IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v111y2013icp16-27.html
   My bibliography  Save this article

The use of variable speed drives for cost-effective energy savings in South African mine cooling systems

Author

Listed:
  • Du Plessis, Gideon Edgar
  • Liebenberg, Leon
  • Mathews, Edward Henry

Abstract

An industrial energy efficiency improvement through the introduction of modern technology is an important demand-side management initiative. Cooling systems on South African mines have been identified as large electricity consumers. There is significant potential for energy efficiency improvement by the widespread introduction of variable speed drive (VSD) technology. An energy audit was conducted on 20 large mine cooling systems and potential savings and feasibility indicators were calculated. A pilot implementation study was also done on one mine to experimentally validate the estimated savings. In this paper, the results of the audit, the potential savings and the pilot study results are presented. It is shown that large-scale implementation of VSDs on mine cooling system pumps and fans is economically viable. A total annual electrical energy saving of 144,721MWh, or 32.2%, can be achieved. An annual cost saving of US$6,938,148 and CO2 emissions reduction of 132Mton is possible. The implementation of VSDs on mine chiller compressors will also result in large energy savings, but is not economically feasible at present. Results of the pilot study indicate an electricity savings of 29.9%. The results are important to decision makers and indicate the significant impact that widespread VSD usage on mine cooling systems can have on South African mine sustainability.

Suggested Citation

  • Du Plessis, Gideon Edgar & Liebenberg, Leon & Mathews, Edward Henry, 2013. "The use of variable speed drives for cost-effective energy savings in South African mine cooling systems," Applied Energy, Elsevier, vol. 111(C), pages 16-27.
    • Handle: RePEc:eee:appene:v:111:y:2013:i:c:p:16-27
    DOI: 10.1016/j.apenergy.2013.04.061
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261913003577
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2013.04.061?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Thirugnanasambandam, M. & Hasanuzzaman, M. & Saidur, R. & Ali, M.B. & Rajakarunakaran, S. & Devaraj, D. & Rahim, N.A., 2011. "Analysis of electrical motors load factors and energy savings in an Indian cement industry," Energy, Elsevier, vol. 36(7), pages 4307-4314.
    2. Vosloo, Jan & Liebenberg, Leon & Velleman, Douglas, 2012. "Case study: Energy savings for a deep-mine water reticulation system," Applied Energy, Elsevier, vol. 92(C), pages 328-335.
    3. Tirmizi, Syed A. & Gandhidasan, P. & Zubair, Syed M., 2012. "Performance analysis of a chilled water system with various pumping schemes," Applied Energy, Elsevier, vol. 100(C), pages 238-248.
    4. Menyah, Kojo & Wolde-Rufael, Yemane, 2010. "Energy consumption, pollutant emissions and economic growth in South Africa," Energy Economics, Elsevier, vol. 32(6), pages 1374-1382, November.
    5. Odhiambo, Nicholas M., 2009. "Electricity consumption and economic growth in South Africa: A trivariate causality test," Energy Economics, Elsevier, vol. 31(5), pages 635-640, September.
    6. Zhang, Shirong & Xia, Xiaohua, 2010. "Optimal control of operation efficiency of belt conveyor systems," Applied Energy, Elsevier, vol. 87(6), pages 1929-1937, June.
    7. Zhuan, Xiangtao & Xia, Xiaohua, 2013. "Optimal operation scheduling of a pumping station with multiple pumps," Applied Energy, Elsevier, vol. 104(C), pages 250-257.
    8. McKane, Aimee & Hasanbeigi, Ali, 2011. "Motor systems energy efficiency supply curves: A methodology for assessing the energy efficiency potential of industrial motor systems," Energy Policy, Elsevier, vol. 39(10), pages 6595-6607, October.
    9. Hasanuzzaman, M. & Rahim, N.A. & Saidur, R. & Kazi, S.N., 2011. "Energy savings and emissions reductions for rewinding and replacement of industrial motor," Energy, Elsevier, vol. 36(1), pages 233-240.
    10. de Almeida, Aníbal T & Fonseca, Paula & Bertoldi, Paolo, 2003. "Energy-efficient motor systems in the industrial and in the services sectors in the European Union: characterisation, potentials, barriers and policies," Energy, Elsevier, vol. 28(7), pages 673-690.
    11. Amusa, Hammed & Amusa, Kafayat & Mabugu, Ramos, 2009. "Aggregate demand for electricity in South Africa: An analysis using the bounds testing approach to cointegration," Energy Policy, Elsevier, vol. 37(10), pages 4167-4175, October.
    12. Reimer, Jeffrey J. & Hill, Lowell D., 2003. "Designing U.S. Corn Grades to Reflect End Use Value," Journal of Agricultural and Applied Economics, Cambridge University Press, vol. 35(1), pages 15-28, April.
    13. Mecrow, B.C. & Jack, A.G., 2008. "Efficiency trends in electric machines and drives," Energy Policy, Elsevier, vol. 36(12), pages 4336-4341, December.
    14. Bennett, M. & Newborough, M., 2001. "Auditing energy use in cities," Energy Policy, Elsevier, vol. 29(2), pages 125-134, January.
    15. Sebitosi, A.B. & Pillay, P., 2008. "Grappling with a half-hearted policy: The case of renewable energy and the environment in South Africa," Energy Policy, Elsevier, vol. 36(7), pages 2513-2516, July.
    16. du Plessis, Gideon Edgar & Liebenberg, Leon & Mathews, Edward Henry, 2013. "Case study: The effects of a variable flow energy saving strategy on a deep-mine cooling system," Applied Energy, Elsevier, vol. 102(C), pages 700-709.
    17. Inglesi-Lotz, Roula & Blignaut, James N., 2011. "South Africa’s electricity consumption: A sectoral decomposition analysis," Applied Energy, Elsevier, vol. 88(12), pages 4779-4784.
    18. Abdelaziz, E.A. & Saidur, R. & Mekhilef, S., 2011. "A review on energy saving strategies in industrial sector," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(1), pages 150-168, January.
    19. Saidur, R. & Rahim, N.A. & Hasanuzzaman, M., 2010. "A review on compressed-air energy use and energy savings," Renewable and Sustainable Energy Reviews, Elsevier, vol. 14(4), pages 1135-1153, May.
    20. Imhotep P. Alagidede & Tamara E. Mughogho, 2019. "Capital Account Liberalization and Capital Flows to Sub-Saharan Africa: A Panel Threshold Approach," Working Papers 203, Economic Research Southern Africa.
    21. Zhang, Shirong & Xia, Xiaohua, 2011. "Modeling and energy efficiency optimization of belt conveyors," Applied Energy, Elsevier, vol. 88(9), pages 3061-3071.
    22. Saidur, R. & Hasanuzzaman, M. & Mahlia, T.M.I. & Rahim, N.A. & Mohammed, H.A., 2011. "Chillers energy consumption, energy savings and emission analysis in an institutional buildings," Energy, Elsevier, vol. 36(8), pages 5233-5238.
    23. Harald Winkler & Meagan Jooste & Andrew Marquard, 2010. "Structuring approaches to pricing carbon in energy- and trade-intensive sectors in South Africa," Climate Policy, Taylor & Francis Journals, vol. 10(5), pages 527-542, September.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Ünal, Berat Berkan & Onaygil, Sermin & Acuner, Ebru & Cin, Rabia, 2022. "Application of energy efficiency obligation scheme for electricity distribution companies in Turkey," Energy Policy, Elsevier, vol. 163(C).
    2. Wang, Zhiyuan & Qian, Zhongdong & Lu, Jie & Wu, Pengfei, 2019. "Effects of flow rate and rotational speed on pressure fluctuations in a double-suction centrifugal pump," Energy, Elsevier, vol. 170(C), pages 212-227.
    3. Xian Li & Houli Fu, 2020. "Development of an Efficient Cooling Strategy in the Heading Face of Underground Mines," Energies, MDPI, vol. 13(5), pages 1-11, March.
    4. Zuberi, M. Jibran S. & Tijdink, Anton & Patel, Martin K., 2017. "Techno-economic analysis of energy efficiency improvement in electric motor driven systems in Swiss industry," Applied Energy, Elsevier, vol. 205(C), pages 85-104.
    5. Xu, Wei & Chen, Genglin & Shi, Huijin & Zhang, Pengcheng & Chen, Xuemei, 2023. "Research on operational characteristics of coal power centrifugal fans at off-design working conditions based on flap-angle adjustment," Energy, Elsevier, vol. 284(C).
    6. Chatterjee, Arnab & Zhang, Lijun & Xia, Xiaohua, 2015. "Optimization of mine ventilation fan speeds according to ventilation on demand and time of use tariff," Applied Energy, Elsevier, vol. 146(C), pages 65-73.
    7. Arun Shankar, Vishnu Kalaiselvan & Umashankar, Subramaniam & Paramasivam, Shanmugam & Hanigovszki, Norbert, 2016. "A comprehensive review on energy efficiency enhancement initiatives in centrifugal pumping system," Applied Energy, Elsevier, vol. 181(C), pages 495-513.
    8. Chen, Yi & Yan, Huaxia & Yang, Hongxing, 2018. "Comparative study of on-off control and novel high-low control of regenerative indirect evaporative cooler (RIEC)," Applied Energy, Elsevier, vol. 225(C), pages 233-243.
    9. Junqiao Li & Yucheng Li & Wei Zhang & Jinyang Dong & Yunan Cui, 2022. "Multi-Objective Intelligent Decision and Linkage Control Algorithm for Mine Ventilation," Energies, MDPI, vol. 15(21), pages 1-17, October.
    10. Prince, & Hati, Ananda Shankar, 2021. "A comprehensive review of energy-efficiency of ventilation system using Artificial Intelligence," Renewable and Sustainable Energy Reviews, Elsevier, vol. 146(C).
    11. Trianni, Andrea & Cagno, Enrico & Accordini, Davide, 2019. "Energy efficiency measures in electric motors systems: A novel classification highlighting specific implications in their adoption," Applied Energy, Elsevier, vol. 252(C), pages 1-1.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Prince, & Hati, Ananda Shankar, 2021. "A comprehensive review of energy-efficiency of ventilation system using Artificial Intelligence," Renewable and Sustainable Energy Reviews, Elsevier, vol. 146(C).
    2. Muller, C.J. & Craig, I.K., 2016. "Energy reduction for a dual circuit cooling water system using advanced regulatory control," Applied Energy, Elsevier, vol. 171(C), pages 287-295.
    3. Burgos Payán, Manuel & Roldan Fernandez, Juan Manuel & Maza Ortega, Jose Maria & Riquelme Santos, Jesus Manuel, 2019. "Techno-economic optimal power rating of induction motors," Applied Energy, Elsevier, vol. 240(C), pages 1031-1048.
    4. Habib, Mohammad Ahsan & Hasanuzzaman, M. & Hosenuzzaman, M. & Salman, Asif & Mehadi, Md Riyad, 2016. "Energy consumption, energy saving and emission reduction of a garment industrial building in Bangladesh," Energy, Elsevier, vol. 112(C), pages 91-100.
    5. Bohlmann, Jessika Andreina & Inglesi-Lotz, Roula, 2018. "Analysing the South African residential sector's energy profile," Renewable and Sustainable Energy Reviews, Elsevier, vol. 96(C), pages 240-252.
    6. Roula Inglesi-Lotz, 2012. "The sensitivity of the South African industrial sector’s electricity consumption to electricity price fluctuations," Working Papers 201225, University of Pretoria, Department of Economics.
    7. Cabello Eras, Juan José & Sagastume Gutiérrez, Alexis & Sousa Santos, Vladimir & Cabello Ulloa, Mario Javier, 2020. "Energy management of compressed air systems. Assessing the production and use of compressed air in industry," Energy, Elsevier, vol. 213(C).
    8. Ahmed, Ferdous & Al Amin, Abul Quasem & Hasanuzzaman, M. & Saidur, R., 2013. "Alternative energy resources in Bangladesh and future prospect," Renewable and Sustainable Energy Reviews, Elsevier, vol. 25(C), pages 698-707.
    9. Trianni, Andrea & Cagno, Enrico & Accordini, Davide, 2019. "Energy efficiency measures in electric motors systems: A novel classification highlighting specific implications in their adoption," Applied Energy, Elsevier, vol. 252(C), pages 1-1.
    10. Sauer, Ildo L. & Tatizawa, Hédio & Salotti, Francisco A.M. & Mercedes, Sonia S., 2015. "A comparative assessment of Brazilian electric motors performance with minimum efficiency standards," Renewable and Sustainable Energy Reviews, Elsevier, vol. 41(C), pages 308-318.
    11. Yoon, Hae-Sung & Kim, Eun-Seob & Kim, Min-Soo & Lee, Jang-Yeob & Lee, Gyu-Bong & Ahn, Sung-Hoon, 2015. "Towards greener machine tools – A review on energy saving strategies and technologies," Renewable and Sustainable Energy Reviews, Elsevier, vol. 48(C), pages 870-891.
    12. Thirugnanasambandam, M. & Hasanuzzaman, M. & Saidur, R. & Ali, M.B. & Rajakarunakaran, S. & Devaraj, D. & Rahim, N.A., 2011. "Analysis of electrical motors load factors and energy savings in an Indian cement industry," Energy, Elsevier, vol. 36(7), pages 4307-4314.
    13. Lin, Boqiang & Moubarak, Mohamed, 2014. "Estimation of energy saving potential in China's paper industry," Energy, Elsevier, vol. 65(C), pages 182-189.
    14. Hosain, Md Lokman & Bel Fdhila, Rebei & Rönnberg, Kristian, 2017. "Taylor-Couette flow and transient heat transfer inside the annulus air-gap of rotating electrical machines," Applied Energy, Elsevier, vol. 207(C), pages 624-633.
    15. Monyei, C.G. & Adewumi, A.O., 2017. "Demand Side Management potentials for mitigating energy poverty in South Africa," Energy Policy, Elsevier, vol. 111(C), pages 298-311.
    16. Hasanuzzaman, M. & Rahim, N.A. & Hosenuzzaman, M. & Saidur, R. & Mahbubul, I.M. & Rashid, M.M., 2012. "Energy savings in the combustion based process heating in industrial sector," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(7), pages 4527-4536.
    17. Zuberi, M. Jibran S. & Tijdink, Anton & Patel, Martin K., 2017. "Techno-economic analysis of energy efficiency improvement in electric motor driven systems in Swiss industry," Applied Energy, Elsevier, vol. 205(C), pages 85-104.
    18. Trianni, Andrea & Cagno, Enrico & De Donatis, Alessio, 2014. "A framework to characterize energy efficiency measures," Applied Energy, Elsevier, vol. 118(C), pages 207-220.
    19. Nehler, Therese, 2018. "Linking energy efficiency measures in industrial compressed air systems with non-energy benefits – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 89(C), pages 72-87.
    20. Arun Shankar, Vishnu Kalaiselvan & Umashankar, Subramaniam & Paramasivam, Shanmugam & Hanigovszki, Norbert, 2016. "A comprehensive review on energy efficiency enhancement initiatives in centrifugal pumping system," Applied Energy, Elsevier, vol. 181(C), pages 495-513.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:111:y:2013:i:c:p:16-27. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.