IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i21p7353-d672527.html
   My bibliography  Save this article

Numerical Studies of the Dynamics of the Roadheader Equipped with an Automatic Control System during Cutting of Rocks with Different Mechanical Properties

Author

Listed:
  • Piotr Cheluszka

    (Department of Mining Mechanization and Robotisation, Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, 44-100 Gliwice, Poland)

Abstract

The process of cutting rocks with a boom-type roadheader results in extreme dynamic loads and vibrations. Mining, especially in the case of hard rocks, is associated with large energy consumption, which, when combined with low process efficiency, can lead to low drilling performance. These phenomena are undesirable because excessive dynamic load leads to low machine durability, as well as deterioration of work conditions and safety. Low mining efficiency affects the economics of mining works conducted using roadheaders. However, these adverse effects can be minimized by optimizing the cutting process, thanks to the automatic control of the roadheader. The present article discusses the concept of automatic control of a boom-type roadheader’s cutting heads movement. Based on previously conducted computer investigations, it was assumed that reducing the energy consumption of the cutting process and improving the dynamic state of the roadheader (objective functions) are possible only by controlling three of the four parameters characterizing the cutting process: angular speed of the cutting heads, boom swinging speed, and cut height. The web of cut and workability of the rock can be treated as variables of a stochastic nature. This paper presents selected results of computer tests during simulated cutting of rocks with different uniaxial compressive strengths (UCS) in automatic and manual mode. In addition, the tests studied the behavior of the roadheader during the cutting of rocks with variable workability, which is typical of drilling excavations in a layered rock mass. The results of simulated cutting in automatic and manual mode were compared to assess the effectiveness of the adopted automatic control strategy. It was found that the algorithm developed for automatic control of the cutting heads’ movement allows reducing the consumption of cutting energy by up to half compared to the consumption during cutting in manual mode. Furthermore, it was found to improve the dynamic state of the machine.

Suggested Citation

  • Piotr Cheluszka, 2021. "Numerical Studies of the Dynamics of the Roadheader Equipped with an Automatic Control System during Cutting of Rocks with Different Mechanical Properties," Energies, MDPI, vol. 14(21), pages 1-29, November.
    • Handle: RePEc:gam:jeners:v:14:y:2021:i:21:p:7353-:d:672527
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/21/7353/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/14/21/7353/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Piotr Cheluszka, 2020. "Optimization of the Cutting Process Parameters to Ensure High Efficiency of Drilling Tunnels and Use the Technical Potential of the Boom-Type Roadheader," Energies, MDPI, vol. 13(24), pages 1-23, December.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Krzysztof Krauze & Kamil Mucha & Tomasz Wydro & Edward Pieczora, 2021. "Functional and Operational Requirements to Be Fulfilled by Conical Picks Regarding Their Wear Rate and Investment Costs," Energies, MDPI, vol. 14(12), pages 1-19, June.
    2. Jarosław Joostberens & Arkadiusz Pawlikowski & Dariusz Prostański & Krzysztof Nieśpiałowski, 2021. "Method for Assessment of Operation of Analog Filters Installed in the Measuring Lines for Electrical Quantities of a Mining Machine’s Converter Power Supply System," Energies, MDPI, vol. 14(9), pages 1-15, April.
    3. Łukasz Bołoz & Witold Biały, 2022. "Methods and Test Benches for Cutting Tools Testing—A Review," Energies, MDPI, vol. 16(1), pages 1-17, December.
    4. Xiaodong Ji & Minjun Zhang & Yuanyuan Qu & Hai Jiang & Miao Wu, 2021. "Travel Dynamics Analysis and Intelligent Path Rectification Planning of a Roadheader on a Roadway," Energies, MDPI, vol. 14(21), pages 1-21, November.
    5. Krzysztof Krauze & Kamil Mucha & Tomasz Wydro & Ryszard Klempka, 2022. "Assessment of the Structure of Cutting Heads with Regard to the Mining Machine Load Using Proprietary Software," Energies, MDPI, vol. 15(19), pages 1-22, September.
    6. Piotr Cheluszka & Eryk Remiorz & Jamal Rostami, 2022. "The Use of a Roadheader Simulator in Research of Dynamics and Energy-Consumption of Excavating Underground Roadways and Tunnels," Energies, MDPI, vol. 15(18), pages 1-25, September.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:21:p:7353-:d:672527. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.