IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v13y2020i11p2834-d366491.html
   My bibliography  Save this article

Industrial Ceramic Blocks for Buildings: Clay Characterization and Drying Experimental Study

Author

Listed:
  • A.M. Vasconcelos da Silva

    (Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil)

  • J.M.P.Q. Delgado

    (CONSTRUCT-LFC, Department of Civil Engineering, Faculty of Engineering, University of Porto, 4200-465 Porto, Portugal)

  • A.S. Guimarães

    (CONSTRUCT-LFC, Department of Civil Engineering, Faculty of Engineering, University of Porto, 4200-465 Porto, Portugal)

  • W.M.P. Barbosa de Lima

    (Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil)

  • R. Soares Gomez

    (Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil)

  • R. Pereira de Farias

    (Department of Agriculture Science, State University of Paraiba, Catolé do Rocha 58884-000, Brazil)

  • E. Santana de Lima

    (Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil)

  • A.G. Barbosa de Lima

    (Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil)

Abstract

The conformation of a ceramic piece follows the steps of preparing the raw material, molding, lamination, drying, and firing. Drying is a thermodynamic process of heat and mass transfer, with dimensional variations of the product that requires a large amount of energy. Ceramic materials when exposed to non-uniform drying may suffer cracks and deformations, reducing their post-drying quality. Thus, this work aimed to study the drying of industrial ceramic blocks in an oven with forced air circulation. Experiments were carried out to characterize the clay and drying of the ceramic block at temperatures ranging from 50 °C to 100 °C. Results of the chemical, mineralogical, granulometric, differential thermal, and thermogravimetric analysis of the clay, and heating kinetics, mass loss, and dimensional variation of the industrial ceramic block are presented and analyzed in detail. It was found that the clay is basically composed of silica and alumina (≈ 80.96%), with an average particle diameter of 13.36 μm. The study proved that drying at high temperature and low relative humidity of the air generates high rates of mass loss, heating, and volumetric shrinkage in the ceramic product, and high thermo-hydraulic stresses, which cause the appearance and propagation of cracks, gaps, and cleavages, compromising the final quality of the product.

Suggested Citation

  • A.M. Vasconcelos da Silva & J.M.P.Q. Delgado & A.S. Guimarães & W.M.P. Barbosa de Lima & R. Soares Gomez & R. Pereira de Farias & E. Santana de Lima & A.G. Barbosa de Lima, 2020. "Industrial Ceramic Blocks for Buildings: Clay Characterization and Drying Experimental Study," Energies, MDPI, vol. 13(11), pages 1-22, June.
  • Handle: RePEc:gam:jeners:v:13:y:2020:i:11:p:2834-:d:366491
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/13/11/2834/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/13/11/2834/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Ricardo S. Gomez & Túlio R. N. Porto & Hortência L. F. Magalhães & Gicelia Moreira & Anastácia M. M. C. N. André & Ruth B. F. Melo & Antonio G. B. Lima, 2019. "Natural Gas Intermittent Kiln for the Ceramic Industry: A Transient Thermal Analysis," Energies, MDPI, vol. 12(8), pages 1-29, April.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Elisiane S. Lima & João M. P. Q. Delgado & Ana S. Guimarães & Wanderson M. P. B. Lima & Ivonete B. Santos & Josivanda P. Gomes & Rosilda S. Santos & Anderson F. Vilela & Arianne D. Viana & Genival S. , 2021. "Drying and Heating Processes in Arbitrarily Shaped Clay Materials Using Lumped Phenomenological Modeling," Energies, MDPI, vol. 14(14), pages 1-25, July.
    2. Ricardo S. Gomez & Kelly C. Gomes & José M. A. M. Gurgel & Laís B. Alves & Hortência L. F. Magalhães & Raíssa A. Queiroga & Gustavo C. P. Sousa & Aline S. Oliveira & Anderson F. Vilela & Bruna T. A. S, 2023. "Investigating the Drying Process of Ceramic Sanitary Ware at Low Temperature," Energies, MDPI, vol. 16(10), pages 1-20, May.
    3. Stephane K. B. M. Silva & Carlos J. Araújo & João M. P. Q. Delgado & Ricardo S. Gomez & Hortência L. F. Magalhães & Maria J. Figueredo & Juliana A. Figueirôa & Mirenia K. T. Brito & José N. O. Neto & , 2022. "Heat and Mass Transfer in Structural Ceramic Blocks: An Analytical and Phenomenological Approach," Energies, MDPI, vol. 15(19), pages 1-16, September.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Václav Kočí & Lenka Scheinherrová & Jiří Maděra & Martin Keppert & Zbigniew Suchorab & Grzegorz Łagód & Robert Černý, 2020. "Experimental and Computational Study of Thermal Processes in Red Clays Exposed to High Temperatures," Energies, MDPI, vol. 13(9), pages 1-15, May.
    2. Miguel Castro Oliveira & Muriel Iten & Pedro L. Cruz & Helena Monteiro, 2020. "Review on Energy Efficiency Progresses, Technologies and Strategies in the Ceramic Sector Focusing on Waste Heat Recovery," Energies, MDPI, vol. 13(22), pages 1-24, November.
    3. Iván D. Palacio-Caro & Pedro N. Alvarado-Torres & Luis F. Cardona-Sepúlveda, 2020. "Numerical Simulation of the Flow and Heat Transfer in an Electric Steel Tempering Furnace," Energies, MDPI, vol. 13(14), pages 1-22, July.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:13:y:2020:i:11:p:2834-:d:366491. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.