IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i9p3449-d811507.html
   My bibliography  Save this article

A Three-Dimensional Finite-Element Model in ABAQUS to Analyze Wellbore Instability and Determine Mud Weight Window

Author

Listed:
  • Mohammad Javad Bozorgi

    (Oil Industries Engineering and Construction (OIEC Group), Drilling Department, Tehran 1931863134, Iran)

  • Masoud Parham

    (Well Construction and Drilling Department, Pars Energy-Gostar Drilling & Exploration Company (PEDEX), Tehran 1585664811, Iran)

  • Omeid Rahmani

    (Department of Natural Resources Engineering and Management, School of Science and Engineering, University of Kurdistan Hewlêr (UKH), Erbil 44001, Kurdistan Region, Iraq
    Department of Petroleum Engineering, Mahabad Branch, Islamic Azad University, Mahabad 5913933137, Iran)

  • Ali Piroozian

    (Department of Petroleum Engineering, Faculty of Petroleum and Chemical Engineering, Science and Research Branch, Islamic Azad University, Tehran 1477893855, Iran
    Oil Exploration Operations Company (OEOC), No 234, Taleghani St., Tehran 1586737814, Iran)

  • Haylay Tsegab Gebretsadik

    (Shale Gas Research Group (SGRG), Institute of Hydrocarbon Recovery (IHR), Universiti Teknologi PETRONAS (UTP), Seri Iskandar 32610, Perak, Malaysia
    Southeast Asia Carbonate Research Laboratory, Department of Geoscience, Universiti Teknologi PETRONAS (UTP), Seri Iskandar 32610, Perak, Malaysia)

  • Syed Muhammad Ibad

    (Shale Gas Research Group (SGRG), Institute of Hydrocarbon Recovery (IHR), Universiti Teknologi PETRONAS (UTP), Seri Iskandar 32610, Perak, Malaysia
    Southeast Asia Carbonate Research Laboratory, Department of Geoscience, Universiti Teknologi PETRONAS (UTP), Seri Iskandar 32610, Perak, Malaysia)

Abstract

Wellbore instability is one of the main problems of the oil industry, causing high costs in the drilling operation. Knowing about the mechanical properties of involved formations and in-situ stresses is a privilege gained by determining an appropriate mud weight window (MWW). To this aim, a three-dimensional (3D) finite-element model was simulated in ABAQUS to analyze in-situ stresses and determine the MWW in the drilling operation of wellbore-D in the Azar oilfield. The results from the 3D finite model revealed that the Azar oilfield is structurally under the impact of a complex tectonic system dominated by two reverse faults with a configuration of σ H > σ h > σ v across the Sarvak Formation. The amount of vertical, minimum, and maximum horizontal stresses was 90.15, 90.15, and 94.66 MPa, respectively, at a depth of 4 km. Besides, the amount of pore pressure and its gradient was 46 MPa and 11.5 MPa/km, respectively. From drilling wellbore-D in the direction of the maximum horizontal stress, the lower limit of the MWW was obtained at 89 pcf. In this case, the results showed that the wellbore with a deviation angle of 10° is critical with a mud weight lower than 89 pcf. It caused the fall of the wellbore wall within the plastic zone sooner than other deviation angles. Also, in the case of drilling wellbore in the direction of minimum horizontal stress, the lower limit of the MWW was 90.3 pcf. Moreover, in the deviation angle of approximately 90°, the wellbore wall remained critical while the mud weight was below 90.3 pcf. Comparison of the results of numerical and analytical modeling showed that the modeling error falls within an acceptable value of < 4%. As a result, the wellbore with the azimuth of the maximum horizontal stress needed less mud weight and decreased the drilling costs. This particular research finding also provides insights for obtaining the lower limit of the mud weight window and determining the optimal path of the well-bore when using directional drilling technology.

Suggested Citation

  • Mohammad Javad Bozorgi & Masoud Parham & Omeid Rahmani & Ali Piroozian & Haylay Tsegab Gebretsadik & Syed Muhammad Ibad, 2022. "A Three-Dimensional Finite-Element Model in ABAQUS to Analyze Wellbore Instability and Determine Mud Weight Window," Energies, MDPI, vol. 15(9), pages 1-19, May.
  • Handle: RePEc:gam:jeners:v:15:y:2022:i:9:p:3449-:d:811507
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/9/3449/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/15/9/3449/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Baoping Chen & Bin Gong & Shanyong Wang & Chun’an Tang, 2022. "Research on Zonal Disintegration Characteristics and Failure Mechanisms of Deep Tunnel in Jointed Rock Mass with Strength Reduction Method," Mathematics, MDPI, vol. 10(6), pages 1-20, March.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Shaofeng Wang & Xin Cai & Jian Zhou & Zhengyang Song & Xiaofeng Li, 2022. "Analytical, Numerical and Big-Data-Based Methods in Deep Rock Mechanics," Mathematics, MDPI, vol. 10(18), pages 1-5, September.
    2. Yuanmin Wang & Yunqiang Wang & Song Luo & Hao Liu & Guansheng Yi & Kang Peng, 2023. "Influence of the Crack Angle on the Deformation and Failure Characteristics of Sandstone under Stepped Cyclic Uniaxial Compression with a Constant Lower Limit," Mathematics, MDPI, vol. 11(9), pages 1-19, May.
    3. Yongyi Wang & Bin Gong & Yongjun Zhang & Xiaoyu Yang & Chun’an Tang, 2022. "Progressive Fracture Behavior and Acoustic Emission Release of CJBs Affected by Joint Distance Ratio," Mathematics, MDPI, vol. 10(21), pages 1-30, November.
    4. Xin Yang & Jiangping Long, 2023. "Reliability Prediction of Tunnel Roof with a Nonlinear Failure Criterion," Mathematics, MDPI, vol. 11(4), pages 1-15, February.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:9:p:3449-:d:811507. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.