IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i9p3424-d810456.html
   My bibliography  Save this article

Murree Clay Problems and Water-Based Drilling Mud Optimization: A Case Study from the Kohat Basin in Northwestern Pakistan

Author

Listed:
  • S. M. Talha Qadri

    (School of Land Use and Environmental Change, University of the Fraser Valley, Abbotsford, BC V2S 7M7, Canada)

  • Waqas Ahmed

    (OGDCL Institute of Science and Technology, Islamabad 44000, Pakistan)

  • A. K. M. Eahsanul Haque

    (The Geosciences and Petroleum Engineering Department, University Teknologi Petronas, Seri Iskandar 32610, Malaysia)

  • Ahmed E. Radwan

    (Institute of Geological Sciences, Jagiellonian University in Krakow, 31-007 Krakow, Poland)

  • Mohammad Hail Hakimi

    (Geology Department, Faculty of Applied Science, Taiz University, Taiz 6803, Yemen)

  • Ahmed K. Abdel Aal

    (Civil Engineering Department, Faculty of Engineering, Najran University, Najran P.O. Box 1988, Saudi Arabia)

Abstract

Drilling fluids with subtle filtration and rheological characteristics are essential to optimize the functioning of oil and gas well drills. The Early Miocene Murree Formation in the Kohat Basin of Pakistan is generally referred to as the Murree Clays. When mixed with water-base drilling mud, ultra-fine particles of the Murree Formation tend to eradicate default fluid rheological properties and result in wellbore instabilities during drilling in that area. To obtain the optimized mud to deliver the drilling operation efficiently, we aimed to mitigate the impact of Murree clay on the drilling mud. We analyzed the drilling mud to observe the effects of the mud additive on clays on the basis of the samples from the Murree Clays. On the basis of the experimental tests, we observed that the rheological properties of mud significantly improved in the presence of KCl. KCl prevented the smectite group swelling inclinations and reduced rheological values to 25%, 33.3%, 48.6%, and 65.2%. The plastic viscosity increased as the concentration of clays increased; however, there was a noticeable reduction in the yield point values with the introduction of KCl. The laboratory results showed that Mud + 4% Clay + 1% KCl proved to be the best mitigation while preserving the rheological and performance characteristics of the mud. Tests enabled the scope to increase the inhibition efficiency and optimize customization. Depending on the clay present in the Murree formation, drilling fluid optimization is proposed to reduce mud-related drilling problems in this area.

Suggested Citation

  • S. M. Talha Qadri & Waqas Ahmed & A. K. M. Eahsanul Haque & Ahmed E. Radwan & Mohammad Hail Hakimi & Ahmed K. Abdel Aal, 2022. "Murree Clay Problems and Water-Based Drilling Mud Optimization: A Case Study from the Kohat Basin in Northwestern Pakistan," Energies, MDPI, vol. 15(9), pages 1-16, May.
  • Handle: RePEc:gam:jeners:v:15:y:2022:i:9:p:3424-:d:810456
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/9/3424/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/15/9/3424/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Aftab, A. & Ismail, A.R. & Ibupoto, Z.H. & Akeiber, H. & Malghani, M.G.K., 2017. "Nanoparticles based drilling muds a solution to drill elevated temperature wells: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 76(C), pages 1301-1313.
    2. Benayada, B. & Habchi, K. N. & Khodja, M., 2003. "Stabilisation of clay walls during drilling in southern Algeria," Applied Energy, Elsevier, vol. 75(1-2), pages 51-59, May.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Xinmao Zhou & Yawen Li & Xiaodong Song & Lingxuan Jin & Xixin Wang, 2023. "Thin Reservoir Identification Based on Logging Interpretation by Using the Support Vector Machine Method," Energies, MDPI, vol. 16(4), pages 1-12, February.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Razali, S.Z. & Yunus, R. & Abdul Rashid, Suraya & Lim, H.N. & Mohamed Jan, B., 2018. "Review of biodegradable synthetic-based drilling fluid: Progression, performance and future prospect," Renewable and Sustainable Energy Reviews, Elsevier, vol. 90(C), pages 171-186.
    2. Muhammad Ali & Husna Hayati Jarni & Adnan Aftab & Abdul Razak Ismail & Noori M. Cata Saady & Muhammad Faraz Sahito & Alireza Keshavarz & Stefan Iglauer & Mohammad Sarmadivaleh, 2020. "Nanomaterial-Based Drilling Fluids for Exploitation of Unconventional Reservoirs: A Review," Energies, MDPI, vol. 13(13), pages 1-30, July.
    3. Agostinho C. B. Junior & Raphael R. Silva & Giovanna L. R. Leal & Tarsila M. Tertuliano & Rafael P. Alves & Alfredo I. C. Garnica & Fabiola D. S. Curbelo, 2021. "The Influences of NP100 Surfactant and Pine-Oil Concentrations on Filtrate Volume and Filter-Cake Thickness of Microemulsion-Based Drilling Fluids (O/W)," Energies, MDPI, vol. 14(16), pages 1-15, August.
    4. Ghazi, Malika & Quaranta, Gaetana & Duplay, Joelle & Hadjamor, Raja & Khodja, Mohamed & Amar, Hamid Ait & Kessaissia, Zoubir, 2011. "Life-Cycle Impact Assessment of oil drilling mud system in Algerian arid area," Resources, Conservation & Recycling, Elsevier, vol. 55(12), pages 1222-1231.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:9:p:3424-:d:810456. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.