IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i9p2522-d545027.html
   My bibliography  Save this article

Combustion Modes and Unsteady Characteristics during the Condition Transition of a Scramjet Combustor

Author

Listed:
  • Dongpeng Jia

    (Science and Technology on Scramjet Laboratory, College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073, China)

  • Yu Pan

    (Science and Technology on Scramjet Laboratory, College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073, China)

  • Ning Wang

    (Science and Technology on Scramjet Laboratory, College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073, China)

  • Chaoyang Liu

    (Science and Technology on Scramjet Laboratory, College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073, China)

  • Kai Yang

    (Science and Technology on Scramjet Laboratory, College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073, China)

Abstract

To investigate the combustion modes and unsteady characteristics during the condition transition of a scramjet combustor, a series of experiments were carried out under the condition of Mach 2.52 supersonic incoming flow, the corresponding stagnation pressure and temperature of which were 1.6 MPa and 1486 K, respectively. A fuel supply system that could dynamically adjust the injection pressure was adopted to simulate the condition transition stage of a scramjet. Based on the advanced combustion diagnosis technique, the transient chemiluminescence image and the wall pressure were recorded during the whole combustion process. Three typical modes of turbulent combustion occurred when the injection pressure drop gradually increased. The jet flame was stable after the condition transition when the injection pressure drop was relatively low. An unstable combustion phenomenon accompanied by intermittent local extinction and reignition could be found near the blowout limits. With a further increase in the injection pressure drop, the flame was blown out quickly during the transition process. In addition, the flame development characteristics during condition transition under stable combustion mode and the effect of injection pressure drop were studied in detail. During the process of switching between the two conditions, the area and light intensity of the flame decreased over time, and the wall pressure was accordingly reduced. As the increase in injection pressure dropped, the intensity of chemical reactions deceased obviously and the transition time became longer.

Suggested Citation

  • Dongpeng Jia & Yu Pan & Ning Wang & Chaoyang Liu & Kai Yang, 2021. "Combustion Modes and Unsteady Characteristics during the Condition Transition of a Scramjet Combustor," Energies, MDPI, vol. 14(9), pages 1-14, April.
  • Handle: RePEc:gam:jeners:v:14:y:2021:i:9:p:2522-:d:545027
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/9/2522/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/14/9/2522/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Seung-Min Jeong & Jeong-Yeol Choi, 2020. "Combined Diagnostic Analysis of Dynamic Combustion Characteristics in a Scramjet Engine," Energies, MDPI, vol. 13(15), pages 1-21, August.
    2. Stephen M. Neill & Apostolos Pesyridis, 2017. "Modeling of Supersonic Combustion Systems for Sustained Hypersonic Flight," Energies, MDPI, vol. 10(11), pages 1-22, November.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Byeong-Jo Hwang & Seongki Min, 2023. "Numerical Investigation of the Effect of Supersonic Air Temperature on the Mixing Characteristics of Liquid Fuel," Energies, MDPI, vol. 16(1), pages 1-17, January.
    2. Sasha Veeran & Apostolos Pesyridis & Lionel Ganippa, 2018. "Ramjet Compression System for a Hypersonic Air Transportation Vehicle Combined Cycle Engine," Energies, MDPI, vol. 11(10), pages 1-22, September.
    3. Dongpeng Jia & Ning Wang & Yu Pan & Chaoyang Liu & Shiwei Wang & Kai Yang & Jian Liu, 2021. "Flow and Heat Transfer Characteristics of Supercritical N-Decane in Adjacent Cooling Channels with Opposite Flow Directions," Energies, MDPI, vol. 14(4), pages 1-19, February.
    4. Devendra Sen & Apostolos Pesyridis & Andrew Lenton, 2018. "A Scramjet Compression System for Hypersonic Air Transportation Vehicle Combined Cycle Engines," Energies, MDPI, vol. 11(6), pages 1-32, June.
    5. Liuyi Jiang & Hong Zhang & Qingquan Duan & Xiaoben Liu, 2021. "Numerical Simulation of Acoustic Resonance Enhancement for Mean Flow Wind Energy Harvester as Well as Suppression for Pipeline," Energies, MDPI, vol. 14(6), pages 1-17, March.
    6. Andrew Ridgway & Ashish Alex Sam & Apostolos Pesyridis, 2018. "Modelling a Hypersonic Single Expansion Ramp Nozzle of a Hypersonic Aircraft through Parametric Studies," Energies, MDPI, vol. 11(12), pages 1-29, December.
    7. Fan Li & Mingbo Sun & Zun Cai & Yong Chen & Yongchao Sun & Fei Li & Jiajian Zhu, 2020. "Effects of Additional Cavity Floor Injection on the Ignition and Combustion Processes in a Mach 2 Supersonic Flow," Energies, MDPI, vol. 13(18), pages 1-17, September.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:9:p:2522-:d:545027. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.