  • Handle: RePEc:gam:jeners:v:15:y:2022:i:21:p:7941-:d:953392
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/21/7941/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/15/21/7941/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Heng Chen & Yungang Wang & Qinxin Zhao & Haidong Ma & Yuxin Li & Zhongya Chen, 2014. "Experimental Investigation of Heat Transfer and Pressure Drop Characteristics of H-type Finned Tube Banks," Energies, MDPI, vol. 7(11), pages 1-11, November.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Ko, Yun Mo & Song, Joo Young & Lee, Jae Won & Sohn, Sangho & Song, Chan Ho & Khoshvaght-Aliabadi, Morteza & Kim, Yongchan & Kang, Yong Tae, 2024. "A critical review on Colburn j-factor and f-factor and energy performance analysis for finned tube heat exchangers," Energy, Elsevier, vol. 287(C).
    2. Pradhyumn Bhale & Mrinal Kaushik & Jane-Sunn Liaw & Chi-Chuan Wang, 2019. "Airside Performance of H-Type Finned Tube Banks with Surface Modifications," Energies, MDPI, vol. 12(4), pages 1-16, February.
    3. Rajesh Ravi & Senthilkumar Pachamuthu, 2018. "Design and Development of Innovative Protracted-Finned Counter Flow Heat Exchanger (PFCHE) for an Engine WHR and Its Impact on Exhaust Emissions," Energies, MDPI, vol. 11(10), pages 1-19, October.
    4. Ali Sadeghianjahromi & Saeid Kheradmand & Hossain Nemati & Jane-Sunn Liaw & Chi-Chuan Wang, 2018. "Compound Heat Transfer Enhancement of Wavy Fin-and-Tube Heat Exchangers through Boundary Layer Restarting and Swirled Flow," Energies, MDPI, vol. 11(8), pages 1-19, July.
    5. Wang, Jingyi & Hua, Jing & Fu, Lin & Wang, Zhe & Zhang, Shigang, 2019. "A theoretical fundamental investigation on boilers equipped with vapor-pump system for Flue-Gas Heat and Moisture Recovery," Energy, Elsevier, vol. 171(C), pages 956-970.
    6. Jing Zhao & Wei Liu & Bin Li & Xiangdong Liu & Congzhe Gao & Zhongxin Gu, 2015. "Investigation of Electromagnetic, Thermal and Mechanical Characteristics of a Five-Phase Dual-Rotor Permanent-Magnet Synchronous Motor," Energies, MDPI, vol. 8(9), pages 1-31, September.
    7. Jingang Yang & Yaohua Zhao & Aoxue Chen & Zhenhua Quan, 2019. "Thermal Performance of a Low-Temperature Heat Exchanger Using a Micro Heat Pipe Array," Energies, MDPI, vol. 12(4), pages 1-16, February.
    8. Seok Min Choi & Jun Su Park & Ho-Seong Sohn & Seon Ho Kim & Hyung Hee Cho, 2016. "Thermal Characteristics of Tube Bundles in Ultra-Supercritical Boilers," Energies, MDPI, vol. 9(10), pages 1-14, September.
    9. Mladen Bošnjaković & Robert Santa & Marko Katinić, 2023. "Experimental Testing of a Water-to-Water Heat Pump with and without IHX by Using Refrigerants R1234yf and R1234ze(E)," Sustainability, MDPI, vol. 15(11), pages 1-28, May.
    10. Shehryar Ishaque & Man-Hoe Kim, 2019. "Seasonal Performance Investigation for Residential Heat Pump System with Different Outdoor Heat Exchanger Designs," Energies, MDPI, vol. 12(24), pages 1-22, December.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:21:p:7941-:d:953392. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.