IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i22p8660-d976961.html
   My bibliography  Save this article

Heat Transfer in 3D Laguerre–Voronoi Open-Cell Foams under Pulsating Flow

Author

Listed:
  • Aidar Khairullin

    (Energy Supply of Enterprises, Construction of Buildings and Structures, Kazan State Power Engineering University, 51 Krasnoselskaya Street, 420066 Kazan, Russia)

  • Aigul Haibullina

    (Energy Supply of Enterprises, Construction of Buildings and Structures, Kazan State Power Engineering University, 51 Krasnoselskaya Street, 420066 Kazan, Russia)

  • Alex Sinyavin

    (Energy Supply of Enterprises, Construction of Buildings and Structures, Kazan State Power Engineering University, 51 Krasnoselskaya Street, 420066 Kazan, Russia)

  • Denis Balzamov

    (Energy Supply of Enterprises, Construction of Buildings and Structures, Kazan State Power Engineering University, 51 Krasnoselskaya Street, 420066 Kazan, Russia)

  • Vladimir Ilyin

    (Energy Supply of Enterprises, Construction of Buildings and Structures, Kazan State Power Engineering University, 51 Krasnoselskaya Street, 420066 Kazan, Russia)

  • Liliya Khairullina

    (Engineering Institute of Computer Mathematics and Information Technologies, Kazan Federal University, 18 Kremlyovskaya Street, 420008 Kazan, Russia)

  • Veronika Bronskaya

    (Engineering Institute of Computer Mathematics and Information Technologies, Kazan Federal University, 18 Kremlyovskaya Street, 420008 Kazan, Russia
    Mechanical Faculty, Kazan National Research Technological University, 68 Karl Marx Street, 420015 Kazan, Russia)

Abstract

Open-cell foams are attractive for heat transfer enhancement in many engineering applications. Forced pulsations can lead to additional heat transfer enhancement in porous media. Studies of heat transfer in open-cell foams under forced pulsation conditions are limited. Therefore, in this work, the possibility of heat transfer enhancement in porous media with flow pulsations is studied by a numerical simulation. To generate the 3D open-cell foams, the Laguerre–Voronoi tessellation method was used. The foam porosity was 0.743, 0.864, and 0.954. The Reynolds numbers ranged from 10 to 55, and the products of the relative amplitude and the Strouhal numbers ranged from 0.114 to 0.344. Heat transfer was studied under the conditions of symmetric and asymmetric pulsations. The results of numerical simulation showed that an increase in the amplitude of pulsations led to an augmentation of heat transfer for all studied porosities. The maximum intensification of heat transfer was 43%. Symmetric pulsations were more efficient than asymmetric pulsations, with Reynolds numbers less than 25. The Thermal Performance Factor was always higher for asymmetric pulsations, due to the friction factor for symmetrical pulsations being much higher than for asymmetric pulsations. Based on the results of a numerical simulation, empirical correlations were obtained to predict the heat transfer intensification in porous media for a steady and pulsating flow.

Suggested Citation

  • Aidar Khairullin & Aigul Haibullina & Alex Sinyavin & Denis Balzamov & Vladimir Ilyin & Liliya Khairullina & Veronika Bronskaya, 2022. "Heat Transfer in 3D Laguerre–Voronoi Open-Cell Foams under Pulsating Flow," Energies, MDPI, vol. 15(22), pages 1-26, November.
    • Handle: RePEc:gam:jeners:v:15:y:2022:i:22:p:8660-:d:976961
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/22/8660/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/15/22/8660/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Aigul Haibullina & Aidar Khairullin & Denis Balzamov & Vladimir Ilyin & Veronika Bronskaya & Liliya Khairullina, 2022. "Local Heat Transfer Dynamics in the In-Line Tube Bundle under Asymmetrical Pulsating Flow," Energies, MDPI, vol. 15(15), pages 1-24, July.
    2. Cha-Lee Myung & Juwon Kim & Wonwook Jang & Dongyoung Jin & Simsoo Park & Jeongmin Lee, 2015. "Nanoparticle Filtration Characteristics of Advanced Metal Foam Media for a Spark Ignition Direct Injection Engine in Steady Engine Operating Conditions and Vehicle Test Modes," Energies, MDPI, vol. 8(3), pages 1-17, March.
    3. Trilok G & Kurma Eshwar Sai Srinivas & Devika Harikrishnan & Gnanasekaran N & Moghtada Mobedi, 2022. "Correlations and Numerical Modeling of Stacked Woven Wire-Mesh Porous Media for Heat Exchange Applications," Energies, MDPI, vol. 15(7), pages 1-25, March.
    4. Roman Dyga & Sebastian Brol, 2021. "Pressure Drops in Two-Phase Gas–Liquid Flow through Channels Filled with Open-Cell Metal Foams," Energies, MDPI, vol. 14(9), pages 1-26, April.
    5. Ali A. Hmad & Nihad Dukhan, 2021. "Cooling Design for PEM Fuel-Cell Stacks Employing Air and Metal Foam: Simulation and Experiment," Energies, MDPI, vol. 14(9), pages 1-19, May.
    6. Nihad Dukhan, 2021. "Equivalent Parallel Strands Modeling of Highly-Porous Media for Two-Dimensional Heat Transfer: Application to Metal Foam," Energies, MDPI, vol. 14(19), pages 1-18, October.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Hossein Pourrahmani & Hamed Shakeri & Jan Van herle, 2022. "Thermoelectric Generator as the Waste Heat Recovery Unit of Proton Exchange Membrane Fuel Cell: A Numerical Study," Energies, MDPI, vol. 15(9), pages 1-21, April.
    2. Jerzy Hapanowicz & Adriana Szydłowska & Jacek Wydrych, 2022. "Experimental and Prenemilary Numerical Evaluation of Pressure Drops under the Conditions of the Stratified Gas-Liquid Flow in a Horizontal Pipe Filled with Metal Foam," Energies, MDPI, vol. 15(23), pages 1-22, November.
    3. Jinxi Zhou & Song Zhou & Yuanqing Zhu, 2017. "Characterization of Particle and Gaseous Emissions from Marine Diesel Engines with Different Fuels and Impact of After-Treatment Technology," Energies, MDPI, vol. 10(8), pages 1-14, July.
    4. Rawal Diganjit & N. Gnanasekaran & Moghtada Mobedi, 2022. "Numerical Study for Enhancement of Heat Transfer Using Discrete Metal Foam with Varying Thickness and Porosity in Solar Air Heater by LTNE Method," Energies, MDPI, vol. 15(23), pages 1-28, November.
    5. Mingfei Mu & Xinghu Li & Yong Qiu & Yang Shi, 2019. "Study on a New Gasoline Particulate Filter Structure Based on the Nested Cylinder and Diversion Channel Plug," Energies, MDPI, vol. 12(11), pages 1-19, May.
    6. Ercelik, Mustafa & Ismail, Mohammed S. & Ingham, Derek B. & Hughes, Kevin J. & Ma, Lin & Pourkashanian, Mohamed, 2023. "Efficient X-ray CT-based numerical computations of structural and mass transport properties of nickel foam-based GDLs for PEFCs," Energy, Elsevier, vol. 262(PB).
    7. Hanbing Ke & Xuzhi Zhou & Tao Liu & Yu Wang & Hui Wang, 2023. "Numerical Study of Heat and Mass Transfer in the Original Structure and Homogeneous Substitution Model for Three Dimensional Porous Metal Foam," Energies, MDPI, vol. 16(3), pages 1-12, January.
    8. Khalifa Aliyu Ibrahim & Patrick Luk & Zhenhua Luo, 2023. "Cooling of Concentrated Photovoltaic Cells—A Review and the Perspective of Pulsating Flow Cooling," Energies, MDPI, vol. 16(6), pages 1-23, March.
    9. Wei Wang & Liang Ding & Fangming Han & Yong Shuai & Bingxi Li & Bengt Sunden, 2022. "Parametric Study on Thermo-Hydraulic Performance of NACA Airfoil Fin PCHEs Channels," Energies, MDPI, vol. 15(14), pages 1-15, July.
    10. Caket, Ahmet Guray & Wang, Chunyang & Nugroho, Marvel Alif & Celik, Hasan & Mobedi, Moghtada, 2022. "Recent studies on 3D lattice metal frame technique for enhancement of heat transfer: Discovering trends and reasons," Renewable and Sustainable Energy Reviews, Elsevier, vol. 167(C).
    11. Mingfei Mu & Jonas Sjöblom & Henrik Ström & Xinghu Li, 2019. "Analysis of the Flow Field from Connection Cones to Monolith Reactors," Energies, MDPI, vol. 12(3), pages 1-20, January.
    12. Mingfei Mu & Jonas Sjöblom & Nikhil Sharma & Henrik Ström & Xinghu Li, 2019. "Experimental Study on the Flow Field of Particles Deposited on a Gasoline Particulate Filter," Energies, MDPI, vol. 12(14), pages 1-18, July.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:22:p:8660-:d:976961. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.