IDEAS home Printed from https://ideas.repec.org/a/eee/renene/v62y2014icp285-292.html
   My bibliography  Save this article

Empirical estimation of regenerator efficiency for a low temperature differential Stirling engine

Author

Listed:
  • Kato, Yoshitaka
  • Baba, Kazunari

Abstract

An experimental method of regenerator evaluation is proposed in this paper. The configuration of the experimental equipment used in the method is similar to that of an alpha-configuration Stirling engine with a phase angle of 180°. The temperature of the hot side heat exchanger is controlled by an electric heater, and the heat sink was room air. An air conditioner controlled the temperature of the room air. The temperature and pressure of the working fluid were measured during the piston motion. A #18 stainless steel mesh was used as a regenerator matrix for a low temperature differential Stirling engine (LTDSE). The regenerator efficiency can be calculated based on the measurement results. The product of the swept volume, the density of the working fluid, the specific heat and the difference in the working fluid temperatures between the hot side and the cold side is greater than the amount of the internal energy fluctuation. The reason for this is assumed to be the temperature fluctuation in the region between the two heat exchangers. The walls of the region are made of acrylic resin. The amount of the temperature fluctuation in the region is assumed to be uniform. The regenerator efficiency is calculated as a function of the temperature fluctuation in the region. The evaluation method does not require a fast-response thermocouple. The prediction of the regenerator efficiency is possible basted on some experimental results of same matrix. Polyurethane foam and #18 stainless steel mesh, layered parallel to the stream line of the working fluid, were each tested. These materials can realize a non-rectangular regenerator without the generation of waste. Non-rectangular regenerator includes regenerator that can be installed into narrow gaps. The regenerator efficiency of the stainless steel mesh layered parallel to the stream line of the working fluid was significantly less in comparison to that of the normal mesh layers. In the polyurethane foam case, a pressure loss was observed.

Suggested Citation

  • Kato, Yoshitaka & Baba, Kazunari, 2014. "Empirical estimation of regenerator efficiency for a low temperature differential Stirling engine," Renewable Energy, Elsevier, vol. 62(C), pages 285-292.
    • Handle: RePEc:eee:renene:v:62:y:2014:i:c:p:285-292
    DOI: 10.1016/j.renene.2013.07.023
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0960148113003686
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.renene.2013.07.023?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Kongtragool, Bancha & Wongwises, Somchai, 2007. "Performance of low-temperature differential Stirling engines," Renewable Energy, Elsevier, vol. 32(4), pages 547-566.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Wu, Zhanghua & Chen, Yanyan & Dai, Wei & Luo, Ercang & Li, Donghui, 2015. "Investigation on the thermoacoustic conversion characteristic of regenerator," Applied Energy, Elsevier, vol. 152(C), pages 156-161.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Karabulut, Halit & Yücesu, Hüseyin Serdar & ÇInar, Can & Aksoy, Fatih, 2009. "An experimental study on the development of a [beta]-type Stirling engine for low and moderate temperature heat sources," Applied Energy, Elsevier, vol. 86(1), pages 68-73, January.
    2. Karabulut, H. & Çınar, C. & Oztürk, E. & Yücesu, H.S., 2010. "Torque and power characteristics of a helium charged Stirling engine with a lever controlled displacer driving mechanism," Renewable Energy, Elsevier, vol. 35(1), pages 138-143.
    3. Cheng, Chin-Hsiang & Yang, Hang-Suin, 2011. "Analytical model for predicting the effect of operating speed on shaft power output of Stirling engines," Energy, Elsevier, vol. 36(10), pages 5899-5908.
    4. Kato, Yoshitaka, 2016. "Indicated diagrams of a low temperature differential Stirling engine using flat plates as heat exchangers," Renewable Energy, Elsevier, vol. 85(C), pages 973-980.
    5. Wang, Kai & Sanders, Seth R. & Dubey, Swapnil & Choo, Fook Hoong & Duan, Fei, 2016. "Stirling cycle engines for recovering low and moderate temperature heat: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 62(C), pages 89-108.
    6. Li, Ruijie & Grosu, Lavinia & Li, Wei, 2017. "New polytropic model to predict the performance of beta and gamma type Stirling engine," Energy, Elsevier, vol. 128(C), pages 62-76.
    7. Jacek Kropiwnicki & Mariusz Furmanek, 2020. "A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines," Energies, MDPI, vol. 13(7), pages 1-21, April.
    8. Parlak, Nezaket & Wagner, Andreas & Elsner, Michael & Soyhan, Hakan S., 2009. "Thermodynamic analysis of a gamma type Stirling engine in non-ideal adiabatic conditions," Renewable Energy, Elsevier, vol. 34(1), pages 266-273.
    9. Sripakagorn, Angkee & Srikam, Chana, 2011. "Design and performance of a moderate temperature difference Stirling engine," Renewable Energy, Elsevier, vol. 36(6), pages 1728-1733.
    10. Araoz, Joseph A. & Salomon, Marianne & Alejo, Lucio & Fransson, Torsten H., 2015. "Numerical simulation for the design analysis of kinematic Stirling engines," Applied Energy, Elsevier, vol. 159(C), pages 633-650.
    11. Cheng, Chin-Hsiang & Yang, Hang-Suin, 2012. "Optimization of geometrical parameters for Stirling engines based on theoretical analysis," Applied Energy, Elsevier, vol. 92(C), pages 395-405.
    12. Ahmadi, Mohammad H. & Ahmadi, Mohammad Ali & Sadatsakkak, Seyed Abbas & Feidt, Michel, 2015. "Connectionist intelligent model estimates output power and torque of stirling engine," Renewable and Sustainable Energy Reviews, Elsevier, vol. 50(C), pages 871-883.
    13. Wang, Jia & Xu, Weiqing & Ding, Shuiting & Shi, Yan & Cai, Maolin & Rehman, Ali, 2015. "Liquid air fueled open-closed cycle Stirling engine and its exergy analysis," Energy, Elsevier, vol. 90(P1), pages 187-201.
    14. Hua-Ju Shih, 2019. "An Analysis Model Combining Gamma-Type Stirling Engine and Power Converter," Energies, MDPI, vol. 12(7), pages 1-18, April.
    15. Tavakolpour-Saleh, A.R. & Jokar, H., 2016. "Neural network-based control of an intelligent solar Stirling pump," Energy, Elsevier, vol. 94(C), pages 508-523.
    16. Karabulut, Halit & Aksoy, Fatih & Öztürk, Erkan, 2009. "Thermodynamic analysis of a β type Stirling engine with a displacer driving mechanism by means of a lever," Renewable Energy, Elsevier, vol. 34(1), pages 202-208.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:renene:v:62:y:2014:i:c:p:285-292. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/renewable-energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.