IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v16y2023i3p1191-d1043277.html
   My bibliography  Save this article

Development and Research of a Promising Pumpless Liquid Cooling System for Reciprocating Compressors

Author

Listed:
  • V. E. Shcherba

    (Fluid Mechanics and Transport Machines Section, Omsk State Technical University, 644050 Omsk, Russia)

  • A. Khait

    (Department of Mechanical Engineering & Mechatronics, Faculty of Engineering, Ariel University, Ariel 40700, Israel)

  • E. A. Pavlyuchenko

    (Fluid Mechanics and Transport Machines Section, Omsk State Technical University, 644050 Omsk, Russia)

  • I. Yu. Bulgakova

    (Fluid Mechanics and Transport Machines Section, Omsk State Technical University, 644050 Omsk, Russia)

Abstract

A new pumpless liquid cooling system for a single-stage two-cylinder reciprocating compressor has been developed from the analysis of work processes and cooling systems of reciprocating compressors, where one piston compresses and moves gas and coolant in the cooling system. The intensification of the coolant movement increases in the machine, which can reduce the temperature of the cylinder–piston group and increase the indicator efficiency and the compressor feed rate. A mathematical model of working processes in a reciprocating compressor and its cooling system has been developed on the basic fundamental laws of conservation of energy, mass and motion. A prototype was developed and tested to obtain new knowledge about the processes in the machine and confirm the assumptions made while developing the mathematical model. After a series of experiments, the influence of cooling on the working processes in a reciprocating compressor, the technical work carried out in each working process, the energy and consumption characteristics of a reciprocating compressor with a developed cooling system were established. There was a validation performed of the developed mathematical model of work processes in the machine and the assumptions made. According to the developed mathematical model of work processes, a numerical experiment was carried out, which established: the coolant flow rate decreases with an increase in discharge pressure and increases with an increase in the crankshaft speed when the discharge pressure changes from 0.4 MPa to 0.8 MPa, a decrease in the indicator isothermal efficiency due to the leakage and non-isothermal nature of the compression process, as well as a decrease in the return work in the process of reverse expansion, leading to a decrease in the indicator isothermal efficiency of more than 15%; due to the equalization of pressures in the gas cavities with an increase in discharge pressure, the coolant consumption is reduced by (15 ± 17)%; with an increase in the angular speed of the crankshaft from 800 rpm to 1500 rpm, the coolant flow rate increases by more than 2.5 times, this increase in coolant flow rate is due to an increase in hydraulic resistance due to an increase in gas velocity; in the range from 1000 to 1200 rpm, a maximum of the indicator isothermal efficiency and compressor feed rate is observed; maximum indicator isothermal efficiency and the supply ratio is observed at a coolant flow rate in the range from 800 mL/min to 900 mL/min.

Suggested Citation

  • V. E. Shcherba & A. Khait & E. A. Pavlyuchenko & I. Yu. Bulgakova, 2023. "Development and Research of a Promising Pumpless Liquid Cooling System for Reciprocating Compressors," Energies, MDPI, vol. 16(3), pages 1-26, January.
    • Handle: RePEc:gam:jeners:v:16:y:2023:i:3:p:1191-:d:1043277
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/16/3/1191/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/16/3/1191/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Muhammad Kamran Alam & Khadija Bibi & Aamir Khan & Unai Fernandez-Gamiz & Samad Noeiaghdam, 2022. "The Effect of Variable Magnetic Field on Viscous Fluid between 3-D Rotatory Vertical Squeezing Plates: A Computational Investigation," Energies, MDPI, vol. 15(7), pages 1-21, March.
    2. Qin, Chao & Loth, Eric, 2014. "Liquid piston compression efficiency with droplet heat transfer," Applied Energy, Elsevier, vol. 114(C), pages 539-550.
    3. Van de Ven, James D. & Li, Perry Y., 2009. "Liquid piston gas compression," Applied Energy, Elsevier, vol. 86(10), pages 2183-2191, October.
    4. Borys Basok & Vyacheslav Kremnev & Anatoliy Pavlenko & Andriy Timoshchenko, 2022. "Aerodynamics and Complicated Heat Transfer with the Mixed Motion of Air in the Flat Duct of a High-Temperature Heat Exchanger," Energies, MDPI, vol. 15(3), pages 1-17, January.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Yan, Bo & Wieberdink, Jacob & Shirazi, Farzad & Li, Perry Y. & Simon, Terrence W. & Van de Ven, James D., 2015. "Experimental study of heat transfer enhancement in a liquid piston compressor/expander using porous media inserts," Applied Energy, Elsevier, vol. 154(C), pages 40-50.
    2. He, Wei & Wang, Jihong, 2018. "Optimal selection of air expansion machine in Compressed Air Energy Storage: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 87(C), pages 77-95.
    3. Wieberdink, Jacob & Li, Perry Y. & Simon, Terrence W. & Van de Ven, James D., 2018. "Effects of porous media insert on the efficiency and power density of a high pressure (210 bar) liquid piston air compressor/expander – An experimental study," Applied Energy, Elsevier, vol. 212(C), pages 1025-1037.
    4. Zhang, Xinjing & Xu, Yujie & Zhou, Xuezhi & Zhang, Yi & Li, Wen & Zuo, Zhitao & Guo, Huan & Huang, Ye & Chen, Haisheng, 2018. "A near-isothermal expander for isothermal compressed air energy storage system," Applied Energy, Elsevier, vol. 225(C), pages 955-964.
    5. Bennett, Jeffrey A. & Simpson, Juliet G. & Qin, Chao & Fittro, Roger & Koenig, Gary M. & Clarens, Andres F. & Loth, Eric, 2021. "Techno-economic analysis of offshore isothermal compressed air energy storage in saline aquifers co-located with wind power," Applied Energy, Elsevier, vol. 303(C).
    6. Siraj Sabihuddin & Aristides E. Kiprakis & Markus Mueller, 2014. "A Numerical and Graphical Review of Energy Storage Technologies," Energies, MDPI, vol. 8(1), pages 1-45, December.
    7. Patil, Vikram C. & Acharya, Pinaki & Ro, Paul I., 2020. "Experimental investigation of water spray injection in liquid piston for near-isothermal compression," Applied Energy, Elsevier, vol. 259(C).
    8. Gouda, El Mehdi & Benaouicha, Mustapha & Neu, Thibault & Fan, Yilin & Luo, Lingai, 2022. "Flow and heat transfer characteristics of air compression in a liquid piston for compressed air energy storage," Energy, Elsevier, vol. 254(PB).
    9. Huan Guo & Haoyuan Kang & Yujie Xu & Mingzhi Zhao & Yilin Zhu & Hualiang Zhang & Haisheng Chen, 2023. "Review of Coupling Methods of Compressed Air Energy Storage Systems and Renewable Energy Resources," Energies, MDPI, vol. 16(12), pages 1-22, June.
    10. Huang, Shucheng & Khajepour, Amir, 2022. "A new adiabatic compressed air energy storage system based on a novel compression strategy," Energy, Elsevier, vol. 242(C).
    11. Budt, Marcus & Wolf, Daniel & Span, Roland & Yan, Jinyue, 2016. "A review on compressed air energy storage: Basic principles, past milestones and recent developments," Applied Energy, Elsevier, vol. 170(C), pages 250-268.
    12. Aliaga, D.M. & Romero, C.P. & Feick, R. & Brooks, W.K. & Campbell, A.N., 2024. "Modelling, simulation, and optimisation of a novel liquid piston system for energy recovery," Applied Energy, Elsevier, vol. 357(C).
    13. Zhang, Yufei & Jin, Peng & Wang, Haiyang & Cai, Xuchao & Ge, Gangqiang & Chen, Hao & Wang, Huanran & Li, Ruixiong, 2024. "Dimensionless thermal performance analysis of a closed isothermal compressed air energy storage system with spray-enhanced heat transfer," Energy, Elsevier, vol. 307(C).
    14. Aliaga, D.M. & Romero, C.P. & Feick, R. & Brooks, W.K. & Campbell, A.N., 2024. "Modelling and simulation of a novel liquid air energy storage system with a liquid piston, NH3 and CO2 cycles for enhanced heat and cold utilisation," Applied Energy, Elsevier, vol. 362(C).
    15. Gao, Ziyu & Zhang, Xinjing & Li, Xiaoyu & Xu, Yujie & Chen, Haisheng, 2023. "Thermodynamic analysis of isothermal compressed air energy storage system with droplets injection," Energy, Elsevier, vol. 284(C).
    16. Jianting Sun & Xin Zhou & Qi Liang & Zhitao Zuo & Haisheng Chen, 2019. "The Effect of Wet Compression on a Centrifugal Compressor for a Compressed Air Energy Storage System," Energies, MDPI, vol. 12(5), pages 1-24, March.
    17. Qin, Chao & Innes-Wimsatt, Elijah & Loth, Eric, 2016. "Hydraulic-electric hybrid wind turbines: Tower mass saving and energy storage capacity," Renewable Energy, Elsevier, vol. 99(C), pages 69-79.
    18. Guo, Huan & Xu, Yujie & Kang, Haoyuan & Guo, Wenbing & Liu, Yu & Zhang, Xinjing & Zhou, Xuezhi & Chen, Haisheng, 2023. "From theory to practice: Evaluating the thermodynamic design landscape of compressed air energy storage systems," Applied Energy, Elsevier, vol. 352(C).
    19. Semmari, Hamza & Stitou, Driss & Mauran, Sylvain, 2012. "A novel Carnot-based cycle for ocean thermal energy conversion," Energy, Elsevier, vol. 43(1), pages 361-375.
    20. Semmari, Hamza & Mauran, Sylvain & Stitou, Driss, 2017. "Experimental validation of an analytical model of hydraulic motor operating under variable electrical loads and pressure heads," Applied Energy, Elsevier, vol. 206(C), pages 1309-1320.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:16:y:2023:i:3:p:1191-:d:1043277. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.