IDEAS home Printed from https://ideas.repec.org/a/gam/jagris/v12y2022i6p775-d826528.html
   My bibliography  Save this article

Research and Experiment on the Removal Mechanism of Light Impurities of the Residual Mulch Film Recovery Machine

Author

Listed:
  • Peng Wang

    (College of Mechanical and Electrical Engineering, Shihezi University, Shihezi 832000, China
    Xinjiang Uygur Autonomous Region Research Institute of Measurement & Testing, Wulumuqi 830011, China)

  • Xuegeng Chen

    (College of Mechanical and Electrical Engineering, Shihezi University, Shihezi 832000, China
    Key Laboratory of Northwest Agricultural Equipment, Ministry of Agriculture and Rural Affairs, Shihezi 832000, China)

  • Haojun Wen

    (College of Mechanical and Electrical Engineering, Shihezi University, Shihezi 832000, China
    Key Laboratory of Northwest Agricultural Equipment, Ministry of Agriculture and Rural Affairs, Shihezi 832000, China)

Abstract

Aiming at the problem of high impurity rate in the recycled residual film, combined with the existing installation (4JMLE-210 agricultural residual film recycling machine), the removal mechanism of light impurities on the film surface was analyzed. The statics and kinematics analysis of light impurity particles in different spatial positions were carried out to determine the conditions for the movement of impurity particles. By analyzing critical conditions, such as ideal collision and throwing capacity, the structural dimensions of the straight pipe section and its outlet section were determined. Using Origin 2018 software, the movement track of the impurity particles left from the upper and lower limit positions and the ideal curve of the throwing arc were plotted, and the trapezoidal section was determined at the outlet of the throwing arc section. Finally, trial-produce prototype, and a field test was carried out on the performance of the machine by selecting the impurity rate in the recovered residual film as the test index. The results showed that when the forward speed of the machine and the rotating speed of the cutter roll were in the range of 5.4–5.8 km/h and 1440–1460 r·min −1 , the light impurity rate and working efficiency could keep a good balance. The light impurity rate in the recovered residual film was between 10.9% and 31.4%, and the average light impurity rate was around 18.7%, which met the design and application requirements.

Suggested Citation

  • Peng Wang & Xuegeng Chen & Haojun Wen, 2022. "Research and Experiment on the Removal Mechanism of Light Impurities of the Residual Mulch Film Recovery Machine," Agriculture, MDPI, vol. 12(6), pages 1-16, May.
  • Handle: RePEc:gam:jagris:v:12:y:2022:i:6:p:775-:d:826528
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2077-0472/12/6/775/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2077-0472/12/6/775/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Zhiyuan Zhang & Jingbin Li & Xianfei Wang & Yongman Zhao & Shuaikang Xue & Zipeng Su, 2022. "Parameters Optimization and Test of an Arc-Shaped Nail-Tooth Roller-Type Recovery Machine for Sowing Layer Residual Film," Agriculture, MDPI, vol. 12(5), pages 1-14, May.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Peng Wang & Xuegeng Chen & Haojun Wen, 2023. "Simulation Research on Cotton Stalk Cutting and Crushing Based on ANSYS/LS-DYNA and Field Experiments," Agriculture, MDPI, vol. 13(6), pages 1-24, June.
    2. Deli Jiang & Xuegeng Chen & Limin Yan & Haixiao Gou & Jiacheng Yang & Ying Li, 2023. "Parameter Calibration of Discrete Element Model for Cotton Rootstalk–Soil Mixture at Harvest Stage in Xinjiang Cotton Field," Agriculture, MDPI, vol. 13(7), pages 1-17, July.
    3. Mengyu Guo & Bin Hu & Xin Luo & Chenglin Yuan & Yiquan Cai & Luochuan Xu, 2023. "Design and Test of a Sliding Cutting Device for the Plastic Mulch Waste," Sustainability, MDPI, vol. 15(5), pages 1-18, March.
    4. Can Hu & Zhengxin Xu & Xufeng Wang & Long Wang & Jianfei Xing & Wensong Guo, 2022. "Experimental Study on Optimal Recycling Mechanical Parameters of Cotton Field Mulch film based on Small Soil Trough System," Agriculture, MDPI, vol. 12(7), pages 1-15, July.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Bingcheng Zhang & Rongqing Liang & Jiali Li & Yaping Li & Hewei Meng & Za Kan, 2022. "Test and Analysis on Friction Characteristics of Major Cotton Stalk Cultivars in Xinjiang," Agriculture, MDPI, vol. 12(7), pages 1-13, June.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jagris:v:12:y:2022:i:6:p:775-:d:826528. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.