IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v251y2022ics0360544222006004.html
   My bibliography  Save this article

Energy, exergy, sustainability and economic analysis of waste tire pyrolysis oil blends with different nanoparticle additives in spark ignition engine

Author

Listed:
  • Yaqoob, Haseeb
  • Teoh, Yew Heng
  • Sher, Farooq
  • Jamil, Muhammad Ahmad
  • Ali, Mubbashar
  • Ağbulut, Ümit
  • Salam, Hamza Ahmad
  • Arslan, Muhammad
  • Soudagar, Manzoore Elahi M.
  • Mujtaba, M.A.
  • Elfasakhany, Ashraf
  • Afzal, Asif

Abstract

Fossil fuels are the primary source of energy for most industries worldwide. However, its resources are finite and declining day by day, and toxic gases are released due to their consumption which causes global warming and problems with the health of the living. Therefore, any alternatives to fossil fuels or any additives added to the fuel needed to be found to minimize fuel consumption and the emission of harmful gases. In this study, a spark-ignition engine fuelled with blends of petrol with different concentrations of graphite nanoparticles, Fe2O3 nanoparticles, and tire pyrolysis oil (TPO) were used to conduct energy, exergy, economic, and sustainability analyses, and the obtained results were compared with neat petrol. The blends of petrol with 40 mg/L, 80 mg/L, and 120 mg/L of graphite nanoparticles & Fe2O3 nanoparticles, as well as 5% & 10% TPO, were used in a single-cylinder, four-stroke, air-cooled SI engine in this study. The experiments were conducted on various engine loads of 2 Nm to 10 Nm with an increment of 2 Nm at a constant speed of 3500 rpm. The maximum exergy and energy efficiencies were obtained 23.05% and 21.94% at a load of 8 Nm when the testengine fired with the P120FO blend, respectively. A maximum sustainability index of 1.3 for the P120FO blend was obtained. A minimum exhaust energy rate of 0.03241 kW was obtained for P120FO. A minimum exhaust exergy rate of 0.005849 kW was obtained for P90T10. Best results in energy efficiency, exergy efficiency, sustainability index, and economic analysis were obtained for the P120FO blend compared to neat petrol. Finally, it was concluded that the addition of nanoparticles in fossil fuel increases the engine's efficiency, decreases fuel consumption, and reduces the emission of harmful gases.

Suggested Citation

  • Yaqoob, Haseeb & Teoh, Yew Heng & Sher, Farooq & Jamil, Muhammad Ahmad & Ali, Mubbashar & Ağbulut, Ümit & Salam, Hamza Ahmad & Arslan, Muhammad & Soudagar, Manzoore Elahi M. & Mujtaba, M.A. & Elfasakh, 2022. "Energy, exergy, sustainability and economic analysis of waste tire pyrolysis oil blends with different nanoparticle additives in spark ignition engine," Energy, Elsevier, vol. 251(C).
    • Handle: RePEc:eee:energy:v:251:y:2022:i:c:s0360544222006004
    DOI: 10.1016/j.energy.2022.123697
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544222006004
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2022.123697?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Ali, Mohamed Kamal Ahmed & Fuming, Peng & Younus, Hussein A. & Abdelkareem, Mohamed A.A. & Essa, F.A. & Elagouz, Ahmed & Xianjun, Hou, 2018. "Fuel economy in gasoline engines using Al2O3/TiO2 nanomaterials as nanolubricant additives," Applied Energy, Elsevier, vol. 211(C), pages 461-478.
    2. Zhu, Mingming & Ma, Yu & Zhang, Dongke, 2012. "Effect of a homogeneous combustion catalyst on the combustion characteristics and fuel efficiency in a diesel engine," Applied Energy, Elsevier, vol. 91(1), pages 166-172.
    3. Koç, Mustafa & Sekmen, Yakup & Topgül, Tolga & Yücesu, Hüseyin Serdar, 2009. "The effects of ethanol–unleaded gasoline blends on engine performance and exhaust emissions in a spark-ignition engine," Renewable Energy, Elsevier, vol. 34(10), pages 2101-2106.
    4. Man, Hanyang & Liu, Huan & Xiao, Qian & Deng, Fanyuan & Yu, Qiao & Wang, Kai & Yang, Zhengjun & Wu, Ye & He, Kebin & Hao, Jiming, 2018. "How ethanol and gasoline formula changes evaporative emissions of the vehicles," Applied Energy, Elsevier, vol. 222(C), pages 584-594.
    5. Rosen, Marc A. & Dincer, Ibrahim & Kanoglu, Mehmet, 2008. "Role of exergy in increasing efficiency and sustainability and reducing environmental impact," Energy Policy, Elsevier, vol. 36(1), pages 128-137, January.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Yu, Zhang & Ahmad, Muhammad Sajjad & Shen, Boxiong & Li, Yingna & Ibrahim, Muhammad & Bokhari, Awais & Klemeš, Jiří Jaromír, 2023. "Activated waste cotton cellulose as renewable fuel and value-added chemicals: Thermokinetic analysis, coupled pyrolysis with gas chromatography and mass spectrometry," Energy, Elsevier, vol. 283(C).
    2. Liu, Lu & Shao, Shuangquan, 2023. "Recent advances of low-temperature cascade phase change energy storage technology: A state-of-the-art review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 186(C).
    3. Wang, Yudong & Hu, Junjie, 2023. "Two-stage energy management method of integrated energy system considering pre-transaction behavior of energy service provider and users," Energy, Elsevier, vol. 271(C).
    4. Du, Jinlong & Shen, Tianhao & Hu, Jianhang & Zhang, Fengxia & Yang, Shiliang & Liu, Huili & Wang, Hua, 2023. "Study on thermochemical conversion of triglyceride biomass catalyzed by biochar catalyst," Energy, Elsevier, vol. 277(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Alvin Kiprono Bett & Saeid Jalilinasrabady, 2021. "Optimization of ORC Power Plants for Geothermal Application in Kenya by Combining Exergy and Pinch Point Analysis," Energies, MDPI, vol. 14(20), pages 1-17, October.
    2. L. Hay & A. H. B. Duffy & R. I. Whitfield, 2017. "The S‐Cycle Performance Matrix: Supporting Comprehensive Sustainability Performance Evaluation of Technical Systems," Systems Engineering, John Wiley & Sons, vol. 20(1), pages 45-70, January.
    3. Ziya Sogut, M., 2021. "New approach for assessment of environmental effects based on entropy optimization of jet engine," Energy, Elsevier, vol. 234(C).
    4. van der Kroon, Bianca & Brouwer, Roy & van Beukering, Pieter J.H., 2013. "The energy ladder: Theoretical myth or empirical truth? Results from a meta-analysis," Renewable and Sustainable Energy Reviews, Elsevier, vol. 20(C), pages 504-513.
    5. Cullen, Jonathan M. & Allwood, Julian M., 2010. "Theoretical efficiency limits for energy conversion devices," Energy, Elsevier, vol. 35(5), pages 2059-2069.
    6. Maia, Cristiana Brasil & Ferreira, André Guimarães & Cabezas-Gómez, Luben & de Oliveira Castro Silva, Janaína & de Morais Hanriot, Sérgio, 2017. "Thermodynamic analysis of the drying process of bananas in a small-scale solar updraft tower in Brazil," Renewable Energy, Elsevier, vol. 114(PB), pages 1005-1012.
    7. Suiuay, Chokchai & Laloon, Kittipong & Katekaew, Somporn & Senawong, Kritsadang & Noisuwan, Phakamat & Sudajan, Somposh, 2020. "Effect of gasoline-like fuel obtained from hard-resin of Yang (Dipterocarpus alatus) on single cylinder gasoline engine performance and exhaust emissions," Renewable Energy, Elsevier, vol. 153(C), pages 634-645.
    8. Najafi, Gholamhassan & Ghobadian, Barat & Yusaf, Talal & Safieddin Ardebili, Seyed Mohammad & Mamat, Rizalman, 2015. "Optimization of performance and exhaust emission parameters of a SI (spark ignition) engine with gasoline–ethanol blended fuels using response surface methodology," Energy, Elsevier, vol. 90(P2), pages 1815-1829.
    9. Soltanian, Salman & Kalogirou, Soteris A. & Ranjbari, Meisam & Amiri, Hamid & Mahian, Omid & Khoshnevisan, Benyamin & Jafary, Tahereh & Nizami, Abdul-Sattar & Gupta, Vijai Kumar & Aghaei, Siavash & Pe, 2022. "Exergetic sustainability analysis of municipal solid waste treatment systems: A systematic critical review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 156(C).
    10. Baskut, Omer & Ozgener, Onder & Ozgener, Leyla, 2010. "Effects of meteorological variables on exergetic efficiency of wind turbine power plants," Renewable and Sustainable Energy Reviews, Elsevier, vol. 14(9), pages 3237-3241, December.
    11. Miladi, Rihab & Frikha, Nader & Gabsi, Slimane, 2017. "Exergy analysis of a solar-powered vacuum membrane distillation unit using two models," Energy, Elsevier, vol. 120(C), pages 872-883.
    12. EL-Seesy, Ahmed I. & Hassan, Hamdy, 2019. "Investigation of the effect of adding graphene oxide, graphene nanoplatelet, and multiwalled carbon nanotube additives with n-butanol-Jatropha methyl ester on a diesel engine performance," Renewable Energy, Elsevier, vol. 132(C), pages 558-574.
    13. Hepbasli, Arif & Alsuhaibani, Zeyad, 2011. "Exergetic and exergoeconomic aspects of wind energy systems in achieving sustainable development," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(6), pages 2810-2825, August.
    14. Ndukwu, M.C. & Bennamoun, L. & Abam, F.I. & Eke, A.B. & Ukoha, D., 2017. "Energy and exergy analysis of a solar dryer integrated with sodium sulfate decahydrate and sodium chloride as thermal storage medium," Renewable Energy, Elsevier, vol. 113(C), pages 1182-1192.
    15. Grubbström, Robert W., 2015. "On the true value of resource consumption when using energy in industrial and other processes," International Journal of Production Economics, Elsevier, vol. 170(PB), pages 377-384.
    16. Ahbabi Saray, Jabraeil & Heyhat, Mohammad Mahdi, 2022. "Modeling of a direct absorption parabolic trough collector based on using nanofluid: 4E assessment and water-energy nexus analysis," Energy, Elsevier, vol. 244(PB).
    17. Rezaie, Behnaz & Reddy, Bale V. & Rosen, Marc A., 2015. "Exergy analysis of thermal energy storage in a district energy application," Renewable Energy, Elsevier, vol. 74(C), pages 848-854.
    18. Javani, N. & Dincer, I. & Naterer, G.F., 2012. "Thermodynamic analysis of waste heat recovery for cooling systems in hybrid and electric vehicles," Energy, Elsevier, vol. 46(1), pages 109-116.
    19. Venu, Harish & Raju, V. Dhana & Subramani, Lingesan & Appavu, Prabhu, 2020. "Experimental assessment on the regulated and unregulated emissions of DI diesel engine fuelled with Chlorella emersonii methyl ester (CEME)," Renewable Energy, Elsevier, vol. 151(C), pages 88-102.
    20. BoroumandJazi, G. & Saidur, R. & Rismanchi, B. & Mekhilef, S., 2012. "A review on the relation between the energy and exergy efficiency analysis and the technical characteristic of the renewable energy systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(5), pages 3131-3135.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:251:y:2022:i:c:s0360544222006004. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.