IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v16y2023i5p2132-d1076893.html
   My bibliography  Save this article

Impact of the Evaporation Temperature on the Air Drying Rate for a Finned Heat Exchanger

Author

Listed:
  • Tomasz Mołczan

    (Faculty of Mechanical Engineering, Cracow University of Technology, al. Jana Pawla II 37, 31-864 Cracow, Poland)

  • Piotr Cyklis

    (Faculty of Mechanical Engineering, Cracow University of Technology, al. Jana Pawla II 37, 31-864 Cracow, Poland)

Abstract

This paper presents the thermal calculations of an air-finned heat exchanger working at temperatures above zero degrees and their verification through testing on a real device. Then, on the basis of the calculations, the influence of evaporation temperature on the drying rate of the constant speed of air flowing through the exchanger was analysed. A quantitative analysis of the effect of the temperature difference between the air being dried and the evaporator on the acceleration of the process was performed. For the analysed case, the same water mass (condensate) can be obtained for an evaporation temperature of 0 °C almost four times faster than for 10 °C. To compare temperature cases, the SMER (specific moisture evaporation ratio) was calculated, which allowed the systems to be compared in terms of energy consumption. The theoretical analysis showed that by reducing the boiling point by 10 degrees, we could increase the SMER from 0.51 kg h 2 0 / kWh to 2.18 kg h 2 0 / kWh . After receiving the experimental results and including the efficiency of the system, these values were, respectively, 0.44 ± 0.01 kg h 2 0 / kWh and 1.91 ± 0.06 kg h 2 0 / kWh .

Suggested Citation

  • Tomasz Mołczan & Piotr Cyklis, 2023. "Impact of the Evaporation Temperature on the Air Drying Rate for a Finned Heat Exchanger," Energies, MDPI, vol. 16(5), pages 1-14, February.
    • Handle: RePEc:gam:jeners:v:16:y:2023:i:5:p:2132-:d:1076893
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/16/5/2132/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/16/5/2132/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Tomasz Mołczan & Piotr Cyklis, 2022. "Mathematical Model of Air Dryer Heat Pump Exchangers," Energies, MDPI, vol. 15(19), pages 1-23, September.
    2. Rezk, Kamal & Forsberg, Jan, 2011. "Geometry development of the internal duct system of a heat pump tumble dryer based on fluid mechanic parameters from a CFD software," Applied Energy, Elsevier, vol. 88(5), pages 1596-1605, May.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. De Bellis, Fabio & Catalano, Luciano A., 2012. "CFD optimization of an immersed particle heat exchanger," Applied Energy, Elsevier, vol. 97(C), pages 841-848.
    2. Gungor, Aysegul & Erbay, Zafer & Hepbasli, Arif, 2011. "Exergoeconomic analyses of a gas engine driven heat pump drier and food drying process," Applied Energy, Elsevier, vol. 88(8), pages 2677-2684, August.
    3. Bansal, Pradeep & Mohabir, Amar & Miller, William, 2016. "A novel method to determine air leakage in heat pump clothes dryers," Energy, Elsevier, vol. 96(C), pages 1-7.
    4. Konstantin Osintsev & Sergei Aliukov & Sulpan Kuskarbekova & Tatyana Tarasova & Aleksandr Karelin & Vladimir Konchakov & Olga Kornyakova, 2023. "Increasing Thermal Efficiency: Methods, Case Studies, and Integration of Heat Exchangers with Renewable Energy Sources and Heat Pumps for Desalination," Energies, MDPI, vol. 16(13), pages 1-36, June.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:16:y:2023:i:5:p:2132-:d:1076893. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.