IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i20p6659-d656398.html
   My bibliography  Save this article

Experimental and Numerical Study of Multiple Jets Impinging a Step Surface

Author

Listed:
  • Flavia V. Barbosa

    (MEtRICs I&D Centre, School of Engineering, University of Minho, 4800-058 Guimarães, Portugal)

  • Senhorinha F. C. F. Teixeira

    (ALGORITMI I&D Centre, School of Engineering, University of Minho, 4800-058 Guimarães, Portugal)

  • José C. F. Teixeira

    (MEtRICs I&D Centre, School of Engineering, University of Minho, 4800-058 Guimarães, Portugal)

Abstract

Multiple jet impingement is a widely implemented convective process for enhancing heat transfer over target surfaces. Depending on the engineering application, the impinging plate can have different configurations. However, the increased complexity of the surface induces complicated thermal behaviors that must be analyzed. In that sense, this study consisted of the experimental and numerical analysis of multiple jets impinging on a step surface. A particle image velocimetry technique was applied to measure velocity fields, while a heat flux sensor was mounted on the surface to determine the heat transfer. Numerical simulations, for both flat and non-flat plates, were conducted in ANSYS FLUENT applying the SST k-ω model, and experimental results were used to validate the model. Three surface configurations were analyzed, flat, 1 D , and 2 D steps, and the results show an increase in the average Nusselt number compared with the flat plate, 9% and 20%, respectively. This increase was mainly due to the intensification of the flow turbulence induced by the step. Numerical results were in good agreement with the experiments, but the heat transfer was slightly underpredicted for the 2 D step case due to the difficulty of predicting with accuracy the velocity field near the step.

Suggested Citation

  • Flavia V. Barbosa & Senhorinha F. C. F. Teixeira & José C. F. Teixeira, 2021. "Experimental and Numerical Study of Multiple Jets Impinging a Step Surface," Energies, MDPI, vol. 14(20), pages 1-23, October.
  • Handle: RePEc:gam:jeners:v:14:y:2021:i:20:p:6659-:d:656398
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/20/6659/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/14/20/6659/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Abdulrahman H. Alenezi & Abdulrahman Almutairi & Hamad M. Alhajeri & Abdulmajid Addali & Abdelaziz A. A. Gamil, 2018. "Flow Structure and Heat Transfer of Jet Impingement on a Rib-Roughened Flat Plate," Energies, MDPI, vol. 11(6), pages 1-16, June.
    2. Marcos André de Oliveira & Paulo Guimarães de Moraes & Crystianne Lilian de Andrade & Alex Mendonça Bimbato & Luiz Antonio Alcântara Pereira, 2020. "Control and Suppression of Vortex Shedding from a Slightly Rough Circular Cylinder by a Discrete Vortex Method," Energies, MDPI, vol. 13(17), pages 1-23, August.
    3. Zhong Ren & Xiaoyu Yang & Xunfeng Lu & Xueying Li & Jing Ren, 2021. "Experimental Investigation of Micro Cooling Units on Impingement Jet Array Flow Pressure Loss and Heat Transfer Characteristics," Energies, MDPI, vol. 14(16), pages 1-21, August.
    4. Myriam Slama & Camille Choma Bex & Grégory Pinon & Michael Togneri & Iestyn Evans, 2021. "Lagrangian Vortex Computations of a Four Tidal Turbine Array: An Example Based on the NEPTHYD Layout in the Alderney Race," Energies, MDPI, vol. 14(13), pages 1-23, June.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Tomasz P. Olejnik & Tymoteusz Mysakowski & Paweł Tomtas & Radosław Mostowski, 2021. "Optimization of the Beef Drying Process in a Heat Pump Chamber Dryer," Energies, MDPI, vol. 14(16), pages 1-21, August.
    2. Alex Mendonça Bimbato & Luiz Antonio Alcântara Pereira & Miguel Hiroo Hirata, 2020. "Study of Surface Roughness Effect on a Bluff Body—The Formation of Asymmetric Separation Bubbles," Energies, MDPI, vol. 13(22), pages 1-20, November.
    3. Thomas Jackowski & Maximilian Elfner & Hans-Jörg Bauer & Katharina Stichling & Marco Hahn, 2021. "Experimental Study of Impingement Effusion Cooled Double-Wall Combustor Liners: Aerodynamic Analysis with Stereo-PIV," Energies, MDPI, vol. 14(19), pages 1-23, September.
    4. Wei Zhang & Huiren Zhu & Guangchao Li, 2020. "Experimental Study of Heat Transfer on the Internal Surfaces of a Double-Wall Structure with Pin Fin Array," Energies, MDPI, vol. 13(24), pages 1-17, December.
    5. Lingbo Zhu & Yiping Lu & Jianfei Tong & Tianjiao Liang & Youlian Lu & Weida Fu & Bin Wang & Yunan Zhang, 2021. "Sensitivity Analysis of Influencing Factors of Supercritical Methane Flow and Heat Transfer in a U-Tube," Energies, MDPI, vol. 14(18), pages 1-15, September.
    6. Paulo Guimarães de Moraes & Luiz Antonio Alcântara Pereira, 2021. "Surface Roughness Effects on Flows Past Two Circular Cylinders in Tandem Arrangement at Co-Shedding Regime," Energies, MDPI, vol. 14(24), pages 1-21, December.
    7. Salman, Mohammad & Park, Myeong Hyeon & Chauhan, Ranchan & Kim, Sung Chul, 2021. "Experimental analysis of single loop solar heat collector with jet impingement over indented dimples," Renewable Energy, Elsevier, vol. 169(C), pages 618-628.
    8. Sylvain S. Guillou & Eric Bibeau, 2023. "Tidal Turbines," Energies, MDPI, vol. 16(7), pages 1-5, April.
    9. Parkpoom Sriromreun & Paranee Sriromreun, 2019. "A Numerical and Experimental Investigation of Dimple Effects on Heat Transfer Enhancement with Impinging Jets," Energies, MDPI, vol. 12(5), pages 1-16, March.
    10. Ebubekir Beyazoglu & Bahadir Erman Yuce & Murat Ates & Rumeysa Yalindag & Kemal Furkan Sokmen & Erhan Pulat, 2022. "Cooling of Heated Blocks with Triangular Guide Protrusions Simulating Printed Circuit Boards," Sustainability, MDPI, vol. 14(23), pages 1-27, November.
    11. Leonid Plotnikov & Nikita Grigoriev & Leonid Osipov & Vladimir Slednev & Vladislav Shurupov, 2022. "Stationary Gas Dynamics and Heat Transfer of Turbulent Flows in Straight Pipes at Different Turbulence Intensity," Energies, MDPI, vol. 15(19), pages 1-13, October.
    12. Lili Zhang & Lei Tian & Qiong Shen & Fei Liu & Haolin Li & Zhuojun Dong & Jingyue Cheng & Haoru Liu & Jiangjun Wan, 2021. "Study on the Influence and Optimization of the Venturi Effect on the Natural Ventilation of Buildings in the Xichang Area," Energies, MDPI, vol. 14(16), pages 1-17, August.
    13. Liang Xu & Tao Yang & Yanhua Sun & Lei Xi & Jianmin Gao & Yunlong Li, 2021. "Flow and Heat Transfer Characteristics of a Swirling Impinging Jet Issuing from a Threaded Nozzle of 45 Degrees," Energies, MDPI, vol. 14(24), pages 1-26, December.
    14. Artur J. Jaworski, 2019. "Special Issue “Fluid Flow and Heat Transfer”," Energies, MDPI, vol. 12(16), pages 1-4, August.
    15. Linqi Shui & Zhongkai Hu & Hang Song & Zhi Zhai & Jiatao Wang, 2023. "Study on Flow and Heat Transfer Characteristics and Anti-Clogging Performance of Tree-Like Branching Microchannels," Energies, MDPI, vol. 16(14), pages 1-22, July.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:20:p:6659-:d:656398. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.