IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v15y2023i19p14611-d1255874.html
   My bibliography  Save this article

Local Resistance Characteristics of T-Type Tee Based on Chamfering Treatment

Author

Listed:
  • Tianxiang Liu

    (School of Civil Engineering, Chang’an University, Xi’an 710064, China)

  • Shitong Li

    (School of Civil Engineering, Chang’an University, Xi’an 710064, China)

  • Chao Jiang

    (School of Civil Engineering, Chang’an University, Xi’an 710064, China)

  • Xiao Zhang

    (School of Civil Engineering, Chang’an University, Xi’an 710064, China)

  • Zijing Tan

    (School of Civil Engineering, Chang’an University, Xi’an 710064, China)

Abstract

The T-type tee is a crucial part of liquid distribution systems and is widely used in irrigation, drainage, water delivery, and agricultural fertilizer injection, among other areas. Confluence angle, pipe diameter ratio, and flow rate ratio have been the main focus of previous research. Research on the hydraulic characteristics and resistance optimization brought about by the main-side pipe intersection’s chamfering treatment is, nevertheless, incredibly rare. Optimizing the structure of the T-type tee could improve its sustainability in many aspects, such as its energy consumption, durability, and production process. In order to fill this void in the literature, the current investigation concentrated on the resistance reduction and flow properties of T-type tees by means of chamfering treatment. Using a newly proposed coefficient called the integrated local resistance coefficient, the integral flow characteristics and resistance reduction effects of T-type tees were addressed. Through the use of the verified computational fluid dynamics (CFD) method, the crossed effects of five chamfer ratios (R = 0D, 0.5D, 1D, 2D, and 3D), nine flow rate ratios (0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, and 0.9), and two pipe diameter ratios were examined. When the Reynolds number exceeded 3 × 10 5 , the flow remained in the quadratic drag region, meaning that the local resistance coefficient of T-type tees was no longer dependent on the flow velocity. In both confluence and shunt conditions for equal tees, chamfering treatment was proven to be an efficient method for reducing local resistance under these conditions. For instance, following a 1D chamfering treatment on the T-type confluence tee, at a flow ratio of 0.5, the local resistance coefficients ζ 1 and ζ 2 dropped by 68% and 82%, respectively, in comparison to the 0D condition. The effects of resistance reduction were improved by a wider chamfer radius and a higher side pipe flow rate ratio. The highest overall performance was obtained by chamfering a T-type tee with a curvature radius of 1D, taking into account flow characteristics, sustainability, processing technology, economic cost, and promotion difficulties. The chamfering procedure produced a more noticeable reduction in resistance for unequal tees with comparable velocities in the main and side pipes when the pipe diameter ratio was greater than 0.5.

Suggested Citation

  • Tianxiang Liu & Shitong Li & Chao Jiang & Xiao Zhang & Zijing Tan, 2023. "Local Resistance Characteristics of T-Type Tee Based on Chamfering Treatment," Sustainability, MDPI, vol. 15(19), pages 1-17, October.
  • Handle: RePEc:gam:jsusta:v:15:y:2023:i:19:p:14611-:d:1255874
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/15/19/14611/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2071-1050/15/19/14611/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Gan, Guohui & Riffat, Saffa B., 2000. "Numerical determination of energy losses at duct junctions," Applied Energy, Elsevier, vol. 67(3), pages 331-340, November.
    2. Sahin, Ahmet Z. & Kalyon, Muammer, 2005. "Maintaining uniform surface temperature along pipes by insulation," Energy, Elsevier, vol. 30(5), pages 637-647.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Kaynakli, Omer, 2014. "Economic thermal insulation thickness for pipes and ducts: A review study," Renewable and Sustainable Energy Reviews, Elsevier, vol. 30(C), pages 184-194.
    2. Yildiz, Abdullah & Ali Ersöz, Mustafa, 2015. "Determination of the economical optimum insulation thickness for VRF (variable refrigerant flow) systems," Energy, Elsevier, vol. 89(C), pages 835-844.
    3. Sala, J.M. & González, L.M. López & Míguez, J.L. & Eguía, J.J. & Vicuña, J.E. & Juárez, M.C. & Doménech, J., 2005. "Improvement of a chain-hardening furnace by computational fluid dynamics (CFD) simulation," Applied Energy, Elsevier, vol. 81(3), pages 260-276, July.
    4. Yildiz, Abdullah & Ersöz, Mustafa Ali, 2016. "The effect of wind speed on the economical optimum insulation thickness for HVAC duct applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 55(C), pages 1289-1300.
    5. Ertürk, Mustafa, 2016. "Optimum insulation thicknesses of pipes with respect to different insulation materials, fuels and climate zones in Turkey," Energy, Elsevier, vol. 113(C), pages 991-1003.
    6. Sala, J.M. & López-González, L.M. & Ruiz de Adana, M. & Eguía, J. & Flores, I. & Míguez, J.L., 2006. "Optimising ventilation-system design for a container-housed engine," Applied Energy, Elsevier, vol. 83(10), pages 1125-1138, October.
    7. Daşdemir, Ali & Ertürk, Mustafa & Keçebaş, Ali & Demircan, Cihan, 2017. "Effects of air gap on insulation thickness and life cycle costs for different pipe diameters in pipeline," Energy, Elsevier, vol. 122(C), pages 492-504.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:15:y:2023:i:19:p:14611-:d:1255874. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.