IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v233-234y2019ip156-169.html
   My bibliography  Save this article

Critical assessment of oxy-fuel integrated coal gasification combined cycles

Author

Listed:
  • Ishii, Hiromi
  • Hayashi, Tomoya
  • Tada, Hiroaki
  • Yokohama, Katsuhiko
  • Takashima, Ryuhei
  • Hayashi, Jun-ichiro

Abstract

Critical assessment was performed for a type of oxy-fuel integrated coal gasification combined cycles (IGCC) that was comprised of proven components. A type of two-stage entrained-flow gasifier consisting of combustor and reductor sections was simulated by a one-dimensional model that has been proven through application to gasifiers of industrial scales. It was successfully reproduced on Aspen Plus® and integrated together with the other components into a commercial-scale IGCC system. The oxidizing agents were not only O2 and CO2 (carrier gas for conveying the coal) but also additional CO2 or CO2/H2O, that was required to suppress hydrocarbons formation and maintain the combustor temperature allowing molten ash to have sufficiently low viscosity. The net thermal efficiency was predicted as a function of steam/coal mass ratio (S/C) within a range of 0–0.4. Increasing S/C up to 0.2 increased the cold gas efficiency slightly but resulted in decrease in the net thermal efficiency of the system. This was mainly due to the extraction of steam from the high pressure steam turbine exhaust, causing loss of power output. Resulting in lower cold gas efficiency due to higher oxygen ratio, higher moisture content of the pulverized coal gave higher net thermal efficiency due to less steam consumption for coal drying. The net efficiency was optimized at approximately 39% on a higher-heating-value basis without steam feeding, which was higher by 6–7 points than that for conventional IGCC with oxygen-blown gasification combined with CO2 recovery.

Suggested Citation

  • Ishii, Hiromi & Hayashi, Tomoya & Tada, Hiroaki & Yokohama, Katsuhiko & Takashima, Ryuhei & Hayashi, Jun-ichiro, 2019. "Critical assessment of oxy-fuel integrated coal gasification combined cycles," Applied Energy, Elsevier, vol. 233, pages 156-169.
    • Handle: RePEc:eee:appene:v:233-234:y:2019:i::p:156-169
    DOI: 10.1016/j.apenergy.2018.10.021
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261918315691
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2018.10.021?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Kobayashi, Makoto & Akiho, Hiroyuki & Nakao, Yoshinobu, 2015. "Performance evaluation of porous sodium aluminate sorbent for halide removal process in oxy-fuel IGCC power generation plant," Energy, Elsevier, vol. 92(P3), pages 320-327.
    2. Kunze, Christian & Spliethoff, Hartmut, 2012. "Assessment of oxy-fuel, pre- and post-combustion-based carbon capture for future IGCC plants," Applied Energy, Elsevier, vol. 94(C), pages 109-116.
    3. Zhao, Yongming & Zhao, Lifeng & Wang, Bo & Zhang, Shijie & Chi, Jinling & Xiao, Yunhan, 2018. "Thermodynamic analysis of a novel dual expansion coal-fueled direct-fired supercritical carbon dioxide power cycle," Applied Energy, Elsevier, vol. 217(C), pages 480-495.
    4. Watanabe, Hiroaki & Ahn, Seongyool & Tanno, Kenji, 2017. "Numerical investigation of effects of CO2 recirculation in an oxy-fuel IGCC on gasification characteristics of a two-stage entrained flow coal gasifier," Energy, Elsevier, vol. 118(C), pages 181-189.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Xu, Ming-Xin & Wu, Hai-Bo & Wu, Ya-Chang & Wang, Han-Xiao & Ouyang, Hao-Dong & Lu, Qiang, 2021. "Design and evaluation of a novel system for the flue gas compression and purification from the oxy-fuel combustion process," Applied Energy, Elsevier, vol. 285(C).
    2. Igor Donskoy, 2023. "Techno-Economic Efficiency Estimation of Promising Integrated Oxyfuel Gasification Combined-Cycle Power Plants with Carbon Capture," Clean Technol., MDPI, vol. 5(1), pages 1-18, February.
    3. Sterkhov, K.V. & Khokhlov, D.A. & Zaichenko, M.N., 2024. "Zero carbon emission CCGT power plant with integrated solid fuel gasification," Energy, Elsevier, vol. 294(C).
    4. David Berstad & Geir Skaugen & Simon Roussanaly & Rahul Anantharaman & Petter Nekså & Kristin Jordal & Stian Trædal & Truls Gundersen, 2022. "CO 2 Capture from IGCC by Low-Temperature Synthesis Gas Separation," Energies, MDPI, vol. 15(2), pages 1-24, January.
    5. Ding, Jing & Wang, Yarong & Gu, Rong & Wang, Weilong & Lu, Jianfeng, 2019. "Thermochemical storage performance of methane reforming with carbon dioxide using high temperature slag," Applied Energy, Elsevier, vol. 250(C), pages 1270-1279.
    6. Sun, Enhui & Ji, Hongfu & Wang, Xiangren & Ma, Wenjing & Zhang, Lei & Xu, Jinliang, 2023. "Proposal of multistage mass storage process to approach isothermal heat rejection of semi-closed S–CO2 cycle," Energy, Elsevier, vol. 270(C).
    7. Kim, Mukyeong & Ye, Insoo & Jo, Hyunbin & Ryu, Changkook & Kim, Bongkeun & Lee, Jeongsoo, 2020. "New reduced-order model optimized for online dynamic simulation of a Shell coal gasifier," Applied Energy, Elsevier, vol. 263(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Moioli, Stefania & Giuffrida, Antonio & Romano, Matteo C. & Pellegrini, Laura A. & Lozza, Giovanni, 2016. "Assessment of MDEA absorption process for sequential H2S removal and CO2 capture in air-blown IGCC plants," Applied Energy, Elsevier, vol. 183(C), pages 1452-1470.
    2. Kobayashi, Makoto & Akiho, Hiroyuki & Ozawa, Yasushi & Nakajima, Akira, 2019. "Verification of proper operation of dry acid gas removal process on syngas derived by O2/CO2-blown gasifier," Applied Energy, Elsevier, vol. 252(C), pages 1-1.
    3. Kobayashi, Makoto & Akiho, Hiroyuki & Nakao, Yoshinobu, 2015. "Performance evaluation of porous sodium aluminate sorbent for halide removal process in oxy-fuel IGCC power generation plant," Energy, Elsevier, vol. 92(P3), pages 320-327.
    4. Lee, Sung-Wook & Park, Jong-Soo & Lee, Chun-Boo & Lee, Dong-Wook & Kim, Hakjoo & Ra, Ho Won & Kim, Sung-Hyun & Ryi, Shin-Kun, 2014. "H2 recovery and CO2 capture after water–gas shift reactor using synthesis gas from coal gasification," Energy, Elsevier, vol. 66(C), pages 635-642.
    5. Xu, Shisen & Ren, Yongqiang & Wang, Baomin & Xu, Yue & Chen, Liang & Wang, Xiaolong & Xiao, Tiancun, 2014. "Development of a novel 2-stage entrained flow coal dry powder gasifier," Applied Energy, Elsevier, vol. 113(C), pages 318-323.
    6. Igor Donskoy, 2023. "Techno-Economic Efficiency Estimation of Promising Integrated Oxyfuel Gasification Combined-Cycle Power Plants with Carbon Capture," Clean Technol., MDPI, vol. 5(1), pages 1-18, February.
    7. Prabu, V. & Geeta, K., 2015. "CO2 enhanced in-situ oxy-coal gasification based carbon-neutral conventional power generating systems," Energy, Elsevier, vol. 84(C), pages 672-683.
    8. Michalski, Sebastian & Hanak, Dawid P. & Manovic, Vasilije, 2020. "Advanced power cycles for coal-fired power plants based on calcium looping combustion: A techno-economic feasibility assessment," Applied Energy, Elsevier, vol. 269(C).
    9. Zhang, Minkai & Guo, Yincheng, 2013. "Rate based modeling of absorption and regeneration for CO2 capture by aqueous ammonia solution," Applied Energy, Elsevier, vol. 111(C), pages 142-152.
    10. Li, Shiyuan & Li, Haoyu & Li, Wei & Xu, Mingxin & Eddings, Eric G. & Ren, Qiangqiang & Lu, Qinggang, 2017. "Coal combustion emission and ash formation characteristics at high oxygen concentration in a 1MWth pilot-scale oxy-fuel circulating fluidized bed," Applied Energy, Elsevier, vol. 197(C), pages 203-211.
    11. Ganapathy, Harish & Steinmayer, Sascha & Shooshtari, Amir & Dessiatoun, Serguei & Ohadi, Michael M. & Alshehhi, Mohamed, 2016. "Process intensification characteristics of a microreactor absorber for enhanced CO2 capture," Applied Energy, Elsevier, vol. 162(C), pages 416-427.
    12. Álvarez, L. & Gharebaghi, M. & Jones, J.M. & Pourkashanian, M. & Williams, A. & Riaza, J. & Pevida, C. & Pis, J.J. & Rubiera, F., 2013. "CFD modeling of oxy-coal combustion: Prediction of burnout, volatile and NO precursors release," Applied Energy, Elsevier, vol. 104(C), pages 653-665.
    13. Georgios Varvoutis & Athanasios Lampropoulos & Evridiki Mandela & Michalis Konsolakis & George E. Marnellos, 2022. "Recent Advances on CO 2 Mitigation Technologies: On the Role of Hydrogenation Route via Green H 2," Energies, MDPI, vol. 15(13), pages 1-38, June.
    14. Oh, Se-Young & Binns, Michael & Cho, Habin & Kim, Jin-Kuk, 2016. "Energy minimization of MEA-based CO2 capture process," Applied Energy, Elsevier, vol. 169(C), pages 353-362.
    15. Imtiaz, Qasim & Broda, Marcin & Müller, Christoph R., 2014. "Structure–property relationship of co-precipitated Cu-rich, Al2O3- or MgAl2O4-stabilized oxygen carriers for chemical looping with oxygen uncoupling (CLOU)," Applied Energy, Elsevier, vol. 119(C), pages 557-565.
    16. Xin, Tuantuan & Xu, Cheng & Yang, Yongping & Kindra, Vladimir & Rogalev, Andrey, 2023. "A new process splitting analytical method for the coal-based Allam cycle: Thermodynamic assessment and process integration," Energy, Elsevier, vol. 267(C).
    17. Ziębik, Andrzej & Malik, Tomasz & Liszka, Marcin, 2015. "Thermodynamic evaluation of CHP (combined heat and power) plants integrated with installations of coal gasification," Energy, Elsevier, vol. 92(P2), pages 179-188.
    18. Perejón, Antonio & Romeo, Luis M. & Lara, Yolanda & Lisbona, Pilar & Martínez, Ana & Valverde, Jose Manuel, 2016. "The Calcium-Looping technology for CO2 capture: On the important roles of energy integration and sorbent behavior," Applied Energy, Elsevier, vol. 162(C), pages 787-807.
    19. Chowdhury, A.S.M. Arifur & Bugarin, Luz & Badhan, Antara & Choudhuri, Ahsan & Love, Norman, 2016. "Thermodynamic analysis of a directly heated oxyfuel supercritical power system," Applied Energy, Elsevier, vol. 179(C), pages 261-271.
    20. Wu, Zeyang & Liu, Sen & Gao, Hongxia & Yin, Qiqi & Liang, Zhiwu, 2019. "A study of structure-activity relationships of aqueous diamine solutions with low heat of regeneration for post-combustion CO2 capture," Energy, Elsevier, vol. 167(C), pages 359-368.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:233-234:y:2019:i::p:156-169. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.